Vacuum Diaphragm Pumps MD 4 NT VARIO,... - Manual - Vacuubrand

advertisement
Part I
page 1 of 106
Technology for Vacuum Systems
Instructions for use
Part I of II
Part I:
Safety information - Technical data Use and operation
MD 4 NT VARIO
MV 2 NT VARIO
MV 10 VARIO-B
Speed controlled diaphragm pumps
page 2 of 106
Dear customer,
Your VACUUBRAND diaphragm pumps are designed to provide you with
many years of trouble-free service with optimal performance. Our many
years of practical experience allow us to provide a wealth of application
and safety information. Please read these instructions for use before the
initial operation of your pump.
VACUUBRAND diaphragm pumps combine our many years of experience in design, construction and practical operation, with the latest developments in material and manufacturing technology.
Our quality maxim is the ?zero defect? principle:
Every diaphragm pump, before leaving our factory, is tested intensively,
including an endurance run of 14 hours. Any faults, even those which occur rarely, are identified and can be eliminated immediately.
After completion of the endurance run, every pump is tested, and must
achieve specifications before shipment.
We are committed to providing our customers only pumps that meet this
high quality standard.
While our pumps cannot eliminate all of your work, we design, manufacture and test them to ensure that they will be an effective and trouble-free
tool to assist you in that work.
Yours,
VACUUBRAND GMBH + CO KG
After sales service:
Contact your local dealer or call +49 9342 808-5500.
Trademark index:
VACUU?LAN? (US-Reg.No 3,704,401), VACUU?BUS?, VACUU?CONTROLTM,
chemistry-HYBRIDTM, Peltronic?, TURBO?MODETM, VARIO? (US-Reg.No
3,833,788), VARIO-SPTM, ?VACUUBRAND? (US-Reg.No 3,733,388) and also
the shown company logos are trademarks of VACUUBRAND GMBH +
CO KG in Germany and/or other countries.
page 3 of 106
DE
Achtung: Die vorliegende Betriebsanleitung ist nicht in allen EU-Sprachen verf?gbar.
Der Anwender darf die beschriebenen Ger?te nur dann in Betrieb nehmen, wenn er
die vorliegende Anleitung versteht oder eine fachlich korrekte ?bersetzung der vollst?ndigen Anleitung vorliegen hat. Die Betriebsanleitung muss vor Inbetriebnahme
der Ger?te vollst?ndig gelesen und verstanden werden, und alle geforderten Ma?nahmen m?ssen eingehalten werden.
?Sicherheitshinweise f?r Vakuumger?te?
EN
Attention: This manual is not available in all languages of the EU. The user must not
operate the device if he does not understand this manual. In this case a technically
correct translation of the complete manual has to be available. The manual must
be completely read and understood before operation of the device and all required
measures must be applied.
?Safety instructions for vacuum equipment?
FR
Attention: Le mode d?emploi pr?sent n?est pas disponible dans toutes les langues
d?Union Europ?enne. L?utilisateur ne doit mettre le dispositif en marche que s?il
comprend le mode d?emploi pr?sent ou si une traduction compl?te et correcte du
mode d?emploi est sous ses yeux. Le dispositif ne doit pas ?tre mis en marche
avant que le mode d?emploi ait ?t? lu et compris compl?tement et seulement si le
mode d?emploi est observ? et tous les mesures demand?es sont prises.
?Avis de s?curit? pour des dispositifs ? vide?
BG
Внимание: Тези инструкции не са преведени на всички езици от ЕО. Потребителят не бива да работи с уреда, ако не разбира инструкциите за ползване. В
този случай е необходимо да бъде предоставен пълен технически превод на
инструкциите за ползване. Преди работа с уреда е задължително потребителят да прочете изцяло инструкциите за работа.
?Указания за безопасност за вакуумни уреди?
CN
????????????????????????????????????
????????????????????????????????????
??????????????????????????????
?????????
CZ
Upozorn?n? :Tento n?vod k pou?it? nen? k dispozici ve v?ech jazyc?ch Evropsk?
unie. U?ivatel nen? opr?vn?n po??t p??stroj pokud nerozum? tomuto n?vodu. V takov?m p??pad? je nutno zajistit technicky korektn? p?eklad manu?lu do ?e?tiny. N?vod
mus? b?t u?ivatelem prostudov?n a u?ivatel mu mus? pln? porozum?t p?ed t?m ne?
za?ne p??stroj pou??vat. U?ivatel mus? dodr?et v?echna p??slu?n? a po?adovan?
opat?en?.
?Bezpe?nostn? upozorn?n? pro vakuov? p??stroje?.
page 4 of 106
DA
Bem?rk: Denne manual foreligger ikke p? alle EU sprog. Brugeren m? ikke betjene apparatet hvis manualen ikke er forst?et. I det tilf?lde skal en teknisk korrekt
overs?ttelse af hele manual stilles til r?dighed. Manual skal v?re genneml?st og
forst?et f?r apparatet betjenes og alle n?dvendige forholdsregler skal tages.
?Sikkerhedsregler for vakuumudstyr?
EE
T?helepanu! K?esolev kasutusjuhend ei ole k?igis EL keeltes saadaval. Kasutaja
ei tohi seadet k?sitseda, kui ta ei saa kasutusjuhendist aru. Sel juhul peab saadaval
olema kogu kasutusjuhendi tehniliselt korrektne t?lge. Enne seadme kasutamist tuleb kogu juhend l?bi lugeda, see peab olema arusaadav ning k?ik n?utud meetmed
peavad olema rakendatud.
?Ohutusn?uded vaakumseadmetele?
ES
Atenci?n: Este manual no est? disponible en todos los idiomas de UE. El usuario
no debe manejar el instrumento si no entiende este manual. En este caso se debe
disponer de una traducci?n t?cnicamente correcta del manual completo. El manual
debe ser le?do y entendido completamente y deben aplicarse todas las medidas
de seguridad antes de manejar el instrumento.
?Notas sobre la seguridad para
equipos de vac?o?
FI
Huomio: T?m? k?ytt?ohje ei ole saatavilla kaikilla EU: n kielill?. K?ytt?j? ei saa k?ytt?? laitetta, jos h?n ei ymm?rr? t?t? ohjekirjaa. T?ss? tapauksessa on saatavilla oltava teknisesti oikein tehty ja t?ydellinen ohjekirjan k??nn?s. Ennen laitteen k?ytt??
on ohjekirja luettava ja ymm?rrett?v? kokonaan sek? suoritettava kaikki tarvittavat
valmistelut ja muut toimenpiteet.
?Vakuumilaitteen turvallisuustiedot?
GR
???????! : ?? ??????? ????? ??? ????? ?????????? ?? ???? ??? ??????? ??? ?????????? ??????. ? ??????? ??? ?????? ?? ????? ?? ?????????? ??? ??????? ?? ???
?????????? ?????? ??? ??????? ?????. ?? ?????? ????????? ? ??????? ?????? ??
??????????? ?????? ????????? ??? ??????? ???????. ? ??????? ?????? ?? ???????? ??? ?? ?????????? ?????? ??? ??????? ?????? ??? ?? ????? ??? ?? ??????????
????? ???? ????? ?? ?????????? ??? ???????.
??????????? ????????? ??? ???????
??????
HR
Pa?nja:ove upute ne postoje na svim jezicima Europske Unije. Korisnik nemora raditi sa aparatom ako ne razumije ove upute.U tom slucaju tehnicki ispravni prijevod
cijelih uputstava mora biti na raspolaganju. Uputstva moraju biti cijela procitana i
razumljiva prije rada sa aparatom i sve zahtijevane mjere moraju biti primjenjene.
?Sigurnosne napomene za vakuumske ure?aje?
page 5 of 106
HU
Figyelem! Ez a kezel?si utas?t?s nem ?ll rendelkez?sre az EU ?sszes nyelv?n.
Ha a felhaszn?l? nem ?rti jelen haszn?lati utas?t?s sz?veg?t, nem ?zemeltetheti a
k?sz?l?ket. Ez esetben a teljes g?pk?nyv ford?t?s?r?l gondoskodni kell. ?zembe
helyez?s el?tt a kezel?nek v?gig kell olvasnia, meg kell ?rtenie azt, tov?bb? az
?zemeltet?shez sz?ks?ges ?sszes m?r?st el kell v?geznie.
??????????????????
????????????????
?A v?kuum-k?sz?l?kekkel kapcsolatos biztons?gi tudnival?k?
IT
Attenzione: Questo manuale non ? disponibile in tutte le lingue della Comunit? Europea (CE). L?utilizzatore non deve operare con lo strumento se non comprende
questo manuale. In questo caso deve essere resa disponibile una traduzione tecnicamente corretta del manuale completo. Il manuale deve essere completamente
letto e compreso prima di operare con lo strumento e devono essere applicati tutti
gli accorgimenti richiesti.
?Istruzioni di sicurezza per apparecchi a vuoto?
JP
?????????????????????????????? ??????
????????????????????????????????? ???
????????????????????????????????????
?? ??????????????????????????????????
????????????????????????????????
???????????????
KR
?? : ? ???? ?? ??? ????? ????. ?? ? ???? ??? ??
? ???? ???? ??? ???? ????. ???? ??? ????? ??
?? ??? ??? ??????. ??? ???? ?? ? ???? ??? ??
???? ?? ???? ???? ???? ???.
?? ??? ?? ?? ??
LT
D?mesio: ?is vadovas n?ra pateikiamas visomis ES kalbomis. Naudotojui draud?iama eksploatuoti ?tais?, jeigu jis nesupranta ?io vadovo. Tokiu atveju reikia tur?ti
viso vadovo techni?kai taisykling? vertim?. Vadov? b?tina vis? perskaityti ir suprasti
pateikiamas instrukcijas prie? pradedant eksploatuoti ?tais?, bei imtis vis? reikiam?
priemoni?.
?Vakuumin?s ?rangos saugos informacija?
LV
Uzman?bu: Lietot?ja instrukcija nav pieejama vis?s ES valod?s. Lietot?js nedr?kst
lietot iek?rtu, ja vi?? nesaprot lietot?ja instrukcij? rakst?to. ??d? gad?jum?, ir nepiecie?ams nodro?in?t tehniski pareizu visas lietot?ja instrukcijas tulkojumu. Pirms
s?kt lietot iek?rtu, un, lai izpild?tu visas nepiecie?am?s pras?bas, iek?rtas lietot?ja
instrukcija ir piln?b? j?izlasa un j?saprot.
?Vakuuma iek?rtu dro??bas noteikumi?
page 6 of 106
NL
Attentie: Deze gebruiksaanwijzing is niet in alle talen van de EU verkrijgbaar. De
gebruiker moet niet met dit apparaat gaan werken als voor hem/haar de gebruiksaanwijzing niet voldoende duidelijk is. Bij gebruik van deze apparatuur is het noodzakelijk een technisch correcte vertaling van de complete gebruiksaanwijzing te
hebben. Voor het in gebruik nemen van het apparaat moet de gebruiksaanwijzing
volledig gelezen en duidelijk zijn en dienen alle benodigde maatregelen te zijn genomen.
?Veiligheidsvoorschriften voor vacu?mapparaten?
PL
Uwaga!! Ta instrukcja nie jest dost?pna we wszystkich j?zykach Unii Europejskiej.
U?ytkownik nie mo?e rozpocz?? pracy z urz?dzeniem dop?ki nie przeczyta? instrukcji i nie jest pewien wszystkich informacji w niej zawartych. Instrukcja musi byc w
ca?o?ci przeczytana i zrozumiana przed podj?ciem pracy z urz?dzeniem oraz nale?y podj?? wszystkie niezb?dne kroki zwi?zane z prawid?owym uzytkowaniem.
?Wskaz?wki bezpiecze?stwa do urz?dze? pr??niowych?
PT
Aten??o: Este manual n?o est? dispon?vel em todas as l?nguas da UE. O usu?rio
n?o deve utilizar o dispositivo, se n?o entender este manual. Neste caso, uma tradu??o tecnicamente correta do manual completo tem de estar dispon?vel. O manual deve ser lido e entendido completamente antes da utiliza??o do equipamento e
todas as medidas necess?rias devem ser aplicadas.
?Informa??o de Seguran?a
para Equipamento que funciona a V?cuo?
RO
Atentie: Acest manual nu este disponibil in toate limbile EU. Utilizatorul nu trebuie
sa lucreze cu aparatul daca daca nu intelege manualul. Astfel, va fi disponibile o
traducere corecta si completa a manualului. Manualul trebuie citit si inteles in intregime inainte de a lucra cu aparatul si a luat toate masurile care se impun.
?Instruc?iuni de siguran?? pentru aparatele de vidare?
RU
Внимание: Эта инструкция по эксплуатации не имеется на всех языках. Потребителю не дозволенно эксплуатировать данный прибор, если он не понимает
эту инструкцию. В этом случае нужен технически правильный перевод полной
инструкции. Прежде чем использовать этот прибор,
необходимо полностью прочитать и понять эту инструкцию и принять все необходимые меры.
?Указания по технике безопасности при работе с вакуумными устройствами?
page 7 of 106
SE
Varning: Denna instruktion ?r inte tillg?nglig p? alla spr?k inom EU. Anv?ndaren f?r
inte starta utrustningen om hon/han inte f?rst?r denna instruktion. Om s? ?r fallet
m?ste en tekniskt korrekt instruktion g?ras tillg?nglig. Instruktionen m?ste l?sas och
f?rst?s helt f?re utrustningen tas i drift och n?dv?ndiga ?tg?rder g?res.
?S?kerhetsinformation f?r vakuumutrustning?
SI
Pozor: Ta navodila niso na voljo v vseh jezikih EU. Uporabnik ne sme upravljati
z napravo, ?e ne razume teh navodil. V primeru nerazumljivosti mora biti na voljo
tehni?no pravilen prevod. Navodila se morajo prebrati in razumeti pred uporaba
naprave, opravljene pa moraja biti tudi vse potrebne meritve.
?Varnostni nasveti za vakuumske naprave?
SK
Upozornenie: Tento manu?l nie je k dispoz?cii vo v?etk?ch jazykoch E?. U??vate?
nesmie obsluhova? zariadenie, pokia? nerozumie tomuto manu?lu. V takomto pr?pade mus? by? k dispoz?cii technicky spr?vny preklad cel?ho manu?lu. Pred obsluhou
zariadenia je potrebn? si pre??ta? cel? manu?l a porozumie? mu, a musia by? prijat?
v?etky opatrenia.
?Bezpe?nostn? pokyny pre v?kuov? zariadenia?
TR
Dikkat : Bu kullan?m kitab?, t?m dillerde mevcut de?ildir. Kullan?c?, bu kullan?m kitab?n? anlayamad?ysa cihaz? ?al??t?rmamal?d?r. Bu durumda, komple kullan?m kitab?n?n, teknik olarak d?zg?n ?evirisinin bulunmas? gerekir. Cihaz?n ?al??t?r?lmas?ndan
?nce kullan?m kitab?n?n komple okunmas? ve anla??lmas? ve t?m gerekli ?l??mlerin
uygulanmas? gerekir.
?Vakumlu cihazlar i?in g?venlik uyar?lar??
page 8 of 106
Reset / Language selection
1
switch off
2
press both
C VC 3000
3turn
D eutsch
English
Fran?ais
Italiano
Espa?ol
T?rk?e
???
??
C V C 3000
4press
D eutsch
E nglish
Fran?ais
Italiano
E spa?ol
T?rk?e
???
??
V 2.0
Portugu?
?yccкий
Polski
N ederl.
???
Suomi
V 2.0
Portugu?
?yccкий
Polski
N ederl.
???
Suomi
page 9 of 106
Contents
Part I................................................................. 1
Reset / Language selection.............................................. 8
Safety information!............................................................ 11
Important information!.........................................................................11
General information............................................................................ 13
Intended use...................................................................................... 13
Setting up and installing the equipment............................................. 14
Ambient conditions............................................................................. 17
Operating conditions.......................................................................... 17
Safety during operation...................................................................... 19
Maintenance and repair..................................................................... 21
` Important information: Equipment marking (ATEX)...................... 23
Technical data.................................................................... 25
General technical data valid for all pumps......................................... 25
Gas inlet temperatures...................................................................... 25
Wetted parts...................................................................................... 28
Abbreviations..................................................................................... 29
Pump parts........................................................................................ 29
Use and operation............................................................. 32
Installing a pump in a vacuum system............................................... 32
During operation................................................................................. 35
Shutdown & storage........................................................................... 37
Vacuum controller CVC 3000............................................................. 38
Menu guide......................................................................... 43
Pump down function......................................................... 45
Vac Control function......................................................... 47
Auto mode.......................................................................... 50
Program function............................................................... 52
Application example.......................................................................... 54
VACUULAN function......................................................... 55
Application examples....................................................... 57
Vacuum for filtration and suction....................................................... 57
Vacuum for gel dryer,
drying chambers and vacuum ?concentrators.................................... 58
Vacuum for distillation and evaporation (e.g., rotary ?evaporator) 58
Fore-vacuum for high vacuum pumps............................................... 60
page 10 of 106
Configuration..................................................................... 61
Readjustment of VSK 3000............................................... 63
Calibration in the factory.................................................. 65
Cleaning the pressure transducer................................... 66
Part II.............................................................. 67
Interface parameters......................................................... 70
Setting of the interface...................................................................... 71
Read commands ?CVC 2000?........................................................... 72
Write commands ?CVC 2000?........................................................... 73
Read commands ?CVC 3000?........................................................... 75
Write commands ?CVC 3000?........................................................... 77
Accessories....................................................................... 80
Troubleshooting................................................................ 81
Replacing diaphragms and valves.................................. 85
Cleaning and inspecting the pump heads
(MD 4 NT VARIO / MV 2 NT VARIO)................................................. 86
Replacing the diaphragm.................................................................. 88
Assembling the pump heads............................................................. 90
Cleaning and inspecting the pump heads (MV 10 VARIO-B) ?????????? 92
Replacing the diaphragm.................................................................. 94
Assembling the pump heads............................................................. 95
Replacing the valve at the distributor (outlet side)............................ 97
Assembling the connecting hoses..................................................... 97
Replacing the device fuse................................................................. 99
Notes on return to the factory........................................ 100
Warranty........................................................................... 103
Health and safety clearance form.................................. 104
EC Declaration of Conformity of the Machinery .............. 105
page 11 of 106
Safety information!
Important information!
+Keep this manual complete and accessible to personnel at all times!
+Read this manual carefully before installing or operating the equipment. Observe the instructions
contained in this manual.
+Do not modify the equipment without authorization.
NOTICE
This manual is an integral part of the equipment described therein. It describes the safe and proper use of
the vacuum pump. The manual consists of two parts.
Make operating personnel aware of dangers arising
from the pump and the pumped substances.
VACUUBRAND disclaims any liability for inappropriate use of these pumps and for damage from failure
to follow instructions contained in this manual.
This manual is only to be used and distributed in its complete and original form. It is strictly the users? responsibility
to check carefully the validity of this manual with respect
to his product.
Manual-no.: 999163 / 02/24/2014
The following signal word panels and safety
symbols are used throughout this manual:
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury and death.
page 12 of 106
?DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
NOTICE
+WARNING indicates a hazardous situation which, if
not avoided, could result in death or serious injury.
? CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
personal injury.
Caution! Hot surface!
Disconnect equipment from AC power.
Dispose off electronic equipment according to regulations.
Formatting used in this manual:
Note: The signal word panels in all sections of this manual always refer
to all paragraphs of the same format (? / + / ? / plain text) following each
signal word panel.
page 13 of 106
General information
NOTICE
Remove all packing material from the packing box. Remove the product from its packing-box and retain all packaging until the equipment is inspected and tested. Remove the protective caps from the inlet and outlet ports
and retain for future use. Inspect the equipment promptly
and carefully.
If the equipment is damaged, notify the supplier and the
carrier in writing within three days. Retain all packing material for inspection. State the item number of the product
together with the order number and the supplier?s invoice
number. Failure to check and give notice of damage will
void any and all warranty claims for those deficiencies.
Replace the protective caps, if the equipment is not used
immediately. Store the equipment in dry and non-corrosive
conditions (see also ?Technical data?, pg. 25).
+Do not use any damaged equipment.
? Use the mounted handle or the recessed grips when
moving the pump.
Intended use
?Do not use the pump or any system parts on humans
or animals.
?Ensure that the individual components are only connected, combined and operated according to their design and as indicated in the instructions for use. Use
only original manufacturer?s spare parts and accessories. Otherwise the safety and performance of
the equipment, as well as the electromagnetic compatibility of the equipment might be reduced.
The CE mark or the cT?Vus mark may be voided if not
using original manufacturer?s spare parts.
page 14 of 106
?Comply with all notes on correct vacuum and electrical connections; see section ?Use and operation?, pg.
32.
+Do not use the pump to generate pressure.
+The pumps are designed for ambient temperatures
during operation between +50°F and +104°F (+10°C
and +40°C). Periodically check maximum temperatures if installing the pump in a cabinet or a housing.
Make sure ventilation is adequate to maintain recommended operating temperature. Install an external automatic ventilation system if necessary. If pumping hot
process gases, make sure that the maximum permitted
gas inlet temperature is not exceeded. The maximum
permitted gas inlet temperature depends on several
parameters like inlet pressure and ambient temperature (see ?Technical data?, pg. 25).
+Particles and dust must not enter the pump.
+Do not pump liquids.
? Ensure that the pump is chemically resistant to the
pumped substances prior to operation.
NOTICE
Use the equipment only as intended, that is, for generation, measurement, and control of vacuum in vessels designed for that purpose. Any other use will automatically
invalidate all warranty and liability claims.
Remain aware of safety and risks.
Setting up and installing the equipment
? Equipment must be connected only to a suitable electrical supply and a suitable ground point. As such,
the plug must be plugged into an outlet that is properly
grounded. Failure to connect the motor to ground may
result in deadly electrical shock.
page 15 of 106
The supply cable may be fitted with a molded European IEC plug or a plug suitable for your local electrical
supply. The cable contains wires color coded as follows: green or green and yellow: ground; blue or white:
neutral; brown or black: hot.
?Due to the high compression ratio, the pump may generate overpressure at the outlet. Check pressure compatibility with system components (e.g., exhaust pipeline or exhaust valve) at the outlet.
?Do not permit any uncontrolled pressurizing. Make
sure that the exhaust pipeline cannot become blocked.
If there is an exhaust isolation valve, make sure that you
cannot operate the equipment with the valve closed to
avoid a risk of bursting!
?Maximum permissible pressure at the pressure transducer: 21.8 psi (1.5 bar) absolute.
?Keep the electrical power cord away from heated surfaces.
? Provide a firm, level platform for the equipment. Check
that the system which you are going to evacuate is
mechanically stable. Check that all fittings are secure.
Ensure a stable position of the pump without any mechanical contact other than the pump feet.
? Comply with maximum permissible pressures at inlet and outlet and with maximum permissible pressure differences between inlet and outlet. See section
?Technical data?, pg. 25. Do not operate the pump
with overpressure at the inlet.
? Comply with maximum permissible pressures at the
pressure transducer. See section ?Technical data?, pg.
25.
? Avoid overpressure of more than 17.5 psi absolute (1.2
bar absolute) in the event that inert gas is connected to
the pump, or to a venting valve.
page 16 of 106
? Note: Flexible elements will shrink when evacuated.
? Connect hoses gas tight at inlet and outlet of the pump.
? Connect hoses gas tight at the pressure transducer.
? Ensure that no foreign objects can be drawn into the
pump.
? Check the power source and the pump?s rating plate
to be sure that the power source and the equipment
match in voltage, phase, and frequency.
NOTICE
Make sure ventilation is adequate to maintain recommended operating temperature. Keep a minimum distance of
2 in (5 cm) between the cooling fan and surrounding items
(e.g., housing, walls, etc.), or else install an external automatic ventilation system. Check fan regularly for dust/dirt.
Clean fan guard grill if necessary to avoid a reduction of
ventilation.
MV 10 VARIO-B: Do not place the pump on soft surfaces
(e.g., rubber foam) during operation. This may reduce or
block the fans? air supply.
Position the pressure transducer and its vacuum line in
such a way that condensate cannot flow towards the pressure transducer.
Use only hoses at the inlet and outlet of the pump with
an inner diameter at least as large as the diameter of the
pump?s tubing (to avoid overpressure at the outlet, and
reduction of pumping speed at the inlet).
Allow the equipment to equilibrate to ambient temperature
if you bring it from cold environment into a room prior to
operation. Notice if there is water condensation on cold
surfaces.
Comply with all applicable and relevant safety requirements (regulations and guidelines). Implement the required actions and adopt suitable safety measures.
page 17 of 106
Ambient conditions
?Do not reach for this product if it has fallen into liquid.
There is a risk of deadly electrical shock. Unplug the
system immediately.
+Do not use this product in an area where it can fall or
be pulled into water or other liquids.
? Adopt suitable measures in case of differences from
recommended conditions, e.g., using the equipment
outdoors, installation in higher altitudes, conductive
pollution or external condensation on the pump.
? Do not operate this product near flames.
NOTICE
To the best of our knowledge the equipment is in compliance with the requirements of the applicable EC-directives and harmonized standards (see ?Declaration of Conformity?) with regard to design, type and model. Directive
EN 61010-1 gives in detail the conditions under which the
equipment can be operated safely (see also IP degree of
protection, ?Technical data?, pg. 25).
Operating conditions
?These pumps are not approved for operation in potentially explosive atmospheres. Do not operate the
pumps in potentially explosive atmospheres.
?Pumps without the ? ? mark on the rating plate are
not approved for the pumping of potentially explosive atmospheres. Do not pump potentially explosive atmospheres with those pumps
?Pumps bearing the ? ? mark on their rating plates
are approved for the pumping of potentially explosive atmospheres according to their classification II 3G IIC T3 X according to ATEX, but they are
not approved for operation in potentially explosive
atmospheres(see section ?` Important information:
Equipment marking (ATEX)?, pg. 23).
page 18 of 106
?The pumps are not suitable to pump any of the substances listed below.
Do not pump:
- unstable substances
-substances which react explosively under impact
(mechanical stress) without air
- substances which react explosively when being exposed to elevated temperatures without air,
- substances subject to auto-ignition,
- substances which are inflammable without air
- explosive substances.
?The pumps are not approved for operation below
ground. Do not operate the pump below ground.
? Do not pump substances which may form deposits inside the pump. The pumps are not suitable for
pumping substances which may form deposits inside
the pump. Deposits and condensate in the pump may
lead to increased temperatures even to the point of
exceeding the maximum permitted temperatures.
? Check the inlet and outlet of the pump, if there is a
danger of forming deposits inside the pump, e.g., in
the pump chambers (the pump chamber is the part
between diaphragm and head cover. See section ?Replacing diaphragms and valves?, pg. 85). Inspect the
pump chambers regularly and clean if necessary.
? Consider interactions and chemical reactions of
the pumped media. Ensure that the materials of the
pump?s wetted parts are compatible with the pumped
substances, see section ?Technical data?, pg. 25.
When changing the substances pumped, we recommend purging the pump with air or inert gas prior to
changing the pumped media. Purging the pump will
pump out residues and it will reduce the possibility of
reactions of the pumped substances with each other
and with the pump?s materials.
page 19 of 106
Safety during operation
? Adopt suitable measures to prevent the release of dangerous, toxic, explosive, corrosive, noxious or polluting fluids, vapors and gases. To prevent any emission
of such substances from the pump outlet, install an
appropriate collecting and disposal system and take
protective action for pump and environment.
?You must take suitable precautions to prevent any formation of explosive mixtures in the pump chamber or
at the outlet of the pump. In case, e.g., of a diaphragm
failure, mechanically generated sparks, hot surfaces
or static electricity may ignite these mixtures. Use inert
gas for venting, if necessary.
?Drain appropriately or otherwise remove any potentially explosive mixtures at the outlet of the pump, or
dilute them to non-explosive concentrations.
?Never operate this pump if it has a damaged cord or
plug.
+If the pump is not working properly, has been dropped
or has fallen into water, contact your pump service provider.
+Prevent any part of the human body from coming into
contact with vacuum.
+Make sure that the exhaust pipeline cannot become
blocked.
?Attention: At pressures above approximately 795 Torr
(1060 mbar) the pressure reading becomes incorrect
due to saturation of the pressure transducer. The display flashes. Release pressure immediately! Risk of
bursting!
+Comply with applicable regulations when disposing of
chemicals. Take into consideration that chemicals may
page 20 of 106
be contaminated. Take adequate precautions to protect people from the effects of dangerous substances
(chemicals, thermal decomposition products of fluoroelastomers). Use appropriate protective clothing and
safety goggles.
+Interruption of the pump (e.g., due to power failure),
failure of connected components or of parts of the supply, or change in parameters must not be allowed to
lead to dangerous conditions. In case of a diaphragm
failure or in case of a leak in the manifold, pumped
substances might be released into the environment or
into the pump housing or motor.
Comply with all notes regarding proper use of the
pumps, as well as operation and maintenance guidance.
+The residual leak rate of the equipment might render
possible an exchange of gas, albeit extremely slight,
between the environment and the vacuum system.
Adopt suitable measures to prevent contamination of
the pumped substances or the environment.
? Ensure that no parts of your clothing, hair or fingers
can be caught or drawn in at the inlet of the pump.
Never insert fingers or drop any other object into the
inlet or outlet.
? You must take suitable precautions to prevent any
dangerous situation from arising if the controller starts
a NT VARIO or VARIO-B pump, switches a coolant
valve or opens a venting valve.
? Attention: If the controller is set to Autostart, the process will start immediately after a power failure without pressing any further key. It is your responsibility to
ensure that automatic start-up of the system will not
lead to any dangerous condition. Provide appropriate
safety measures. Check prior to starting the process
whether the option ?Autostart? (menu: configuration) is
enabled.
page 21 of 106
? Pay attention to the safety symbol ?hot surfaces? on
the equipment. Hot parts may cause burns if touched.
Adopt suitable measures to prevent any danger arising from hot surfaces or electric sparks. Ensure that
hot surfaces of the pump do not cause burns. Provide
a suitable contact guard if necessary.
NOTICE
Prevent the backpressure of gases and the backflow of
condensates at the outlet.
Provide appropriate protective measures to allow for the
possibility of failure and malfunction. The protective measures must also allow for the requirements of the respective application.
In case of overload, the motor is shut down by a self-hold
thermal cutout in the winding.
Note: Only manual reset is possible. Press the START/
STOP key at the controller to confirm the error message.
Switch off the pump and disconnect from the power source.
Identify and eliminate the cause of failure. Wait approx.
five minutes before restarting the pump.
Maintenance and repair
NOTICE
In order to comply with laws (occupational, health and
safety regulations, safety at work law and regulations for
environmental protection) vacuum pumps, components
and measuring instruments can only be returned when
certain procedures (see section ?Notes on return to the
factory?, pg. 100) are followed.
Take advantage of our service seminars, which put special
focus on the maintenance and repair of vacuum pumps.
For details and for the online ?Instructions for repair? manual see www.vacuubrand.com.
page 22 of 106
In normal use, the lifetime of the diaphragms and valves is
typically 15,000 operating hours. Bearings have a typical
durability of 40000 h.
?Ensure that the pump cannot be operated accidentally. Never operate the pump if covers or other
parts of the pump are disassembled.
?Switch off the pump. Disconnect the electrical
power cord and wait two minutes before starting
maintenance to allow the capacitors to discharge.
?Note: The pump may be contaminated with process
chemicals, which have been pumped during operation.
Ensure that the pump is completely decontaminated
before maintenance commences.
?Take adequate precautions to protect people from the
effects of dangerous substances if contamination has
occurred. Use appropriate protective clothing, safety
goggles and protective gloves.
+Wear parts have to be replaced regularly.
+Never operate a defective or damaged pump.
+Vent the pump before starting maintenance. Isolate the
pump and other components from the vacuum system.
Allow sufficient cooling of the pump. Drain condensate,
if applicable.
NOTICE
Ensure that maintenance is done only by suitably trained
and supervised technicians. Ensure that the maintenance
technician is familiar with the safety procedures which relate to the products processed by the pumping system.
Only dismantle the pump as far as necessary.
page 23 of 106
` Important information: Equipment marking (ATEX)
VACUUBRAND equipment bearing mark (see rating plate)
` II 3G IIC T3 X
Internal Atm. only
Tech. File Ref.: VAC-EX01
and
VACUUBRAND equipment bearing mark (see rating plate)
` X see manual
For equipment labelled with ?` X see manual? the following classification according to Directive 94/9/EC (ATEX) is valid: ` II 3G IIC T3 X,
Internal Atm. only, Tech. File Ref.: VAC-EX01.
The classification II 3G IIC T3 X according to ATEX is only valid for the inner part (wetted part, pumped gas or vapor) of the equipment. The equipment is not suitable for use in external, potentially explosive atmospheres
(environment).
The overall category of the equipment depends on the connected components. If the connected components do not comply with the classification of the VACUUBRAND equipment, the specified category of the
VACUUBRAND equipment is no longer valid.
Vacuum pumps and vacuum gauges in category 3 are intended for connection to equipment in which during normal operation explosive atmospheres caused by gases, vapors or mists normally don?t occur; or, if they
do occur, are likely to do so only infrequently and for a short period only.
Equipment in this category ensures the requisite level of protection during normal operation.
The use of gas ballast or the operation of venting valves is only permitted if thereby explosive atmospheres normally don?t occur in the interior
of the equipment or, if they do occur, are likely to do so only infrequently
and for a short period.
page 24 of 106
The pumps are marked with ?X? (according to EN 13463-1), i.e., restrictions of the operation conditions:
? The equipment is designated for a low degree of mechanical stress
and has to be installed in a way so that it cannot be damaged from
outside.
Pumping units have to be installed so that they are protected against
shocks from the outside and against glass splinters in the event of
breakage (implosion).
? The equipment is designated for an ambient and gas inlet temperature
during operation of +10 to +40°C. Never exceed these ambient and
gas inlet temperatures. If pumping / measuring gases which are not
potentially explosive, extended gas inlet temperatures are permissible.
See instructions for use, section ?Gas inlet temperatures? or ?Technical data?.
After any intervention at the equipment (e.g., repair / maintenance) the ultimate vacuum of the pump has to be checked. Only if the pump achieves
its specified ultimate vacuum is the pump?s leak rate low enough to ensure that no explosive atmospheres will occur in the interior of the equipment.
After any intervention at the vacuum sensor, the leak rate of the equipment has to be checked.
Attention: This manual is not available in all
languages of the EU. The user must not operate the device if he does not understand
this manual. In this case a technically correct translation of the complete manual has
to be available. The manual must be completely read and understood before operation of the device. All specified measures
must be applied, or else must be replaced
by equivalent measures at the user?s own
risk.
page 25 of 106
Technical data
General technical data valid for all pumps
Maximum permissible inlet pressure
(absolute)
psi
(bar)
16
(1.1)
Maximum permissible outlet pressure
(absolute)
psi
(bar)
16
(1.1)
Maximum pressure difference between
inlet and outlet
psi
(bar)
16
(1.1)
Permissible ambient temperature
storage / operation
°F
(°C)
14 to 140 / 50 to 104
(-10 to +60 / +10 to +40)
Permissible relative atmospheric moisture during operation (no condensation)
Maximum permissible installation altitude
above mean sea level
Rated motor power
No-load speed 50/60 Hz
%
30 to 85
ft
(m)
6500
(2000)
hp
(kW)
0.77
(0.575)
rpm
30 - 2400
Device fuse
100-120V: slow blow fuse 8A
200-230V: slow blow fuse 4A
Motor protection
thermal cutout, manual reset
Degree of protection IEC 529
IP 20
Gas inlet temperatures
Operating condition
Inlet pressure
Continuous operation
> 75 Torr (100 mbar)
(high gas load)
< 75 Torr (100 mbar)
(low gas load)
< 75 Torr (100 mbar)
(low gas load)
Continuous operation
Short-time
(< 5 minutes)
Permitted range of gas
temperatures at inlet
? 50 °F to 104 °F
(+10°C to +40°C)
? 32 °F to 140 °F*
(0°C to +60°C*)
? 14 °F to 176 °F*
(-10°C to +80°C*)
* if pumping potentially explosive atmospheres: 50 °F to 104 °F (+10°C to +40°C)
page 26 of 106
Type
Maximum pumping speed
cfm
50/60 Hz (ISO 21360)
(m3/h)
Ultimate vacuum
Torr
(absolute) *
(mbar)
Maximum permissible range of supply voltage ( ?10% )
Attention: Observe specifications of
rating plate!
Maximum rated current at:
100-120 V~ 50/60 Hz
A
200-230 V~ 50/60 Hz
A
Inlet
MD 4 NT
VARIO
MV 2 NT
VARIO
MV 10
VARIO-B
3.4
(5.7)
0.75
(1.0)
1.9
(3.3)
0.2
(0.3)
6.1
(10.4)
0.2
(0.3)
100-120 V~ 50/60 Hz
200-230 V~ 50/60 Hz
6.3
2.5
small flange DN 16
Outlet
A-weighted
emission
sound pressure level**
(uncertainty KpA : 3 dB(A))
Dimensions L x W x H
approx.
Weight approx.
-
3.5
small flange
DN 25
silencer
dB(A)
in
(mm)
45
45
12.8 x 9.3 x 9.6
(325 x 235 x 245)
lbs. (kg) 41.0 (18.6)
41.7 (18.9)
52
19.1 x 8.7 x
11.9
(486 x 222 x
303)
55.1 (25.0)
* Ultimate vacuum at setting ?Pump down? at speed ?HI?
**Measurement according to EN ISO 2151:2004 and EN ISO 3744:1995 at 1500rpm and ultimate vacuum with standard silencer at outlet.
Controller
CVC 3000
Pressure transducer
external gauge head VSK 3000,
ceramic diaphragm (alumina),
capacitive, absolute pressure,
gas type independent
Display
LCD graphic display, illuminated
Pressure units / scale (selectable)
Torr, mbar or hPa
Measuring range (absolute)
795 - 0.1 Torr (1060 - 0.1 mbar)
Maximum control range (absolute)*
795 - 0.1 Torr (1060 - 0.1 mbar)
Resolution (display)
0.1 Torr (mbar)
* The actual vacuum control range in your application might be reduced due to ultimate vacuum
of the pump, volume of gas present, etc.
page 27 of 106
Controller
Maximum permissible pressure at
pressure transducer (absolute)
Measurement uncertainty (absolute)
after careful adjustment and at constant
temperature
Temperature coefficient
Maximum permissible temperature of
gaseous media**
CVC 3000
1125 Torr (1.5 bar)
<? 0.75 Torr (1 mbar)
<? 0.05 Torr/K (0.07 mbar/K)
continuous operation: 104°F (40°C),
for short periods (less than 5 minutes)
up to 176°F (80°C)
Ambient temperature range (operation)
50°F to 104°F (10°C to +40°C)
Ambient temperature range (storage)
14°F to 158°F (-10°C to +70°C)
Permissible relative atmospheric moisture during operation (no condensation)
30% to 85%
Maximum permitted current of connected valves (connected components)
4A
Degree of protection IEC 529
(front side)
IP 42
Degree of protection IEC 529
(gauge head VSK 3000)
IP 54
Measurement connection of pressure
transducer
Cable length of pressure transducer
small flange DN 16 or
hose nozzle for tubing
I.D. 1/4? / 3/8? (6 / 10 mm)
approx. 5?6? (2m)
Supply voltage VSK 3000
(via VACUU ? BUS)
6-30 V= / 5 mA
Communication VSK 3000
VACUU ? BUS
Interface
Dimensions CVC 3000 L x W x H
(with foot)
Dimensions VSK 3000
housing diameter
length with measurement connection
Weight CVC 3000
VSK 3000 (with small flange)
RS-232 C
5.4? x 4.9? x 4.5?
(138 mm x 124 mm x 115 mm)
2.4? (60 mm)
2.4? (60 mm) with small flange
0.97 lb (440 g)
0.41 lb (185 g)
** if pumping potentially explosive atmospheres: 50 °F to 104 °F (+10°C to +40°C)
We reserve the right for technical modification without prior notice!
page 28 of 106
Wetted parts
Components
Wetted materials
Pump
Housing cover
Aluminum alloy
(AlMgSi0.5 or AlSi12)
Head cover
Aluminum alloy (AlSi12)
Diaphragm clamping disc
Aluminum alloy (AlSi12)
Diaphragm
FPM
Valves
FPM
O-rings
FPM
Connection tube
Aluminum alloy (AlMgSi0.5)
Fittings (MV 10 VARIO-B)
Aluminum anodized
Tubing (MV 10 VARIO-B)
PE
Seal ring (MV 10 VARIO-B)
FPM
Small flange
Stainless steel
Silencer
PA / PE / aluminum or
aluminum alloy / silicone
Overpressure safety relief device
(outlet MV 10 VARIO-B)
Stainless steel / silicone rubber
VSK 3000
Sensor
Aluminum oxide ceramic
Seal at sensor
Chemically resistant fluoroelastomer
Sensor housing
PPS glass fiber reinforced
Small flange
Stainless steel
Hose nozzle
PP
We reserve the right for technical modification without prior notice!
page 29 of 106
Abbreviations
FPM:Fluoroelastomer
PA:Polyamide
PE:
Polyethylene
PP:Polypropylene
PPS: Polyphenylene sulfide
Pump parts
Position
Component
1
Diaphragm pump NT VARIO
2
Controller CVC 3000
3
Pressure transducer VSK 3000
4
Mains connection
5
ON/OFF switch
6
Pump rating plate
7
Fan
8
Inlet
9
Outlet (silencer)
10
Recessed grip / handle
11
VACUU?BUS cable to controller
12
Fuse holder
13
Overpressure safety relief device
page 30 of 106
MD 4 NT VARIO / MV 2 NT VARIO
(shown: MV 2 NT VARIO)
5
4
10
7
10
1
7
11
12
9
6
8
2
3
MV 10 VARIO-B
10
10
11
12
5
13
4
3
8
2
9
page 31 of 106
Rear side CVC 3000
jacks for connection of
VACUU?BUS components
(e.g., VSK 3000, coolant
valve)
rating plate
Connection plug of the VACUU ? BUS
line to NT VARIO / VARIO-B pump
serial interface
RS-232 C
page 32 of 106
Use and operation
When switching on the controller CVC 3000 for the very first time, a menu
to select the language of the controller menu is displayed. Select the desired language (e.g., ?English?) by turning the selection knob and press
to confirm. Then select the pressure unit (?mbar?, ?Torr? or ?hPa?) in the
same way.
It is possible to access the language selection menu at any time
by switching on the controller while keeping the selection knob
pressed.
Installing a pump in a vacuum system
?If dangerous or polluting fluids could be released at
the outlet, install an appropriate system to catch and
dispose of those fluids.
+Connect a gas-tight exhaust line at the pump outlet if
necessary. Always vent exhaust gases appropriately
(e.g., into a fume hood).
+Never block the gas outlet. The exhaust line must always be free of obstructions (no back pressure) to ensure an unimpeded discharge of gas. The cross-section of the outlet tubing must be at least the size of the
pump?s exhaust connection.
?Maximum permissible pressure: 21.8 psi (1.5 bar) absolute.
?Attention: At pressures above approximately 795 Torr
(1060 mbar) the pressure reading becomes incorrect
due to saturation of the pressure transducer. The display will flash. Release pressure immediately! Risk of
bursting!
+Particles and dust must not be aspirated. If necessary,
you must install appropriate filters. You must ensure
their suitability concerning gas flow, chemical resistance and resistance to clogging prior to use.
page 33 of 106
+Make sure ventilation is adequate, especially if the pump
is installed in an enclosure, or if the ambient temperature is elevated. Provide external ventilation, if necessary.
? Reduce the transmission of vibration. Prevent mechanical load due to rigid pipelines. Insert elastic hoses or
flexible elements as couplings between the pump and
rigid pipes.
Note: Flexible elements will compress or flatten when
evacuated if not designed for use under vacuum.
? Hose connections at the pump inlet must always be
gas tight.
? A power failure may cause accidental ventilation of the
pump. If this constitutes a potential source of danger,
take appropriate safety measures.
? Check the power source and the pump?s rating plate
to be sure that the power source and the equipment
match in voltage, phase, and frequency.
NOTICE
Make sure ventilation is adequate to maintain recommended operating temperature. Keep a minimum distance of
2 in (5 cm) between the cooling fan and surrounding items
(e.g., housing, walls, etc.), or else install an external automatic ventilation system.
Use connecting hoses with large diameter and keep them
as short as possible to avoid flow losses. Locate the pump
as closely as possible to the application.
Always install outlet tubing descending from the pump or
provide other measures to avoid backflow of condensate
towards the pump.
Use a suitable valve to isolate the pump from the vacuum
application. This is to allow the pump to warm up before
pumping condensable vapors and to clean the pump after
use before it is switched off.
page 34 of 106
When assembling, ensure vacuum-tightness. After assembly, check the whole system for leaks.
Secure hose connections at the pump appropriately, e.g.,
with hose clamps, to protect against accidental detachment.
The VACUUBRAND controller CVC 3000 can only be
operated with components compatible with the VACUUBRAND VACUU?BUS system, (see ?Accessories?, pg.
80).
The vacuum controller CVC 3000 controls VACUUBRAND
diaphragm pumps NT VARIO and VARIO-B, and optional
coolant and venting valves. Connected components (e.g.,
venting valve, external pressure transducer 3000 series)
are automatically identified and configurated. Identical
components must be configurated beforehand; information upon request.
Connect the controller CVC 3000 via the VACUU?BUS cable of the NT VARIO or VARIO-B pump to the diaphragm
pump.
Do not use more than one controller within the same
VACUU?BUS system.
Several controllers in the same VACUU?BUS system
will interfere with each other and result in error messages of the connected components (pumps, valves).
VSK 3000
The VSK 3000 is equipped with a capacitive pressure
transducer with ceramic diaphragm. It measures the actual pressure independently of the gas type, and with reference to the vacuum, i.e., absolute.
Connect the VSK 3000 pressure transducer via the
VACUU?BUS cable to the CVC 3000 controller.
Attention: Do not apply off-axis forces when assembling or removing plug connections! Observe correct orientation of the plug. To connect further components use
VACUU?BUS Y-adapters and extension cables.
page 35 of 106
Connect the pressure transducer via hose or small flange
connection to the vacuum application. Do not mount the
pressure transducer directly at the pump but close to the
application. The cross-section of the tubing should be as
large as possible.
Inside a vacuum system where evaporation occurs, e.g.,
a rotary evaporator, the vacuum is not uniform. For example, a condenser can act as a pump, or the vacuum in
the connecting tubing can be higher or lower than in the
application itself. This affects the measurement results as
well as the control levels. Therefore, carefully choose the
position where to connect the pressure transducer.
Position the pressure transducer and its vacuum line in
such a way that condensate cannot flow towards the pressure transducer. Condensate and deposits will affect the
measurement results. Clean the pressure transducer, if
necessary. See section ?Cleaning the pressure transducer?, pg. 66.
Installing the hose nozzle at the VSK 3000:
Unscrew the small flange. Slip hose nozzle with clamping
ring onto the vacuum connection and fasten with union
nut.
VACUU?BUS
The CVC 3000 controller uses VACUU?BUS protocol to
read out the pressure transducer via VACUU?BUS line.
Maximum cable length inside buildings: 32yd (30m).
VACUU?BUS extension cable 2.2 yd (2 meters): order-no.
612552.
During operation
?Vent and dispose of potentially dangerous gases or
vapors at the outlet of the pump appropriately.
page 36 of 106
+Due to the high compression ratio, the pump might
generate overpressure at the outlet. Check pressure
compatibility with system components (e.g., exhaust
tubing or exhaust valve) at the outlet. Ensure that the
pump outlet is neither blocked nor restricted.
+Maximum ambient temperature: 104 °F (40 °C)
Check the maximum temperatures, if installing the
pump in a cabinet or a housing. Make sure ventilation
is adequate, especially if the ambient temperature is
elevated.
+Operation with silencer at the outlet: Operating the
pump at a high inlet pressure or pumping dusty gases for a long time may cause clogging of the silencer.
Check the silencer regularly and replace if necessary,
or install a hose nozzle (order no. 639758) with sealing
ring (order no. 639729) instead.
? If the pump is installed at an altitude of more than 6500
ft (2000 m) above mean sea level, check compatibility
with applicable safety requirements, and adopt suitable measures. There is a risk of the motor overheating due to insufficient cooling.
? Check compatibility with the maximally permitted
pressure at outlet and the maximum pressure difference between inlet and outlet ports.
NOTICE
Do not start the pump if the pressure difference between
inlet and outlet ports exceeds max. 16.0 psi (1.1 bar).
Attempts to start the pump at higher pressure difference
may cause stalling and damage of the motor.
Prevent internal condensation, transfer of liquids or dust.
The diaphragms and valves will be damaged, if liquids are
pumped in significant amounts.
Check the pump regularly for external soiling and deposits. Clean the pump if necessary to avoid an increase of
the pump?s operating temperature.
page 37 of 106
In case of overload, the motor is shut down by a self-hold
thermal circuit breaker in the winding.
Note: Only a manual reset is possible. Press the START/
STOP key at the controller to confirm the error message.
Switch off the pump and disconnect the electrical power
cord. Identify and eliminate the cause of failure. Wait approx. five minutes before restarting the pump.
Check fan regularly for dust/dirt. Clean if necessary. Avoid
overheating (e.g., due to hot process gases).
A warm up period (approximately 15 min.) is required to
ensure that the rated ultimate vacuum and pumping speed
are attained.
Shutdown & storage
The pump can be switched off under vacuum.
NOTICE
Short-term:
Has the pump been exposed to condensate?
- Allow the pump to continue to run at atmospheric pressure for a few minutes.
Has the pump been exposed to media which may damage
the pump materials or form deposits?
- Check and clean pump heads if necessary.
Has the pressure transducer been exposed to media which
may form deposits?
- Clean pressure transducer if necessary.
Long-term:
- Take measures as described above regarding shortterm shutdown.
- Separate the pump from the application.
- Close inlet and outlet ports (e.g., with transport caps).
- Store the pump under dry conditions.
page 38 of 106
Vacuum controller CVC 3000
When switching on the controller CVC 3000 for the very first time, a menu
to select the language of the controller menu is displayed. Select the desired language, e.g., ?English? by turning the selection knob and pressing
to confirm. Then select the pressure unit (?mbar?, ?Torr? or? hPa?) in the
same way.
It is possible to access the language selection menu at any time
by switching on the controller while keeping the selection knob
pressed.
After switching on the device, the version number of the software is
displayed, followed by the preselected function and the pressure ?reading.
Attention: Do not assemble or remove plug connections off-axis!
Orient the plug correctly before inserting. To connect additional
components use VACUU?BUS Y-adapters and extension cables. If
an external pressure transducer is connected, it is recognized automatically. Further information on how to use several sensors simultaneously is available upon request.
Keys
VENT:
? A short tap vents momentarily;
process continues.
? Pressing longer than 2 seconds vents the
system to atmospheric pressure (to 788 Torr
(1050 mbar) at maximum); process stops.
MODE:
? Selects menu ?function?
? Use for temporary switching during
operation to other functions
Start or Stop the process
ON/OFF switch
page 39 of 106
Selection knob
?
?
?
?
?
Press to reach the set-up menu of the function
Turn to choose the parameter you want to modify
Press to select the parameter you want to modify
Turn to change the set value of the parameter
Press to confirm change of value and to reach further
parameters, or to leave the set-up menu
Display and symbols
Vac control
100
1013.2
mbar
Selected function (displayed in the upper left corner):
(A ?function? is an operation mode of the CVC 3000 controller.)
Pump down / Vac control / Auto mode (only with NT VARIO pump) /
Program / VACUULAN / Configuration
Other display symbols:
1013.2 Actual absolute pressure at the pressure transducer
mbar / Torr / hPa Preselected pressure unit
page 40 of 106
100
100
Vacuum control to a preset vacuum value (here:
100 mbar/Torr/hPa)
(with NT pump / with NT VARIO pump)
Actual pressure is in the range ??????????????????
??????????????????
Set vacuum + hysteresis? (with NT pump) / Actual pressure = ?Set
vacuum? (with NT VARIO pump)
Flashing: The actual pressure is greater than the preset maximum value (?Maximum?)
Minimum value (?Minimum?) reached
00:00:00
Process runtime (only if process control is running)
Pump down (continuous pumping)
50%
5
Pump symbol is displayed when pump is running. With an
NT VARIO pump, the pump?s motor speed is also displayed
in % of full speed.
Time meter is running (in function ?VACUULAN?); remaining
time in minutes is displayed
In-line valve switched on
Venting valve switched on
Coolant valve switched on
PC symbol: controller is in remote operation
Control is running
Warning notice (if necessary in combination with other symbols), flashing
Level sensor activated; catchpots need to be emptied.
Peltronic emission condenser connected
page 41 of 106
Notes on selecting the function
The CVC 3000 controller can be adapted to the specific application by
choosing the appropriate function depending on the connected components and the requirements of the application.
Automatic detection of the components
When switching on the controller, the configuration of the connected components is checked automatically.
Connected components (pump NT VARIO / VARIO-B, gauge head VSK
3000, valves) are detected automatically and controlled by the CVC
3000 until the controller is switched off. Switch off/on the controller to renew the configuration.
The last mode of operation and the preselected values (e.g., for pressure, speed or time for switching off) are stored.
If the preselections are chosen appropriately, it is possible to start immediately if similar operating conditions are desired.
The controller features five functions and one configuration menu,
see section ?Menu guide?. Each of these functions involves different menu
options, which are presented automatically and reflect the connected
components. The types of components connected (e.g., valves) determine the active menu items.
Changing the function:
?Switch controller on.
?Press ?START/STOP? key to terminate control in case control is running (e.g., if ?Autostart? is activated).
?Press ?MODE? key.
?Select function with knob and press to confirm.
?Depending on the selected function and system components, the controller provides different operating control, as follows:
??Pump down??
? Manages the continuous speed control of the NT VARIO/VARIO-B
pumps depending on preselected pressure and time settings.
? Coolant valve
page 42 of 106
?Vac control?
? With pressure preselection, controls a NT VARIO / VARIO-B pump to
maintain pinpoint control of that pressure.
? Coolant valve
?Auto mode?
? Provides fully automatic boiling point determination and adaptation
with pinpoint precision, and optimization of pumping speed with NT
VARIO / VARIO-B pumps.
? Coolant valve
??Program??
? Control pump based on time and pressure preselections, or ?Auto
mode?
? Coolant valve
? Venting valve
?VACUULAN?
? Use continuous speed control to manage NT VARIO/VARIO-B pumps,
based on pressure and time preselections.
? Coolant valve
??Configuration??
Preselections for
? Adjustment of the pressure transducer
? Interface RS-232
? Sensors (configuration and switching between several sensors)
? Display (brightness and contrast of the display, language, sound)
? Autostart (automatic restart after power failure)
? Defaults (reset the controller to factory set values)
?You may also access the ?Configuration? menu by pressing the selection knob while the start display is shown.
page 43 of 106
Menu guide
Pump down
Pump down
*
Function
MODE
Speed HI
Minimum
Off
Delay
Off
Duration
Off
- - - - - - Graphic - - - - - - - - - - - - Back - - - - - - -
1013.2
mbar
*
Pump down
Vac control
Auto mode
Program
VACUULAN
Configuration
Configuration
Adjustment
760 Torr
RS-232...
Sensors...
Display...
Autostart Off
Defaults Cancel
- - - - - - - Back - - - - - - -
- - - - - - - - Back - - - - - - -
*
VACUULAN
MODE
1013.2
mbar
* :
or automatically after 20 seconds
without action
VACUULAN
Set vacuum
19 Torr
Switch on
150 Torr
Delay15 min
- - - - - - Graphic - - - - - - - - - - - - Back - - - - - - -
page 44 of 106
Vac control
Vac control
*
MODE
Set vacuum
75 Torr
Speed
HI
Maximum
Off
DelayOff
Duration Off
- - - - - - Graphic - - - - - - - - - - - - Back - - - - - - -
1013.2
mbar
Auto mode
Function
Sensitivity normal
Speed
HI
Minimum
Off
Delay
Off
Duration
Off
- - - - - - Graphic - - - - - - - - - - - - Back - - - - - - -
*
Pump down
Vac control
Auto mode
Program
VACUULAN
Configuration
Auto mode
MODE
- - - - - - - - Back - - - - - - -
1013.2
mbar
*
Program
MODE
1013.2
mbar
*
: or automatically after
20 seconds without action
Program
Edit
Open
0
Store 0
Delay
Off
- - - - - - Graphic - - - - - - - - - - - - Back - - - - - - -
page 45 of 106
Pump down function
?Continuous pumping with pressure and time settings
? Operation on demand of a speed controlled NT VARIO / VARIO-B
pump
Preselections
?Use the selection knob to select the parameters. All parameters can
be altered even while operation control is running.
? Speed: Preselection of the motor speed for pump down. The selection ?HI? effects the maximum speed and best ultimate vacuum of the
pump (with automatic speed reduction at ultimate vacuum).
The ?Speed? is adjustable in a range of 1-100% and to ?HI?.
? Minimum: The controller switches the pump off once the preset value
for ?Minimum? has been reached.
?Minimum? is adjustable in a range of 1-795 Torr (1-1060 mbar) or can
be set to ?Off?.
A preset ?Duration? (process time) has no effect if the process is
stopped due to a preset ?Minimum? before ?Duration? is reached.
? Delay: ?Delay? determines the time the coolant valve remains open
after the process has been stopped.
The ?Delay? is adjustable in a range of 1-300 minutes or can be set to
?Off? (?Off? means that the coolant valve closes immediately when the
process stops.).
?Duration: ?Duration? determines the total process time since control
start.
The process time is adjustable between 1-1440 minutes (24 h) or can
be set to ?Off?. ?Off? indicates that no endpoint for pump down is determined.
If a ?Duration? is preset, the controller switches off the pump when the
preset process time is reached, even if a preset ?Minimum? is still not
reached.
page 46 of 106
?If neither ?Minimum? nor ?Duration? is preset, process control has to be
stopped by pressing key ?STOP?.
The screen-shot shows the factory-set values.
Pump down
760 Torr
Pump down
Speed HI
Minimum
Off
Delay
Off
Duration
Off
- - - - - - Graphic - - - - - - - - - - - - Back - - - - - - -
10 mbar
00:03:50
When selecting ?Graphic? the display shows a pressure vs. time curve.
The timeline in the diagram adapts automatically to the process time.
?Press the selection knob twice to return to the standard display.
Temporary switching from ?Pump down? to ?Vac control? or ?Auto
mode? (only if control is running):
?Press ?MODE? key. The controller switches to ?Vac control? function,
the current vacuum is used as set value.
?Pressing ?MODE? key again switches to ?Auto mode? function. The
controller adapts the boiling pressure starting from the current vacuum
level.
?The preset function of the controller does not change due to this temporary switching. When pressing ?STOP? key, the controller is set
again to the ?Pump down? function.
Adapting the pumping speed during pump down:
? Press the selection knob and turn.
? Turning the knob to the left reduces the speed.
? Turning the knob to the right increases the speed.
page 47 of 106
Vac Control function
? Vacuum control to a preset vacuum value
? Operation on demand of a speed controlled pump (NT VARIO /
VARIO-B)
Preselections
+Use the selection knob to select the parameters. All parameters can
be altered even while operation control is running.
? Set vacuum: The ?Set vacuum? is the set point for vacuum control
with pinpoint precision for NT VARIO / VARIO-B pumps.
The ?Set vacuum? is adjustable in a range of 1-795 Torr (1-1060 mbar)
or can be set to ?Turbo?. The selection ?Turbo? leads to the optimum
backing pressure for a turbomolecular pump.
? Speed: The maximum motor speed can be preselected (to control the
pumping speed).
The ?Speed? is adjustable in a range of 1-100% or can be set to ?HI?.
The selection ?HI? (recommended) provides the optimum pumping
speed of the pump and therefore an optimum ultimate vacuum.
?Maximum: An upper pressure limit can be preselected. The pump
switches off if the pressure limit is exceeded, e.g., at the end of suctions or filtrations. The pressure limit is only active once the pressure
has gone below ?Maximum?.
The ?Maximum? is adjustable in a range of 794-1Torr (1059 - 1 mbar)
(at the least 1 Torr (mbar) higher than the ?Set vacuum?) and to ?Off?.
?Off? means that no ?Maximum? value is preset.
? Delay: ?Delay? determines the time the coolant valve remains open
after the process has been stopped.
The ?Delay? is adjustable in a range of 1-300 minutes or can be set to
?Off? (?Off? means that the coolant valve closes immediately when the
process stops.).
?Duration: ?Duration? determines the total process time since control
start.
page 48 of 106
A preset ?Duration? (process time) has no effect if the process is
stopped due to a preset ?Maximum? before ?Duration? is reached.
The ?Duration? is adjustable between 1-1440 minutes (24 h) or can be
set to ?Off?. ?Off? means that no endpoint of the process is defined.
The screen-shots show the factory-set values.
Vac control
760 Torr
Vac control
Set vacuum
75 Torr (*) Speed
HI
Maximum
Off
Delay
Off
Duration
Off
- - - - - - Graphic - - - - - - - - - - - - Back - - - - - - (*) MV 2 NT VARIO,
MV 10 VARIO-B:
?Turbo?
When selecting ?Graphic? the display shows a pressure vs. time curve.
The timeline in the diagram adapts automatically to the process time.
?Press the selection knob twice to return to the standard display.
Temporarily switching from ?Vac control? to ?Auto mode? while process control is running:
?Press ?MODE? key. The controller switches to ?Auto mode? and adapts
the boiling pressure starting with the actual set value. The preset function of the controller does not change due to this switching. When
pressing the ?STOP? key, the controller is in ?Vac control? function
again.
Adjustment of the set vacuum during vacuum control:
Dynamic, interactive adaptation:
+ Press the selection knob and keep pressed.
+ Turning the knob for a 1/4 turn to the left causes pump down.
+ Turning the knob for a 1/4 turn to the right causes venting.
+ When the knob is released, the current pressure value is used as new
set value.
page 49 of 106
Alternatively:
Fine tuning:
The set vacuum can be fine-adjusted by turning the selection knob while
process is running.
+ Turn the selection knob.
+ A full turn causes a change of the set vacuum of 9 Torr (12 mbar).
+ Turning the knob one detent causes a change of the set vacuum of 1
Torr (mbar).
page 50 of 106
Auto mode
?Control of a NT VARIO / VARIO-B pump in ?Auto mode?:
Automatic detection of boiling points, and automatic adjustment
of determined boiling points as process parameters change.
Preselections
?Use the selection knob to set the parameters.
? Sensitivity: The ?Sensitivity? of the control determines the control speed.
The ?Sensitivity? is adjustable to ?high?, ?normal? or ?low?.
High sensitivity leads to a reduced pump-down speed, e.g., for small
amounts of solvents or foaming processes. Use a low sensitivity for ?noncritical? processes to reduce process time. Usually setting the ?Sensitivity? to ?normal? is appropriate.
? Speed: The maximum motor speed can be preselected (to limit the
pumping speed).
The ?Speed? is adjustable in a range of 1-100% or can be set to ?HI?.
The selection ?HI? (recommended) causes an automatic limitation of
the adaptation depending on parameters determined during the process. Only in case of very sensitive processes is it advisable to reduce
the maximum speed.
? Minimum: If the vacuum value reaches ?Minimum? the process is
stopped. Use ?Minimum? for automatic process termination.
The ?Minimum? is adjustable in a range of 2-795 Torr (2 - 1060 mbar),
or can be set to ?Auto? or to ?Off?.
When selecting ?Auto? the controller switches off automatically at the
end of the process (boiling plateau). This is recommended only for
large amounts of solvents.
? Delay: ?Delay? specifies the time the coolant valve remains open after
process stop.
The ?Delay? is adjustable in a range of 1-300 minutes or can be set to
?Off? (?Off? means that the coolant valve closes immediately when the
process stops.).
page 51 of 106
?Duration: ?Duration? determines the total process time since control
start.
The ?Duration? is adjustable between 1-1440 minutes (24 h) or can
be set to ?Off?. A preset ?Duration? (process time) has no effect, if the
process is stopped earlier by reaching the preset ?Minimum?.
The screen-shot shows the factory-set values.
Auto mode
760 Torr
Sensitivity normal
Speed
HI
Minimum
Off
Delay
Off
Duration
Off
- - - - - - Graphic - - - - - - - - - - - - Back - - - - - - -
Auto mode
50 mbar
00:07:45
When selecting ?Graphic? the display shows a pressure vs. time curve.
The timeline in the diagram adapts automatically to the process time.
?Press the selection knob twice to return to the standard display.
Temporary switching from ?Auto mode? to ?Vac control? function
?Press ?MODE? key. The controller switches to ?Vac control?. The current pressure value is used and held as new set point.
?The preset function of the controller does not change due to this temporary switching. When pressing ?STOP? key, the controller is set
again to the ?Auto mode?.
page 52 of 106
Program function
? Permits ten programs to be defined and stored, each with up to
ten program steps with preset values for vacuum and time.
?
? Edit:
Use to define the preset values for the process run:
Time: Defines either the process runtime for each program step to
reach a preset vacuum level or, if programming a ?Step?, the runtime
after having achieved the vacuum level. The total process runtime is
shown in the base line. Attention: A preset runtime of 99:59:59 hours
in the final program step will cause the process to run endlessly. Terminate the process by pressing the ?STOP? key .
Vacuum: Vacuum level to be attained.
Venting valve: Operating a venting valve to reach a preset vacuum
level.
?Step?: ?Step? causes pump down as fast as possible to the preset
vacuum level. As soon as the vacuum level is reached the time meter
starts running.
?Auto?: Auto = : indicates that the system will search for a boiling
point automatically, and will automatically adapt to changes in the boiling point until a preselected time interval expires.
Auto = : indicates that the system will automatically adapt to changes in the boiling point. The program step is finished when the selected
time or pressure value has been reached.
Selecting ?Auto? in combination with ?Step? in one program step is not
possible.
? Open: Choose program (Programs 0 - 9).
? Store: This command stores an edited program or the program of the
last process to one of the storage spaces 0 - 9.
? Delay: ?Delay? specifies the time the coolant valve remains open after
process stop.
The ?Delay? is adjustable in a range of 1-300 minutes or can be set to
?Off? (?Off? means that the coolant valve closes immediately when the
process stops.).
page 53 of 106
Editing:
+ To select row: turn and press selection knob.
+ To adjust parameter: turn the selection knob.
+ To confirm parameter: Press selection knob. Controller will accept
change and jump to the next parameter in the same row.
+ After 5 seconds without a change, the parameter is assumed to be the
current setting. Select the next row to edit or return to the Program menu.
? In case, store an edited program after having quit ?Edit? by storing it to
one of the storage spaces 0 - 9 (select ?Store?).
The screen-shot shows the factory-set values.
Program
760 Torr
Edit
Open
0
Store 0
Delay
Off
- - - - - - Graphic - - - - - - - - - - - - Back - - - - - - -
Program 5 : 4
1013mbar
1013 mbar
00:28:00
When selecting ?Graphic?, the display shows a pressure vs. time curve.
Program number, and the step number in that program, along with the
vacuum setting, the actual current pressure and the actual runtime are
displayed across the top.
The timeline in the diagram adapts automatically to the process time.
?Press the selection knob twice to return to the standard display.
The most recent process (except in ?VACUULAN? function) is stored in
the temporary data memory as long as the controller stays switched on.
This program can be transferred to a storage space and edited.
Once the program is finished, the clock symbol starts to flash. Confirm the
end of the program by pressing START/STOP (clock symbol will disappear).
Attention: If ?Autostart? is set to ?On?, the program will start again
(time will be reset to 00:00:00) after a power failure or after switching the controller off/on. Only if the end of the program (clock symbol
flashing) has been confirmed by pressing START/STOP, the program will
not start again.
page 54 of 106
Attention: If the controller is set to ?Defaults?: ?On?, all stored programs will be deleted.
Application example
Example
NT VARIO vacuum pump with speed control (e.g., with a rotary evaporator): Degassing and automatic distillation with timing
Program
No
hh:mm:ss Vac
Vent. Step
Auto
?
?
01 00:00:00 ATM ?
?
02 00:10:00 300
?
03 01:00:00 2
*
04 00:01:00 ATM ?
?
05 00:00:00 0
06 00:00:00 0
07 00:00:00 0
08 00:00:00 0
09 00:00:00 0
10 00:00:00 0
- - - - - - - - - - - - - Back - - - - - - - - - - - - - 01:11:00
* If the pressure difference
between the vacuum for
degassing and the expected vacuum for distillation is
very small (distillation vacuum >75% of the degassing vacuum), select the
function ?Auto ? (adapting
the vacuum starting from
the current pressure) instead of ??Auto ? (at first
searching the boiling point
automatically, and then
adapting the vacuum).
?
Program step 1 should be always a definite initial state, here atmospheric
pressure (ATM). To reach this state definitely, set a tickmark at ?Vent.?
and ?Step? by pressing the selection knob.
In step 2, pumping begins, attempting to reach 300 Torr/mbar as quickly
as possible (?Step?). Vacuum holds there for 10 minutes (degassing the
solvent).
In step 3, ?Auto
? causes an automatic search of a boiling point in
the pressure interval between 300 Torr/mbar/hPa (depending on preset
pressure unit) and 2 Torr/mbar/hPa, followed by automatic adaptation to
changes in the boiling point. The following step starts either (1) once the
cumulative process time reaches the set limit (1 hour/60 minutes), even
if the preset pressure (2 Torr/mbar/hPa) has not been reached, or (2) if
a vacuum of 2 Torr/mbar/hPa is reached, even if the preset time has not
been completed.
Step 4 vents to atmospheric pressure as fast as possible and switches off
the control after one minute.
page 55 of 106
VACUULAN function
?Optimizes vacuum control for vacuum networks
(e.g., VACUUBRAND VACUU?LAN)
?Permits on-demand operation of a speed-controlled pump
(NT VARIO/VARIO-B)
Preselections
?Use the selection knob to select the parameters.
? Set vacuum (the lower switch-off value): If the pressure drops below
the ?Set vacuum?, a time-meter starts to run and the motor speed is reduced. When the pressure exceeds the ?Set vacuum? pressure again,
the time meter is reset. If the ?Set vacuum? is not reached within 100
hours, the controller signals an error.
The ?Set vacuum? is adjustable in the range of 1-795 Torr (1-1060
mbar).
? Switch on (the higher switching value): If the pressure exceeds this
pressure, pumping down starts again.
The ?Switch on? pressure is adjustable in the range of 2-795 Torr (21060 mbar) (at the least 1 Torr (mbar) higher than the ?Set vacuum?).
In the event of a sudden high-pressure spike, pumping starts again
even if the ?Switch on? pressure has not been reached (pressure increase control).
? Delay: If the vacuum is below ?Set vacuum? for longer than the ?Delay?
time, the pump is stopped. Pumping starts again in the event of a rapid
pressure increase or if the ?Switch on? level is exceeded.
The ?Delay? is adjustable in a range of 1-300 minutes or can be set to
?Off? (?Off? means that the coolant valve closes immediately when the
process stops.).
page 56 of 106
This screen-shot shows the factory-set values.
VACUULAN
760 Torr
Set vacuum
19 Torr
Switch on
150 Torr
Delay15 min
- - - - - - Graphic - - - - - - - - - - - - Back - - - - - - -
VACUULAN
40 mbar
00:13:00
When selecting ?Graphic? the display shows a pressure vs. time curve.
The timeline in the diagram adapts automatically to the process time.
?Press the selection knob twice to return to the standard display.
page 57 of 106
Application examples
Assembly of a vacuum system
? Assemble vacuum connection lines between vacuum pump, CVC
3000 and vacuum application.
+Assemble the vacuum connection line between the controller and the
vacuum application, if the controller is not part of a pumping unit.
? Assemble electrical connections.
? Connect coolant if necessary.
Vacuum for filtration and suction
? Select ?Pump down? function.
?If necessary, set value for ?Speed? (high or low pumping speed). Reduce the speed in case of fast sedimentation (formation of a filter cake).
? Set ?Set vacuum? to a value which provides adequate suction but does
not lead to evaporation of the solvent.
? Start process by pressing ?START/STOP? key.
alternatively:
?Select ?Vac control? function.
? Set ?Set vacuum? to a value which does not lead to evaporation of the
solvent.
?If necessary, set value for ?Speed? (high or low pumping speed). Reduce the speed in case of fast sedimentation (formation of a filter cake).
? Set ?Maximum? pressure setting so that pump will switch off at the end
of the filtration process, or in the event that a filter cake cracks, leading
to a sudden pressure increase.
?Start process by pressing ?START/STOP? key.
?Tip for filtration: Adjust preset pressure to a value well above the
boiling pressure of the solvent (e.g., for water >>15 Torr (20 mbar)).
Set the maximum pressure to e.g., 375 Torr (500 mbar). Once the filtration has finished, the pressure increases and the pump is switched
off automatically.
page 58 of 106
Vacuum for gel dryer, drying chambers and
vacuum ?concentrators
? Select function ?Pump down? function. ?Speed? ?HI? is recommended.
For gel dryers set a lower speed if necessary (if the gels tend to crack).
?Set ?Minimum? to prevent volatile components from evaporating. The
process is stopped automatically as soon as ?Minimum? is reached.
? Set a process time (?Duration?) if necessary.
? Start process by pressing ?START/STOP? key.
alternatively:
? Select ?Vac control? function to dry at a predetermined vacuum level.
? Set ?Set vacuum? to the preferred evaporation vacuum of the solvent.
? Set a process time (?Duration?) if necessary.
? Start process by pressing ?START/STOP? key.
Vacuum for distillation and evaporation
(e.g., rotary ?evaporator)
Fully automatic determination and adaptation of the boiling point
(recommended)
?Select ?Auto mode?.
? Start process by pressing ?START/STOP? key.
? The ?Auto mode? allows a fully automatic distillation even if the boiling
vacuum is unknown. In case of solvent mixtures the vacuum is reduced
until all solvents or volatile components are evaporated (with respect
to the ultimate vacuum of the pump and the bath temperature).
? If ?Minimum? is set, the controller switches off the pump when the preset vacuum value is reached. The ?Minimum? should be well below
the boiling vacuum of the solvent to be evaporated and above the ultimate vacuum attainable in the apparatus. If the ?Minimum? is set to
?Auto? , the controller automatically switches off the pump at the end
of the evaporation (recommended for large solvent quantities only).
The setting of ?Duration? (process runtime) has no effect if the pump is
switched off due to ?Minimum? before ?Duration? is over.
page 59 of 106
? When setting a value for ?Duration? the controller switches off the
pump when ?Duration? has passed even if a preset ?Minimum? is still
not reached.
? If neither ?Minimum? nor ?Duration? is preset, pumping down has to be
finished by pressing the ?START/STOP? key.
alternatively:
Semi-automatic distillation and evaporation
? Select function ?Pump down?.
? Start process by pressing ?START/STOP? key.
? Observe process. As soon as evaporation starts, press ?MODE? key
(switching to ?Vac control?). The vacuum level is kept constant (at the
boiling pressure). Fine tuning of the vacuum value is possible by turning the selection knob.
Pressing ?MODE? key a second time switches to ?Auto mode? causing
the vacuum level to be automatically adapted to changes of the boiling
pressure.
alternatively:
? Select ?Vac control? function.
? Set a maximum ?Speed?, to select a faster or slower process.
?To set ?Maximum? is usually not necessary, unlike filtrations, because
the pressure does not increase at the end of the evaporation.
? Set a value for ?Duration? if the process should be terminated automatically after a definite time.
? Set ?Set vacuum? depending on the solvent and the temperature.
? Start process by pressing ?START? key.
?To temporarily switch to ?Auto mode?: Press ?MODE? key. The
controller switches to ?Auto mode?. The setting of the controller does
not change due to this switching. After pressing ?START/STOP? key
the controller is in ?Vac control? again.
page 60 of 106
Fore-vacuum for high vacuum pumps
Using the NT VARIO pump as fore-vacuum pump (also known as a
?roughing pump? or ?backing pump?) for a high vacuum pump (e.g. turbomolecular with high fore-vacuum tolerance):
+Use ?Pump down? function with ?Speed? set to ?HI? or
+Use ?Vac control? function with ?Set vacuum? set to ?Turbo?.
page 61 of 106
Configuration
In the ?Configuration? menu the device parameters are preselected.
After 20 seconds without action the function ?Configuration? and its submenus (except submenu ?Sensors?) are quit automatically without storing any possibly changed parameter.
Preselections
?Use the selection knob to select the parameters.
? Adjustment: Adjustment of the pressure transducer under vacuum
and/or at atmospheric pressure, see also section ?Readjustment of
VSK 3000?, pg. 63.
Adjustment to atmospheric pressure is carried out at an absolute pressure value between 795 - 525 Torr (1060 - 700 mbar). This is especially helpful in high elevation laboratories. Adjustment under vacuum
may be done at an absolute vacuum value between 0 - 15 Torr (0 - 20
mbar). In the range between 15 to 525 Torr (20 to 700 mbar) no adjustment is possible; ---- Torr is displayed.
?RS-232: Configuration of the interface, setting of parameters and commands, see section ?Interface?.
Baud rate can be set to 19200, 9600, 4800 or 2400, parity on ?8-N-1?,
?7-O-1? or ?7-E-1?, Handshake on ?no?, ?Xon-Xoff? or ?RTS-CTS? and
remote on ?On? or ?Off?.
?Sensors: Selection of the pressure transducer to be controlled (maximum 4 external sensors).
? Display: Selection of the device parameters ?Brightness? between 0
- 100%, ?Contrast? between 0 - 100%, ?Sound? ?On? or ?Off?, ?Units?
?mbar?, ?hPa? or ?Torr?, ?Language? ?German?, ?English?, ?French?,
?Italian?, ?Spanish?, ?Turkish?, ?Korean?, ?Chinese?, ?Portuguese?,
?Russian?, ?Polish?, ?Dutch?, ?Japanese?, ?Finnish?.
? Autostart: If ?Autostart? is set to ?On? the controller restarts a running
process automatically after a mains failure. If this is unwanted, set
?Autostart? to ?Off?.
Attention: If ?Autostart? is preselected, the process starts
immediately after power failure without pressing any fur-
page 62 of 106
ther key. It is the user?s responsibility to ensure that no
dangerous status of the system due to the automatic startup can occur and to provide appropriate safety measures.
If necessary, the user has to check prior to starting the
process if the option ?Autostart? is enabled.
+ Defaults: If ?Defaults? is set to ?Load?, the controller is reset to factory
set values. All stored programs and parameters are deleted.
This screen-shot shows the factory-set values.
Configuration
Adjustment
760 Torr
RS-232...
Sensors...
Display...
Autostart Off
Defaults Cancel
- - - - - - - Back - - - - - - -
page 63 of 106
Readjustment of VSK 3000
NOTICE
The vacuum gauge head was adjusted using factory standards, which are traceable through regular calibration in
an accredited laboratory (DAkkS calibration laboratory)
to the German national pressure standard. Depending on
the process and/or accuracy requirements, check the adjustment and readjust if necessary. For readjustment, the
device has to be adjusted both at atmospheric pressure
as well as under vacuum but only if the reference pressures are known with certainty. The adjustment mode can
be activated only if the process control is inactive. Press
?START/STOP? key, if necessary. In the range between 15
to 525 Torr (20 to 700 mbar) no adjustment is possible;
---- Torr is displayed.
Adjustment at atmospheric pressure
An adjustment at atmospheric pressure is only
possible if the pressure is higher than 525 Torr
1013 mbar (700 mbar).
Vent the measurement connection of the VSK
3000 and/or the vacuum system. Make sure
that the pressure transducer is at atmospheric
pressure.
?In ?Configuration? menu, select program ?Adjustment? at the controller.
? Use the selection knob to adjust the reading to the current atmospheric
pressure.
?Press the selection knob to confirm.
Note: To determine the actual atmospheric pressure, use an accurate
barometer or get accurate reading from the weather service, or a nearby
airport or other reliable source (taking into account the difference in altitude between the source and the laboratory).
page 64 of 106
Adjustment under vacuum
An adjustment under vacuum is only possible
if the pressure is lower than 15 Torr (20 mbar)
0 mbar
absolute.
Evacuate the measurement connection of
the VSK 3000 to a pressure < 0.1 Torr (mbar)
(e.g., by applying a good two-stage rotary vane
pump).
?In ?Configuration? menu, select program ?Adjustment? at the controller.
?The reading is automatically adjusted to ?zero?.
?Press the selection knob to confirm.
Note: Adjustment under vacuum with an actual pressure higher than 0.1
Torr (mbar) reduces the accuracy of the measurement. If the pressure is
significantly higher than 0.1 Torr (mbar), adjustment to a reference pressure is recommended.
Adjustment at a reference pressure
Instead of adjustment under vacuum to a pressure < 0.1 Torr (mbar), adjustment to a precise0...20 mbar ly known reference pressure within the range
of?0..... 15 Torr (20 mbar) is possible. Evacuate
the measurement connection of the VSK 3000
to a pressure within 0 ..... 15 Torr (0.....20 mbar).
?In ?Configuration? menu, select program ?Adjustment? at the controller.
?The reading is automatically adjusted to ?zero?.
?Use the selection knob to adjust the display to the reference pressure
at the vacuum line within the range of 0 ..... 15 Torr (0.....20 mbar).
?Press the selection knob to confirm.
Note: The accuracy of the value of the reference pressure will directly
affect the accuracy of the adjustment. If the nominal ultimate vacuum
of a diaphragm pump is used as reference vacuum, the accuracy of the
controller might be doubtful. The diaphragm pump may not achieve the
specified value (due to condensate, poor condition, failure of valves or
diaphragm, leaks).
page 65 of 106
Calibration in the factory
Control of measuring equipment
The VACUUBRAND DAkkS calibration laboratory is accredited by the
Deutsche Akkreditierungsstelle GmbH (national accreditation body of the
Federal Republic of Germany) for the measurable variable pressure in
the pressure range from 7.5*10-4 Torr to 975 Torr (10-3 mbar to 1300
mbar) in accordance with the general criteria for the operation of testing
laboratories defined in the DIN EN ISO/IEC 17025:2000 series of standards (accreditation number D-K-15154-01).
The DAkkS is signatory to the multilateral agreements of the European
cooperation for Accreditation (EA) and of the International Laboratory Accreditation Cooperation (ILAC) for the mutual recognition of calibration
certificates.
Rely on calibration in the VACUUBRAND calibration laboratory:
- To meet the requirements of the DIN ISO 9000ff and 10012 series of
standards regarding the calibration of inspection, measuring and test
equipment at specified intervals.
- To document that the vacuum gauges calibrated are traceable to national standards of the PTB (Physikalisch-Technische Bundesanstalt;
German national institute for science and technology and the highest
technical authority of the Federal Republic of Germany for the field of
metrology and certain sectors of safety engineering).
To order DAkkS calibration of the VSK 3000 pressure transducer,
order number: ............................................................................... 900217
page 66 of 106
Cleaning the pressure transducer
?Attention: Never use a pointed or sharp-edged tool
to clean the pressure transducer.
?Never touch the ceramic diaphragm of the pressure transducer with hard objects.
?Fill the measurement chamber with a solvent (e.g.,
benzene) and allow sufficient cleaning time. Observe
all regulations concerning usage and disposal of solvents!
?Drain the solvent and dispose of in accordance with
regulations. Repeat cleaning if necessary.
?Rinse the measurement chamber several times with
alcohol in order to remove all solvent residues.
?Allow the pressure transducer to dry.
?Readjust the pressure transducer if necessary.
Readjustment of the pressure transducer VSK 3000
See section ?Readjustment of VSK 3000?, pg. 63.
Please continue with part 2 of this manual.
Part II
page 67 of 106
Technology for Vacuum Systems
Instructions for use
Part II of II
Part II:
Interface parameters - Accessories Maintenance
MD 4 NT VARIO
MV 2 NT VARIO
MV 10 VARIO-B
Speed controlled diaphragm pumps
page 68 of 106
Contents
Part I................................................................. 1
Reset / Language selection.............................................. 8
Safety information!............................................................ 11
Important information!.........................................................................11
General information............................................................................ 13
Intended use...................................................................................... 13
Setting up and installing the equipment............................................. 14
Ambient conditions............................................................................. 17
Operating conditions.......................................................................... 17
Safety during operation...................................................................... 19
Maintenance and repair..................................................................... 21
` Important information: Equipment marking (ATEX)...................... 23
Technical data.................................................................... 25
General technical data valid for all pumps......................................... 25
Gas inlet temperatures...................................................................... 25
Wetted parts...................................................................................... 28
Abbreviations..................................................................................... 29
Pump parts........................................................................................ 29
Use and operation............................................................. 32
Installing a pump in a vacuum system............................................... 32
During operation................................................................................. 35
Shutdown & storage........................................................................... 37
Vacuum controller CVC 3000............................................................. 38
Menu guide......................................................................... 43
Pump down function......................................................... 45
Vac Control function......................................................... 47
Auto mode.......................................................................... 50
Program function............................................................... 52
Application example.......................................................................... 54
VACUULAN function......................................................... 55
Application examples....................................................... 57
Vacuum for filtration and suction....................................................... 57
Vacuum for gel dryer,
drying chambers and vacuum ?concentrators.................................... 58
Vacuum for distillation and evaporation (e.g., rotary ?evaporator) 58
Fore-vacuum for high vacuum pumps............................................... 60
page 69 of 106
Configuration..................................................................... 61
Readjustment of VSK 3000............................................... 63
Calibration in the factory.................................................. 65
Cleaning the pressure transducer................................... 66
Part II.............................................................. 67
Interface parameters......................................................... 70
Setting of the interface...................................................................... 71
Read commands ?CVC 2000?........................................................... 72
Write commands ?CVC 2000?........................................................... 73
Read commands ?CVC 3000?........................................................... 75
Write commands ?CVC 3000?........................................................... 77
Accessories....................................................................... 80
Troubleshooting................................................................ 81
Replacing diaphragms and valves.................................. 85
Cleaning and inspecting the pump heads
(MD 4 NT VARIO / MV 2 NT VARIO)................................................. 86
Replacing the diaphragm.................................................................. 88
Assembling the pump heads............................................................. 90
Cleaning and inspecting the pump heads (MV 10 VARIO-B) ?????????? 92
Replacing the diaphragm.................................................................. 94
Assembling the pump heads............................................................. 95
Replacing the valve at the distributor (outlet side)............................ 97
Assembling the connecting hoses..................................................... 97
Replacing the device fuse................................................................. 99
Notes on return to the factory........................................ 100
Warranty........................................................................... 103
Health and safety clearance form.................................. 104
EC Declaration of Conformity of the Machinery .............. 105
page 70 of 106
Interface parameters
The CVC 3000 controller is equipped with a serial interface (RS 232C,
nine-pin Sub-D-plug).
?Plug-in or remove the cable (cable RS 232C) from the interface only if
the equipment is switched off.
?The interface is not electrically isolated from the measuring circuit.
?For optimal electromagnetic compatibility assemble an interface filter
(cat. no.: 638235).
The controller is fully operable via the serial interface. Measuring results,
preselections and the status of the controller can be read at any time.
The factory-set read and write commands are completely compatible
with the VACUUBRAND CVC 2000 controller (see sections ?Read / Write
commands CVC 2000?). An extended instruction set is available using the
command ?CVC 3? (see sections ?Read / Write commands CVC 3000?).
page 71 of 106
Setting of the interface
Set the interface parameters directly at the controller CVC 3000. The factory set values are underlined.
Edit and confirm the interface parameters in the ?Configuration? menu in
?RS-232? submenu using the selection knob.
?Baud: 2400, 4800, 9600 or 19200
?Parity: 8-N-1, 7-O-1 or 7-E-1
?Handshake: Off, Xon-Xoff or RTS-CTS
?Remote: On or Off
?Timeout: Sending 1s, receiving 10s.
In remote mode (Remote On, with the ?PC symbol? in the display) all keys
at the controller are inoperable.
To return to the manual operation of the controller, set the controller to ?Remote off? in menu configuration: Switch off the controller.
Then switch the controller back on, and press the selection knob
within 2s.
?A maximum of ten commands per second is possible.
?Read commands and commands ?REMOTE?, ?CVC?, and ?STORE?
can always be sent. The sending of other write commands is only possible, if ?Remote on? is selected.
?The commands have to be written in capital letters.
?Command and parameter have to be separated by a blank.
?The string is terminated with <CR> or <LF> or <CR><LF>.
?The response of the controller is always terminated with <CR><LF>.
?Numerical values and parameters can be written without leading zeros.
?The response of the controller always includes leading zeros.
Pin assignment RS-232 C
2: RxD
3: TxD
4: DTR
5: Mass
7: RTS
8: CTS
9: +5V (Bluetooth)
page 72 of 106
Read commands ?CVC 2000?
Command
Operation
Response
Description
IN_PV_1
current pressure
XXXX mbar/
Torr/hPa
unit according to preselections
IN_PV_2
current frequency
XX.X Hz
pump speed
0XXXX
1XXXX
2XXXX
3XXXX
X0XXX
X1XXX
XX0XX
XX1XX
XXX0X
XXX1X
XXXX0
XXXX1
1XXX
X1XX
XX1X
XXX1
0XXX
1XXX
X0XX
X1XX
XX00
XX01
VACUU?LAN
continuous pumping
vacuum control without automatic
vacuum control with automatic
no coolant valve
coolant valve
no venting valve
venting valve
no automatic switch off
automatic switch off
remote operation off
remote operation on
fault at pump electronics
overpressure
maloperation mode pressure transducer
last command to interface incorrect
coolant valve closed
coolant valve open
venting valve closed
venting valve open
VACUU?LAN: inactive
VACUU?LAN: pumping down,
current pressure > selected pressure
VACUU?LAN: pumping down, time for
automatic switching off is running
VACUU?LAN: system is switched off
continuous pumping: not active
continuous pumping; active
vacuum control: not active
vacuum control:
current pressure above set vacuum
vacuum control: current pressure
equals set vacuum (?1 Torr/mbar)
vacuum control:
current pressure below set vacuum
automatic: not active
automatic: determining boiling point
automatic: adjusting boiling point
automatic: system is switched off
IN_CFG
device set
preselections
IN_ERR
error code
XX02
IN_STAT
status of
process control
XX03
XX10
XX11
XX20
XX21
XX22
XX23
XX30
XX31
XX32
XX33
page 73 of 106
Write commands ?CVC 2000?
Command
OUT_MODE
Operation
Parameter
function
1
2
3
30
31
32
Description
continuous pumping
vacuum control without automatic
vacuum control with automatic
optional: sensitivity: low
optional: sensitivity: normal
optional: sensitivity: high
unit (mbar/Torr/hPa) according to preselection; see respective function for
parameter range
unit (mbar/Torr/hPa) according to preselection; see respective function for
parameter range
OUT_SP_1
set vacuum
XXXX
OUT_SP_V
set vacuum
with venting*
XXXX
OUT_SP_2
set frequency
XX.X
motor speed in Hz (99.9 for ?HI?)
OUT_SP_3
vacuum for switch
on (VACUU?LAN)
XXXX
unit (mbar/Torr/hPa) according to preselection; see respective function for
parameter range
OUT_SP_4
delay
XX:XX
hh:mm (hours:minutes)
XXXX
unit (mbar/Torr/hPa) according to preselection; see respective function for
parameter range
XX:XX
hh:mm (hours:minutes)
OUT_SP_5
OUT_SP_6
START
STOP
REMOTE
OUT_VENT
vacuum for automatic switching
off
time for automatic
switching off
(VACUU?LAN)
starting process
control
stopping process
control
remote
operation**
driving venting
valve
1
2
termination of process control
termination of process control and storage of the current pressure as new set
point
0
1
set controller to local operation
set controller to remote operation
0
1
close venting valve (not automatically)
open venting valve (process control
stopped)
* Pressure setting with venting is only possible in ?Vac control? function
if a venting valve is connected and configured, and vacuum control is
started. The venting valve opens automatically if the actual pressure
is at least 7.5 Torr (10 mbar) below the preset pressure. Automatic
venting becomes inactive if vacuum control is stopped (by pressing
?START/STOP? or ?VENT?), a pressure value is set using the command OUT_SP_1, or if the function is changed. Activate the command
OUT_SP_V again if necessary.
page 74 of 106
** If remote operation is selected or deselected, the user has to ensure
that no dangerous status of the system can occur due to the change of
the mode of operation, and must take appropriate safety precautions,
especially if selecting remote operation interferes with a locally operated active process.
page 75 of 106
Read commands ?CVC 3000?
Command
Operation
Response
IN_PV_1
current pressure
XXXX.X mbar/Torr/hPa
IN_PV_2
current speed
XXX%
IN_PV_3
time
XX:XX h:m
IN_PV_X
pressure
XXXX.X XXXX.X ...
IN_PV_T
operation time of
the controller
XXXXdXXh
device set
preselections
0XXXXXXXXXXXXXXX
1XXXXXXXXXXXXXXX
2XXXXXXXXXXXXXXX
3XXXXXXXXXXXXXXX
4XXXXXXXXXXXXXXX
5XXXXXXXXXXXXXXX
XyXXXXXXXXXXXXXX
XX0XXXXXXXXXXXXX
XX1XXXXXXXXXXXXX
XX2XXXXXXXXXXXXX
XXX0XXXXXXXXXXXX
XXX1XXXXXXXXXXXX
XXXX0XXXXXXXXXXX
XXXX1XXXXXXXXXXX
XXXXX0XXXXXXXXXX
XXXXX1XXXXXXXXXX
XXXXXX0XXXXXXXXX
XXXXXX1XXXXXXXXX
XXXXXXX0XXXXXXXX
XXXXXXX1XXXXXXXX
XXXXXXXX0XXXXXXX
XXXXXXXX1XXXXXXX
XXXXXXXXX0XXXXXX
XXXXXXXXX1XXXXXX
XXXXXXXXXX0XXXXX
XXXXXXXXXX1XXXXX
XXXXXXXXXXX0XXXX
XXXXXXXXXXX1XXXX
XXXXXXXXXXXX0XXX
XXXXXXXXXXXX1XXX
XXXXXXXXXXXXXyXX
XXXXXXXXXXXXXXyX
XXXXXXXXXXXXXXX0
XXXXXXXXXXXXXXX1
IN_CFG
Language:
0: German
1: English
2: French
3: Italian
4: Spanish
5: Turkish
6: Korean
7: Chinese
8: Portuguese
9: Russian
A: Polish
B: Dutch
C: Japanese
D: Finnish
+
Description
unit according to preselections
1-100% or ?HI?
process runtime (hours:minutes)
pressure of all connected sensors,
unit (mbar/Torr/hPa) according to
preselections
operation time in days and hours
VACUU?LAN
Pump down
Vac control
Auto mode
Program
measuring device
y: 0......D: language+ (hexadecimal)
pressure unit mbar
pressure unit Torr
pressure unit hPa
autostart off
autostart on
acoustic signal off
acoustic signal on
VARIO pump not connected
VARIO pump connected
VMS not connected
VMS connected
in-line valve not connected
in-line valve connected
coolant valve not connected
coolant valve connected
venting valve not connected
venting valve connected
fault indicator not connected
fault indicator connected
level sensor not connected
level sensor connected
remote module not connected
remote module connected
y: 1......9: sensor number
y: 1......9: sensor quantity
remote operation off
remote operation on
page 76 of 106
Command
IN_STAT
Operation
status process
control
Response
0XXXXX
1XXXXX
X0XXXX
X1XXXX
XX0XXX
XX1XXX
XXX0XX
XXX1XX
XXXX0X
XXXX1X
XXXX2X
XXXX3X
XXXX4X
XXXX5X
XXXXX0
XXXXX1
XXXXX2
XXXXX3
IN_ERR
fault status
0XXXXXXXX
1XXXXXXXX
X0XXXXXXX
X1XXXXXXX
XX0XXXXXX
XX1XXXXXX
XXX0XXXXX
XXX1XXXXX
XXXX0XXXX
XXXX1XXXX
XXXXX0XXX
XXXXX1XXX
XXXXXX0XX
XXXXXX1XX
XXXXXXX0X
XXXXXXX1X
XXXXXXXX0
XXXXXXXX1
IN_SP_1
set vacuum
XXXX mbar/Torr/hPa
IN_SP_2
maximum speed
XXX%
IN_SP_3
switching
pressure
XXXX mbar/Torr/hPa
Description
pump off
pump on
in-line valve closed
in-line valve open
coolant valve closed
coolant valve open
venting valve closed
venting valve open
VACUU?LAN
Pump down
Vac control
Auto mode
Program
measuring device
control off
pump down determining boiling point
set vacuum reached boiling pressure found
current pressure below set vacuum
- automatic switch-off
no fault at pump
fault at pump
no fault at in-line valve
fault at in-line valve
no fault at coolant valve
fault at coolant valve
no fault at venting valve
fault at venting valve
no overpressure
overpressure
no fault at pressure transducer
fault at pressure transducer
catchpot not full
catchpot full
no external fault
external fault
last interface command correct
last interface command incorrect
unit according to preselections
speed in % (1-100% or ?HI?)
switching pressure for VACUU?LAN
or two point control;
unit according to preselections
page 77 of 106
Command
Operation
Response
Description
IN_SP_4
delay
XX:XX h:m
IN_SP_5
switch off
pressure
XXXX mbar/Torr/hPa
IN_SP_6
runtime
XX:XX h:m
IN_SP_P1y
time
XX:XX:XX h:m:s
IN_SP_P2y
pressure
XXXX mbar/Torr/hPa
hours:minutes (00:00 = Off)
?Maximum? for ?Vac control?,
?Minimum? for ?Pump down?)
unit according to preselections
process runtime (hours:minutes)
time in program step y (0......9)
(hours:minutes:seconds)
0
pressure in program step y (0......9)
unit according to preselections
no venting valve in program step y
(0......9)
venting valve in program step y
(0.....9)
IN_SP_P3y
venting valve
IN_SP_P4y
Step
0
1
no ?Step? in program step y (0.....9)
?Step? in program step y (0......9)
IN_SP_P5y
Auto
0
1
no ?Auto? in program step y (0.....9)
?Auto? in program step y (0......9)
current pressure
of pressure transducer x
XXXX mbar/hPa/Torr
pressure of pressure transducer x
(order of numbering according to
display in ?Sensors? menu)
version
CVC 3000 VX.XX
IN_PV_Sx
IN_VER
1
software version
Write commands ?CVC 3000?
Command
OUT_MODE
OUT_CFG
Operation
function
configuration
(bus monitoring)
Parameter
0
1
2
3
30
31
32
4
yXXX
X0XX
X1XX
X2XX
XX0X
XX1X
XXX0
XXX1
Description
VACUU?LAN
Pump down
Vac control
Auto mode
optional: sensitivity: low
optional: sensitivity: normal
optional: sensitivity: high
Program
y: 0......D: language+ (hexadecimal), see
?Read commands CVC 3000?
pressure unit mbar
pressure unit Torr
pressure unit hPa
Autostart off
Autostart on
acoustic signal off
acoustic signal on
Attention (OUT_MODE): If control is running, it is only possible to switch either from 1 to 2, or
from 2 to 3, or from 3 to 2. The set vacuum is adopted in each case.
page 78 of 106
Command
Operation
Parameter
OUT-SP_1
set vacuum
XXXX
OUT_SP_V
set vacuum with
venting
XXXX
OUT_SP_2
speed
XXX
OUT_SP_3
start-up pressure
XXXX
unit according to preselection; see respective function for parameter range
OUT_SP_4
delay
XX:XX
hh:mm (hours:minutes)
OUT_SP_5
switch-off
pressure
XXXX
unit according to preselection; see respective function for parameter range
OUT_SP_6
switch-off time
XX:XX
hh:mm (hours:minutes)
OUT_SP_PL
open program
X
program 0......9
OUT_SP_PS
store program
X
program 0......9
OUT_SP_P1y
time
XX:XX:XX
+XX:XX:XX
OUT_SP_P2y
pressure
XXXX
OUT_SP_P3y
venting valve
0
1
no venting valve in program step y (0...9)
venting valve in program step y (0......9)
OUT_SP_P4y
Step
0
1
no ?Step? in program step y (0.....9)
?Step? in program step y (0......9)
OUT_SP_P5y
Auto
0
1
2
no ?Auto? in program step y (0.....9)
?Auto ? in program step y (0......9)
?Auto ? in program step y (0......9)
unit according to preselection; see respective function for parameter range
unit according to preselection; see respective function for parameter range
speed in % or ?HI?
total runtime until program step y
(0.....9) or time for program step y
(0.....9) (additive)
pressure at program step y (0......9)
unit according to preselection
?
START
Description
started
STOP
0
1
2
Stop and delete fault
Stop
Stop and adopt the set vacuum
REMOTE*
0
1
Remote off
Remote on
0
1
Echo off
Echo on,
write command with return value
2
3
CVC 2000 commands
CVC 3000 commands***
0
1
2
venting valve closed
venting valve open
venting until atmospheric pressure
(788 Torr (1050 mbar) at maximum)
ECHO**
CVC
OUT_VENT
STORE
store settings permanently,
if ?ECHO = 1? after realization
page 79 of 106
Command
OUT_SENSOR
Operation
Parameter
1
2...9
Description
internal sensor
external sensors (if connected)
* If remote operation is selected or deselected, the user has to ensure
that no dangerous status of the system can occur due to the change of
the mode of operation, and must also take appropriate safety precautions, especially if selecting remote operation interferes with a locally
operated active process.
** With command ?ECHO 1? a return value can be activated at write commands. A return value is only given if the command is performed correctly.
***After being switched on, the controller is in ?CVC 2? mode by default.
Send ?CVC 3? and ?STORE? to permanently set the controller RS 232C
commands to the extended set ?CVC 3000?.
page 80 of 106
Accessories
External pressure transducer VSK 3000,
capacitive Al2O3 sensor 1060-0.1 mbar........................................................636657
Coolant valve VKW-B, 24 V=.......................................................................674220
Venting valve VBM-B / KF 16 or hose nozzle 10/6 mm, 24 V= ...................674217
Adapter KF DN 16 to hose nozzle 1/2?........................................................636004
Y-type adapter VACUU?BUS........................................................................636656
Wall bushing VACUU?BUS...........................................................................636153
Extension cable VACUU?BUS, 2m...............................................................612552
Cable RS 232C, 9-pole, Sub-D.....................................................................637837
Installation set CVC 3000 (clips and screws)??????????????????????????????????????????????636593
Conversion of VACUUBRAND valves with DIN plug to
VACUUBRAND valves with VACUU?BUS plug:
VACUUBRAND-valve with DIN
plug
Conversion kit valve cable with
VACUU?BUS plug
Coolant valve VKW, 24 V= (676013)
612567
Venting valve VBM, 24 V= (666817)
612554
Vacuum distribution:
VCL-B 11
VCL 02
VCL-B 10
The VACUU?LAN? modules allow process-oriented, flexible and cost effective connections
according to your requirements. One vacuum
pump can support several workstations. Contact VACUUBRAND for details.
VCL 01
VACUU?LAN? manual flow control module VCL 01??????????????????????????????????677106
VACUU?LAN? shut off / manual flow control module VCL?02..................677107
VACUU?LAN? automatic control module VCL-B 10??????????????????????????????????677208
VACUU?LAN? manual flow control/
automatic control module VCL-B 11...........................................................677209
On this page we offer only a small selection of VACUU?LAN? options. Please contact VACUUBRAND for further
information. Listed modules are designed for surface-mounted installation. Different catalog numbers are used for
modules designed for flush-mounting with concealed tubing.
For additional accessories such as vacuum valves, small-flange components,
vacuum gauges or vacuum controllers refer to ?www.vacuubrand.com.
page 81 of 106
Troubleshooting
Fault
Possible cause
Remedy
? No display.
? Electrical power cord
not plugged in, electrical supply failure?
? Plug in power cord.
Check fuse.
? Device fuse blown?
? Identify cause of failure.
Replace device fuse.
? Controller CVC 3000
? Switch on controller and/
or pump NT VARIO /
or pump.
VARIO-B switched off?
? VACUU ? BUS cable ? Plug in VACUU ? BUS
between pump and
cable at CVC 3000 concontroller not plugged
troller.
in at controller?
? Other than above men- ? Contact local distributor.
tioned causes?
? Display disappears. ? Too much load (e.g.,
valves) connected?
? Check current draw of the
connected devices.
? Short circuit at connect- ? Replace valves.
ed valves?
? Short circuit at the
RS 232 plug?
? Check plug and cable.
? Other than above men- ? Contact local distributor.
tioned causes?
? Pressure reading
incorrect.
? Pressure transducer
decalibrated?
? Readjust VSK 3000.
? Humidity in the measurement chamber?
? Let the pressure transducer dry, e.g., by pumping. Readjust if necessary. Determine and
eliminate the cause for
humidity.
? Pressure transducer
contaminated?
? See ?Cleaning the pressure transducer?.
? Other than above men- ? Contact local distributor.
tioned causes?
? Digital pressure
reading is flashing, display shows
?0.0?.
? Pressure transducer
not correctly adjusted
under vacuum?
? Adjust VSK 3000 correctly.
page 82 of 106
Fault
Possible cause
Remedy
? No digital pressure ? Pressure transducer
reading.
defective?
? Contact local distributor.
? Digital pressure
? Overpressure at the
reading is flashing,
pressure transducer,
one blip*.
pressure > 795 Torr
(1060 mbar)?
? Release pressure immediately (risk of bursting).
? Warning triangle
and black valve
symbol are flashing, two blips*.
? External venting valve
removed or defective?
? Connect valve or replace
with a new one or reconfigure without valve.
? Warning triangle
and valve symbol
are flashing, three
blips*.
? NT VARIO / VARIO-B ? Disconnect in-line valve;
pump and in-line valve
switch controller off/on to
connected?
reconfigure.
? Warning triangle
and coolant valve
symbol are flashing, four blips*.
? Coolant valve removed ? Check connection cable
or defective?
of the valve; or use new
valve or reconfigure without valve.
? Warning triangle
and pump symbol
are flashing, six
blips*.
? NT VARIO / VARIO? Remove VMS. Restart
B pump and VMS**
controller.
(Vacuum Management
System) connected?
? Fault at the NT VARIO / ? Check pump, restart conVARIO-B pump?
troller.
? Clock symbol is
flashing.
? Preselected process
time is over?
? Confirm by pressing key
START/STOP.
? Venting valve does ? Venting valve contami- ? Clean valve.
not respond, valve
nated?
symbol is displayed.
? ?Vac control? func- ? Preset maximum pres- ? Confirm by pressing key
tion: Control stops,
sure exceeded?
START/STOP. Change
?arrow up? is flashmaximum pressure value
ing.
if necessary.
? ?Pump down? func- ? Pressure below preset ? Confirm by pressing key
tion: Control stops,
minimum pressure?
START/STOP. Change
?arrow down? is
minimum pressure value
flashing.
if necessary.
? Controller does
not respond when
pressing keys (except ON/OFF).
PC symbol is displayed.
? Controller in remote
mode?
? Control CVC 3000 via interface or switch off remote mode.
page 83 of 106
Fault
Possible cause
? Controller does
not respond when
operating any keys.
No change after
switching off/on.
Remedy
? Contact local distributor.
? Pump does not
? Pump has been ex? Allow pump to run for
start or stops imposed to condensate?
some minutes at maximediately. Warning
mum speed with atmotriangle and pump
spheric pressure at the
symbol are flashinlet.
ing.
? Overpressure in outlet
line?
? Remove blockage in line,
open valve.
? Motor overloaded?
? Allow motor to cool down,
identify and eliminate
cause of failure. Manual
reset is necessary. Switch
off pump or unplug.
? Pump does not
? Centring ring at small ? Check pump directly
achieve its ultimate
flange connection not
- connect VSK 3000 divacuum or usual
correctly positioned, or
rectly at pump inlet - then
pumping speed.
leak in the pipeline or
check connection, pipevacuum system?
line and vacuum system if
necessary.
? Wrong setting at controller?
? Select function ?Pump
down? with speed set to
?HI? and check again.
? Long, narrow vacuum
line?
? Use lines with larger diameter, length as short as
possible.
? Pump has been exposed to condensate?
? Allow pump to run for
some minutes with atmospheric pressure at the
inlet to purge.
? Clean and inspect the
pump heads.
? Deposits have been
formed inside the
pump?
? Diaphragms or valves
damaged?
? Replace diaphragms and/
or valves.
? Outgassing substances ? Check process parameor vapor generated in
ters.
the process?
page 84 of 106
Fault
Possible cause
? Pump does not
? Pressure below ?Miniachieve its ultimate
mum? in Auto mode?
vacuum or usual
pumping speed.
? Pump too noisy.
Remedy
? Change switch off pressure (?Minimum?) if necessary.
? Pump too hot?
? Allow pump to cool down.
Determine and eliminate
the cause of overheating.
? Atmospheric or high
pressure at the pump
inlet?
? Connect hose or silencer
to pump outlet. Be careful
not to cause outlet overpressure, especially with
condensable vapors.
? Diaphragm crack or
diaphragm clamping
disc loose?
? Perform maintenance.
? Other than above men- ? Contact local distributor.
tioned causes?
? Pump seized.
? Contact local distributor.
* only if ?Sound? ?On? is selected
** VMS: Vacuum management system to switch non-VARIO pumps
?A service manual with exploded view drawings, spare parts list and
directions for repair is available on request.
?The service manual is intended for trained service people only.
page 85 of 106
Replacing diaphragms and valves
?Please read section ?Replacing diaphragms and valves? completely before starting maintenance.
The pictures may show other versions of pumps. This does not change
the method of replacing diaphragms and valves.
?Never operate the pump if covers or other parts of
the pump are disassembled.
?Before starting maintenance, disconnect the electrical power cord. Wait two minutes after isolating the
equipment from AC power to allow the capacitors to
discharge.
? Ensure that the pump cannot be operated ?accidentally.
?Note: The pump might be contaminated with the process chemicals that have been pumped during operation. Ensure that the pump is decontaminated before
maintenance.
?Avoid the release of pollutants.
+Never operate a defective or damaged pump.
+Take adequate precautions to protect people from the
effects of dangerous substances that may have contaminated the pump and may be released upon disassembly. Ensure that the maintenance technician is
familiar with the safety procedures which relate to the
products processed by the pumping system.
Use appropriate protective clothing, safety goggles
and protective gloves.
+ Allow sufficient cooling of the pump before starting
maintenance.
+ Vent the pump and isolate it from the vacuum system before you start maintenance.
page 86 of 106
NOTICE
Ensure that maintenance is done only by suitably
trained and supervised technicians.
The valves and diaphragms are wear parts. If the rated
ultimate vacuum is no longer achieved or in case of increased noise level, the pump interior, the diaphragms
and the valves must be cleaned and the diaphragms and
valves must be checked for cracks or other damage.
All bearings are encapsulated and are filled with long-life
lubricant. Under normal operating conditions, the drive
system is maintenance free.
In demanding circumstances, it may be efficient to check
and clean the pump heads on a regular basis. In normal
use, the lifetime of the diaphragms and valves is typically
15,000 operating hours.
- Prevent internal condensation, transfer of liquids or
dust. The diaphragms and valves will be damaged if
liquid is pumped in significant amount.
- Carry out maintenance frequently if the pump is exposed to corrosive media or in case of deposits.
- Regular maintenance will improve the lifetime of the
pump and also protect both users and the environment.
Service kit for MD 4 NT VARIO / MV 2 NT VARIO??????????????????????????????????????696861
Service kit for MV 10 VARIO-B.....................................................................696827
Diaphragm key (width 66 mm) ...................................................................636554
Cleaning and inspecting the pump heads
(MD 4 NT VARIO / MV 2 NT VARIO)
Tools required (metric):
- 5 mm wide Allen key
- Diaphragm key width 66 mm
page 87 of 106
?Lay the pump on its side. Support the pump appropriately.
?Service only one side of the pump at a time to avoid the mixing of
parts.
View of the disassembled pump head parts
(fig.: MD 4 NT VARIO)
H
B
I
C
1
A
D
E
F
G
K
Pump head parts:
A:Housing cover
B:O-rings
C:Valves
D:Head cover
E:Diaphragm clamping disc
with square head screw
F:Diaphragm
G:Diaphragm support disc
H:Washer
I: Connecting rod
J:Housing
K:Connecting tube with O-ring
J
page 88 of 106
? Disassemble the housing cover (A) to check
the valves (C).
?Unscrew eight Allen screws with a 5mm
wide Allen key. Remove the housing cover
(A) together with head cover (D), valves (C)
and O-rings (B).
?Never use a pointed or sharp-edged tool to remove parts (e.g., screwdriver). We recommend to use a rubber mallet or compressed air (to
be blown carefully into port).
? Remove the head cover (D) carefully from the housing cover (A). Note
position and alignment of valves (C). Remove the valves.
?Replace valves or O-rings if necessary.
?Use petroleum ether or other industrial solvent to remove deposits. Do
not inhale vapors.
?Underneath the pump there is a connecting tube (K) between the two
housing covers. The connecting tube is merely stuck into the housing
covers and sealed with seal rings at the connecting tube?s ends. If the
housing cover is removed, the connecting tube becomes detached as
well.
Replacing the diaphragm
+Check diaphragm (F) for damage and replace if necessary.
?Lift diaphragm carefully sidewise.
+Never use a pointed or sharp-edged tool to
E
lift the diaphragm.
F
? Use the diaphragm key to grip the diaphragm
support disc (G) below the diaphragm.
?Unscrew diaphragm support disc (G) with diaphragm (F) and diaphragm clamping disc (E).
?Check for washers (H) between the diaphragm support disc (G) and
the connecting rod (I). Do not mix the washers from the different pump
heads, since these are set at the factory to ensure proper pump performance. Make sure that the original number is reassembled at the
individual pump head.
page 89 of 106
?Too few washers: The pump will not attain vacuum specification. Too
many washers: Diaphragm clamping disc will hit head cover, causing
noisy operation and possibly causing the pump to seize up.
?If the old diaphragm is difficult to separate from the diaphragm support
disc, immerse assembly in naphtha or petroleum ether. Do not inhale
vapors!
?Position new diaphragm (F) between diaphragm clamping disc with square head
screw (E) and diaphragm support disc (G).
?Note: This is a double diaphragm consistE
ing of two single diaphragms! Put the two
G
diaphragms together with the printed sides
outwards.
?Make sure that the square head screw of the diaphragm clamping disc
is correctly seated in the guide hole of the diaphragm support disc.
?Lift the diaphragm at the side. Place the diaphragm carefully together
with diaphragm clamping disc and diaphragm support disc in the diaphragm key.
?Avoid damage of the diaphragm: Do not excessively bend or crease
the diaphragm.
F
E
F
+Assemble the original number of washers
(H) between diaphragm support disc (G)
and connecting rod (I).
?Screw diaphragm clamping disc (E), diaphragm (F), diaphragm support disc (G),
and washers (H) to connecting rod (I).
?Optimum torque for the diaphragm support disc: 4.4 ft.lbf (6 Nm), it is
recommended to use a torque wrench. Attach torque wrench to diaphragm key (hexagonal bolt 6 mm wide).
Note: Never use the diaphragm key with any additional tools like tongs
or Allen keys without appropriate torque limitation.
page 90 of 106
Assembling the pump heads
?Bring the diaphragms (F) into a position, in
which they are in contact with the housing
(J) and centered with respect to the bore.
(K)
?Put on head covers (D).
+ Pay attention to the correct orientation of the
head covers: Align the nib at the head cover
(D) with the notch of the housing cover (A).
?Make sure that the diaphragm stays cen(1)
tered with respect to the bore so that it will
become clamped uniformly between housing (J) and head cover (D).
?Put the valves (C) an O-rings (B) in place. See figure for the correct
position of the valves:
Inlet side of pump head: The valve tongue points at the kidney-shaped
orifice in the valve seat (1).
Outlet side of pump head: The valve is oriented the same direction as
the valve at the inlet side.
?Put on housing cover (A).
?If it is not possible to position the housing cover, check the head covers for correct orientation. The nib at the head cover has to lock into
the notch of the housing cover.
? Install the connecting tube (K) under the pump between the two housing
covers. Pay attention to the correct positions of the seal rings (replace
if damaged) in the grooves at the ends of the tube. Fit the connecting
tube in the bore of the housing cover. After assembly the connecting
tube may have some play.
?Screw in the Allen head screws at the head
covers diagonally at first slightly with a 5
mm wide Allen key, then tighten.
?Recommended torque: 8.9 ft.lbf (12 Nm).
page 91 of 106
Replace diaphragms and valves of the opposite side of
the pump in the same way!
Checking the ultimate vacuum
? After any intervention at the equipment (e.g., repair / maintenance)
the ultimate vacuum of the pump has to be checked. Only if the pump
achieves its specified ultimate vacuum, the pump?s leak rate is low
enough to ensure that no explosive atmospheres will occur in the interior of the equipment.
After any intervention at the vacuum sensor the leak rate of the equipment has to be checked.
If the pump does not achieve the ultimate vacuum:
- Whenever the diaphragms and valves have been replaced, a break-in
period of several hours is required before the pump achieves its ultimate vacuum.
- In case of an unusual noise, switch off pump immediately and check
clamping disc positions.
If the specified ultimate vacuum is not achieved, and if this does not
change after the break-in period:
If necessary recheck valve seats and pump chambers.
page 92 of 106
Cleaning and inspecting the pump heads (MV 10 VARIO-B)
Tools required (metric):
-
-
-
-
Phillips screw driver size 2
Open-ended wrench w/f 15/17/20
5 mm wide Allen key
Diaphragm key width 66 mm
View of the disassembled pump head parts
N
O
P
C
L
M
Q
H
G
F
J
I
R
E
D
C
B
A
Pump head parts:
A:Housing cover
B:O-rings
C:Valves
D:Head cover
E:Diaphragm clamping disc
with square head screw
F:Diaphragm
G:Diaphragm support disc
H:Washer
I: Connecting rod
J:Housing
L: Cover plate (only at outlet)
M: Countersunk screw
N: Union nut
O: Connecting hose
P: Distributor
Q: Fitting
R: Curved connecting hose
page 93 of 106
?Loosen the union nuts (N) of the hose connections at the pump heads with an openended wrench (w/f 15).
?Loosen the fittings (Q) at the pump heads
with an open-ended wrench (w/f 17).
?Turn the fittings (Q) with an open-ended
wrench (w/f 20) to detach the hoses from
the pump heads.
+Pull off the one curved connecting hose (R)
at the outlet side of the pump directly at the
pump head.
? Disassemble the housing cover (A) to check
the valves (C).
? Unscrew four Allen screws with a 5mm wide
Allen key. Remove the housing cover (A) together with head cover (D), valves (C) and
O-rings (B).
?Never use a pointed or sharp-edged tool to remove parts (e.g., screwdriver). We recommend to use a rubber mallet or compressed air (to
be blown carefully into port).
? Remove the head cover (D) carefully from the housing cover (A). Note
position and alignment of valves (C). Remove the valves.
?Replace valves or O-rings if necessary.
?Use petroleum ether or other industrial solvent to remove deposits. Do
not inhale vapors.
page 94 of 106
Replacing the diaphragm
?Remove the punched part in the centre of the new diaphragm when
replacing a diaphragm with square hole (see below).
+
+Check diaphragm (F) for damage and replace if necessary.
?Lift diaphragm carefully sidewise.
+Never use a pointed or sharp-edged tool to
lift the diaphragm.
? Use the diaphragm key to grip the diaphragm
support disc (G) below the diaphragm.
?Unscrew diaphragm support disc (G) with diaphragm (F) and diaphragm clamping disc (E).
?Check for washers (H) between the diaphragm support disc (G) and
the connecting rod (I). Do not mix the washers from the different pump
heads, since these are set at the factory to ensure proper pump performance. Make sure that the original number is reassembled at the
individual pump head.
?Too few washers: The pump will not attain vacuum specification. Too
many washers: Diaphragm clamping disc will hit head cover, causing
noisy operation and possibly causing the pump to seize up.
?If the old diaphragm is difficult to separate from the diaphragm support
disc, immerse assembly in naphtha or petroleum ether. Do not inhale
vapors!
page 95 of 106
?Position new diaphragm (F) between diaphragm clamping disc with square head
screw (E) and diaphragm support disc (G).
?Note: This is a double diaphragm consistE
ing of two single diaphragms! Put the two
G
diaphragms together with the printed sides
outwards.
?Make sure that the square head screw of the diaphragm clamping disc
is correctly seated in the guide hole of the diaphragm support disc.
?Lift the diaphragm at the side. Place the diaphragm carefully together
with diaphragm clamping disc and diaphragm support disc in the diaphragm key.
?Avoid damage of the diaphragm: Do not excessively bend or crease
the diaphragm.
F
F
E
+Assemble the original number of washers
(H) between diaphragm support disc (G)
and connecting rod (I).
?Screw diaphragm clamping disc (E), diaphragm (F), diaphragm support disc (G),
and washers (H) to connecting rod (I).
?Optimum torque for the diaphragm support disc: 4.4 ft.lbf (6 Nm), it is
recommended to use a torque wrench. Attach Allen key to diaphragm
key (hexagonal bolt 6 mm wide).
Note: Never use the diaphragm key with any additional tools like tongs
or Allen keys without appropriate torque limitation.
Assembling the pump heads
? Bring the diaphragm (F) into a position, in which it is in contact with the
housing (J) and centered with respect to the bore.
page 96 of 106
?Put on head cover (D).
+Pay attention to the correct orientation of the head covers: Align the
nib at the head cover (D) with the notch of the housing cover (A).
?Make sure that the diaphragm stays centered with respect to the bore
so that it will become clamped uniformly between housing (J) and head
cover (D).
(1)
?Put the valves (C) an O-rings (B) in place.
See figure for the correct position of the
valves:
Inlet side of pump head: The valve tongue
points at the kidney-shaped orifice in the
valve seat (1).
Outlet side of pump head: The valve is oriented the same direction as the valve at the
inlet side.
?Screw in the Allen head screws at the head
covers diagonally at first slightly with a 5
mm wide Allen key, then tighten.
?Recommended torque: 8.9 ft.lbf (12 Nm).
Individual performance check of a pump head:
Check the performance of an individual pump head by measuring the
vacuum at its inlet port.
Use a suitable vacuum gauge (e.g., DVR 2) and make sure that it is correctly calibrated. A vacuum of less than 82 Torr (110 mbar) should be
indicated.
+If the reading is higher than 82 Torr (110 mbar), recheck the pump
chamber. Make sure that the valves and the diaphragms are correctly
seated (diaphragms concentric with bore).
Check all eight pump heads in the same way, and replace
diaphragms and valves as necessary!
page 97 of 106
Replacing the valve at the distributor (outlet side)
?Loosen the union nut of the curved connecting hose (R) running directly to the cover plate (L) of the distributor (P) with an open-ended
wrench (w/f) 15. Loosen only the union nut at the pump head, not the
one at the distributor.
+Pull off the curved connecting hose at the pump head.
?Unscrew the two countersunk head screws
(M) at the cover plate (L) with an Phillips
screw driver. Remove cover plate.
M
B
? Note the position and orientation of the valve
(B) and remove.
+Check valve for damage and replace if necessary. Make sure that the valve is correctly
seated.
?Reassemble cover plate (L) and secure with
countersunk screws (M).
Assembling the connecting hoses
? Slip the connecting hoses (O) onto the hose
connectors by turning the fittings (Q) with
an open-ended wrench w/f 20.
+Mount the one curved connecting hose (R)
at the outlet side of the pump directly at the
pump head.
?Tighten the fittings (Q) at the pump heads
with an open-ended wrench w/f 17.
page 98 of 106
?Tighten the union nuts (N) of the hose connections at the pump heads with an openended wrench w/f 15.
Checking the ultimate vacuum
? After any intervention at the equipment (e.g., repair / maintenance)
the ultimate vacuum of the pump has to be checked. Only if the pump
achieves its specified ultimate vacuum, the pump?s leak rate is low
enough to ensure that no explosive atmospheres will occur in the interior of the equipment.
After any intervention at the vacuum sensor the leak rate of the equipment has to be checked.
If the pump does not achieve the ultimate vacuum:
- Whenever the diaphragms and valves have been replaced, a break-in
period of several hours is required before the pump achieves its ultimate vacuum.
- In case of an unusual noise, switch off pump immediately and check
clamping disc positions.
If the specified ultimate vacuum is not achieved, and if this does not
change after the break-in period:
Check hose connectors at pump heads for leaks. If necessary recheck
valve seats and pump chambers.
page 99 of 106
Replacing the device fuse
?Switch off the pump.
?Disconnect the electrical power cord before unscrewing the fuse holder.
Identify and eliminate the cause of failure before switching on the pump again.
fuse holder
MD 4 NT VARIO /
MV 2 NT VARIO
MV 10 VARIO-B
?Unscrew the fuse holder using a slotted screw driver.
?Replace the defective fuse by a fuse of the same type (see ?Technical
data?, pg. 25). Reassemble holder with fuse to the pump.
page 100 of 106
Notes on return to the factory
Repair - return - DAkkS calibration
NOTICE
Safety and health of our staff, laws and regulations regarding the handling of dangerous goods, occupational
health and safety regulations and regulations regarding safe disposal of waste require that for all pumps and
other products, the ?Health and safety clearance form?,
pg. 104, must be sent to our office fully completed and
signed before any equipment is shipped to the authorized
service center.
Fax or mail a completed copy of the health and safety
clearance form to us in advance. The declaration must arrive before the equipment. Enclose a second completed
copy with the product. If the equipment is contaminated,
you must notify the carrier.
No repair / DAkkS calibration is possible unless the
correctly completed form is returned. Inevitably, there
will be a delay in processing the equipment if information is missing, or if this procedure is not followed.
If the product has come in contact with chemicals, radioactive substances or other substances dangerous to health
or environment, the product must be decontaminated prior to sending it back to the service center.
- Return the product to us disassembled and cleaned
and accompanied by a certificate verifying decontamination or
- Contact an industrial cleaning and decontamination
service directly or
- Authorize us to send the product to an industrial cleaning facility at your expense.
To expedite repair and to reduce costs, please enclose a
detailed description of the problem and the product?s operating conditions with every product returned for repair.
page 101 of 106
We submit repair quotations only on request and always
at the customer?s expense. If an order is placed, the costs
incurred for problem diagnosis are offset from the costs
for repair or from the purchase price, if the customer prefers to buy a new product instead of repairing the defective one.
- If you do not wish a repair on the basis of our quotation, the equipment may be returned to you disassembled and at your expense.
In many cases, the components must be cleaned in the
factory prior to repair.
For cleaning we use an environmentally friendly waterbased process. Unfortunately the combined attack of elevated temperature, cleaning agent, ultrasonic treatment
and mechanical stress (from pressurized water) may result in damage to the paint. Please mark in the health and
safety clearance form if you wish a repaint at your expense just in case such a damage should occur.
We will also replace parts for cosmetic reasons at your
request and at your expense.
NOTICE
Before returning the equipment, ensure that (if applicable):
- Oil sealed pumps: Oil has been drained and an adequate quantity of fresh oil has been filled in to protect
against corrosion. Dispose according to regulations.
- Equipment has been cleaned and/or decontaminated
(inside and outside).
- All inlet and outlet ports have been capped.
- Equipment has been properly packed, (if necessary,
please order original packaging materials at your cost),
marked appropriately and the carrier has been notified
of any possible contamination.
- The completed health and safety clearance form is enclosed.
We thank you in advance for your understanding of the
necessity for these measures that protect our employees,
and ensure that your pump is protected in shipment.
page 102 of 106
Scrapping and waste disposal:
Dispose of the equipment and any components removed
from it safely in accordance with all local and national
safety and environmental requirements. Particular care
must be taken with components and waste oil which have
been contaminated with dangerous substances from your
processes. Do not incinerate fluoroelastomer seals and
O-rings.
- You may authorize us to dispose of the equipment at
your expense.
page 103 of 106
Warranty
VACUUBRAND shall be liable for insuring that this product, including any agreed installation, has been free of defects at the time of the transfer of risk.
VACUUBRAND shall not be liable for the consequences
of improper handling, use, servicing or operation of this
product or the consequences of normal wear and tear of
wearing parts such as diaphragms, seals, valves, vanes,
condensers, oil and the breakage of glass or ceramic
parts, for the consequences of chemical, electrochemical
or electrical influences or the failure to follow the instructions in this manual.
Claims for defects against VACUUBRAND shall be limited
to one year from delivery. The same shall apply to claims
for damages irrespective of legal grounds.
For further information on general terms and conditions
refer to www.vacuubrand.com.
page 104 of 106
Health and safety clearance form
Devices will not be accepted for any handling before we have received this declaration.
Please read and comply with ?Notes on return to the factory?.
Oil filled pumps: Drain oil prior to shipping absolutely!
1. Device (Model): ................................................................... 2. Serial no.: .........................................
3. Reason for return / malfunction:
..............................................................................................................................................................
4. Has the device been used in a copper process step (e.g., semiconductor production).
? yes ? no
5. Substances (gases, liquids, solids) in contact with the device / which have been pumped:
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
..............................................................................................................................................................
6. Prior to return to the factory the device has been decontaminated.
? yes ? no
Description of the decontamination method and the test / verification procedure:
..............................................................................................................................................................
..............................................................................................................................................................
7. The device is free of hazardous, harmful substances.
? yes ? no
8. Protective measures required for VACUUBRAND employees:
..............................................................................................................................................................
9. If the paint is damaged, we wish a repaint or a replacement of parts for reason of appearance (repaint
and replacement at customer?s expense). ? yes ? no
10.Legally binding declaration
We assure for the returned device that all substances, which have been in contact with the device are
listed in section 5 and that the information is complete and that we have not withheld any information. We
declare that all measures - where applicable - have been taken listed in section ?Return to the factory?.
By our signature below, we acknowledge that we accept liability for any damage caused by providing incomplete or incorrect information and that we shall indemnify VACUUBRAND from any claims as regards
damages from third parties. We are aware that as expressed in ? 823 BGB (Public Law Code of Germany) we are directly liable for injuries or damages suffered by third parties, particularly VACUUBRAND
employees occupied with handling/repairing the product.
Shipping of the device must take place according to regulations.
Name: ....................................................................... Signature: ..............................................................
Job title: .................................................................... Company?s seal:
Date: .......................................................................
Release for repair grant by VACUUBRAND (date / signature):
VACUUBRAND GMBH + CO KG
Alfred-Zippe-Stra?e 4
97877 Wertheim, Germany
..............................................................
Tel.: +49 9342 808-5660
Fax: +49 9342 808-5666
E-Mail: service@vacuubrand.com
www.vacuubrand.com
page 105 of 106
EG-Konformit?tserkl?rung f?r Maschinen
EC Declaration of Conformity of the Machinery
D?claration CE de conformit? des machines
Hersteller / Manufacturer / Fabricant:
VACUUBRAND GMBH + CO KG · Alfred-Zippe-Str. 4 · 97877 Wertheim · Germany
Hiermit erkl?rt der Hersteller, dass die Maschine konform ist mit den Bestimmungen der Richtlinie 2006/42/EG. Hereby the manufacturer declares that the machinery is in conformity with the
directive 2006/42/EC.
Par la pr?sente, le fabricant d?clare, que la machine est conforme ? directive 2006/42/CE.
Membranvakuumpumpe / Diaphragm vacuum pump / Pompe ? membrane:
Typ / Type / Type: MD 4 NT VARIO / MV 2 NT VARIO / MV 10 VARIO-B
Artikelnummer / Order number / Num?ro d?article: 736300, 736301, 736302 / 738100, 738101,
738102 / 710500, 710501, 710502, 2614172
Seriennummer / Serial number / Num?ro de s?rie: Siehe Typenschild / See rating plate / Voir
plaque signal?tique
Die Maschine ist konform mit weiteren Richtlinien / The
?????????????????????????????????????????????
machinery is in conformity with other directives / La machine est conforme ? d?autres directives:
2006/95/EG, 2004/108/EG, 94/9/EG
Angewandte harmonisierte Normen / Harmonized standards applied / Normes harmonis?es
utilis?es:
DIN EN 12100:2004, DIN EN 61010-1:2010 (Ed. 3), DIN EN 1012-2:2011, DIN EN 1127-1:2011,
DIN EN 13463-1:2009,
DIN EN 61326-1:2006: 230V: Klasse / class / classe A + B
Bevollm?chtigter f?r die Zusammenstellung der technischen Unterlagen / Person authorized to
compile the technical file / Personne autoris?e ? constituer le dossier technique:
Dr. J. Dirscherl · VACUUBRAND GMBH + CO KG · Alfred-Zippe-Str. 4 · 97877 Wertheim · Germany
Wertheim,
24.02.2014
............................
Ort,
Datum / place, date / lieu, date
............................
(Dr. F. Gitmans)
Managing director / G?rant
.ppa.
................................
(Dr. J. Dirscherl)
Technical Director / Directeur technique
VACUUBRAND GMBH + CO KG
Alfred-Zippe-Str. 4 · 97877 Wertheim
T +49 9342 808-0 · F +49 9342 808-5555
info@vacuubrand.com
www.vacuubrand.com
page 106 of 106
Disclaimer: Our technical literature is only intended to inform our customer. The applicability of general empirical values and results obtained
under lab conditions to your specific operations depends on a number of
factors beyond our control. It is, therefore, strictly the users? responsibility to very carefully check the application of these data to their specific
requirements. No claims arising from the information provided in this literature will, consequently, be entertained.
Alfred-Zippe-Str. 4 · 97877 Wertheim / Germany
T +49 9342 808-0 · F +49 9342 808-5555
info@vacuubrand.com · www.vacuubrand.com
VACUUBRAND GMBH + CO KG
- Technology for Vacuum Systems © 2014 VACUUBRAND GMBH + CO KG Printed in Germany
Manual-no.: 999163 / 02/24/2014
Download