Cybex 750T Treadmill Owners Manual - Treadmill.co.uk

Cybex 750T Treadmill
Product Number 751T
Owner’s Manual
Cardiovascular Systems
Part Number LT-20406-4 H
www.cybexinternational.com
Cybex 750T Treadmill
Product Number 751T
Owner’s Manual
Cardiovascular Systems
Part Number LT-20406-4 H
CybexВ® and the Cybex logo are registered trademarks of Cybex International, Inc. Safety Sentryв„ў is a registered trademark of Cybex
International, Inc. PolarВ® is a registered trademark of Polar Electro Inc.
DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual. We reserve the
right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any
person of such revisions or changes.
В© 2010, Cybex International, Inc. All rights reserved. Printed in United States of America.
10 Trotter Drive Medway, MA 02053 • 888-462-9239 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • techhelp@cybexintl.com • LT-20406-4 H • March 2010
Cybex 750T Treadmill Owner’s Manual
Table of Contents
Front Pages
About this Manual . . . . . . . . . . . . . . . . . . iii
FCC Compliance Information. . . . . . . . . . iii
1 Safety
Important Voltage Information . . . . . . .
Grounding Instructions. . . . . . . . . . . . .
Important Safety Instructions . . . . . . . .
Warning Decals . . . . . . . . . . . . . . . . . .
Caution Decals . . . . . . . . . . . . . . . . . . .
Emergency Stop Key (e-stop) . . . . . . .
CSAFE Ports. . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-2
1-4
1-6
1-6
1-7
2 Assembly and Setup
Warnings/Cautions . . . . . . . . . . . . . . . . 2-1
Choosing and Preparing a Site . . . . . . 2-1
Electrical Power Requirements . . . . . . 2-2
Assembling the Treadmill . . . . . . . . . . . 2-2
Testing the Treadmill Operation . . . . . 2-10
Seup . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
3 Operation
Terms and Symbols Used . . . . . . . . . . 3-1
Quick Operation Guide. . . . . . . . . . . . . 3-2
Detailed Operation Guide. . . . . . . . . . . 3-2
Stopping the Treadmill . . . . . . . . . . . . . 3-5
Immobilization Method . . . . . . . . . . 3-5
Emergency Dismount . . . . . . . . . . . 3-5
Emergency Stop . . . . . . . . . . . . . . . 3-5
Safety Sentryв„ў. . . . . . . . . . . . . . . . . . . 3-5
Control During Operation . . . . . . . . . . . 3-6
Data Readouts . . . . . . . . . . . . . . . . . . . 3-6
Displaying Heart Rate. . . . . . . . . . . . . . 3-7
Heart Rate Zone . . . . . . . . . . . . . . . . . . 3-8
Meaning of % Grade . . . . . . . . . . . . . . 3-8
Preprogrammed Workouts . . . . . . . . . . 3-9
Custom Programs . . . . . . . . . . . . . . . . 3-9
Alarm . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Audio Visual (AV) Key Pad – Optional 3-11
Statistics . . . . . . . . . . . . . . . . . . . . . . . 3-12
4 Preventive Maintenance
Warnings/Cautions . . . . . . . . . . . . . . . .
Regular Maintenance Activities . . . . . .
Cleaning Your Treadmill . . . . . . . . . . . .
Running Belt Maintenance . . . . . . . . . .
Other Preventive Maintenance . . . . . . .
Service Schedule . . . . . . . . . . . . . . . . .
4-1
4-1
4-1
4-3
4-5
4-6
5 Customer Service
Contacting Service . . . . . . . . . . . . . . . .
Serial Number and Voltage . . . . . . . . .
Return Material Authorization (RMA) . .
Damaged Parts. . . . . . . . . . . . . . . . . . .
Ordering Parts . . . . . . . . . . . . . . . . . . .
5-1
5-1
5-2
5-2
5-3
Appendix A - Technical Specifications . . A-1
Appendix B - Program Overview . . . . . . . B-1
Appendix C - Parts List . . . . . . . . . . . . . . . C-1
Appendix D - Exploded Views. . . . . . . . . . D-1
Appendix E - Schematics . . . . . . . . . . . . . E-1
Page i
Cybex 750T Treadmill Owner’s Manual
Page ii
Cybex 750T Treadmill Owner’s Manual
About This Manual
An Owner’s Manual is shipped with each unit. To purchase additional copies of this manual or any other
Cybex manual, please do one of the following:
• fax your order to 508-533-5183
• contact Cybex Customer Service at 888-462-9239
• or contact Cybex Customer Service at 508-533-4300
To contact Cybex with comments about this manual you may send email to techhelp@cybexintl.com.
FCC Compliance Information
WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception (which
can be determined by turning the equipment off and on) the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio TV technician for help.
Page iii
Cybex 750T Treadmill Owner’s Manual
Page iv
Cybex 750T Treadmill Owner’s Manual
1 - Safety
IMPORTANT:
Read all instructions and warnings before using the treadmill.
Important Voltage Information
Before plugging the power cord into an electrical outlet, verify that the voltage requirements for the site
match the voltage of the treadmill that has been received. The power requirements for the Cybex 750T
Treadmill include a grounded, dedicated circuit, rated for one of the following:
•
•
•
•
•
100 VAC, 50/60 Hz, 20A
115 VAC, 60 Hz, 20A
220 VAC, 60 Hz, 15A
230 VAC, 50 Hz, 15A
230 VAC, 50 Hz, 13A, UK
See the serial number decal for the exact voltage requirements of the treadmill.
WARNING: Do not attempt to use this unit with a voltage adapter. Do not attempt to use this unit
with an extension cord.
WARNING: Do not plug more than one unit into a single circuit.
Grounding Instructions
This treadmill must be grounded. If it should malfunction or break down, grounding provides a path of
least resistance for electric current to reduce the risk of electric shock. This product is equipped with a
cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed and grounded in accordance with all local codes and
ordinances.
DANGER: Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service provider if there is doubt as
to whether the treadmill is properly grounded. Seek a qualified electrician to perform
any modifications to the cord or plug. Cybex is not responsible for injuries or damages
as a result of cord or plug modification.
This treadmill is for use on a
grounded, dedicated circuit. Make
sure that the treadmill is connected
to an outlet having the same
configuration as the plug. Do not
use a ground plug adapter to adapt
the power cord to a non-grounded
outlet.
115 VAC
NEMA 5-20
Euro Plug
CEE 7/7
220 VAC
NEMA 6-15
UK
230 VAC
Danish
IEC320
Safety
Page 1-1
Cybex 750T Treadmill Owner’s Manual
Important Safety Instructions
(Save These Instructions)
DANGER: To reduce the risk of electric shock, always unplug this treadmill from the electrical
outlet immediately after using it and before cleaning it.
WARNING: Serious injury could occur if these precautions are not observed. To reduce the risk
of burns, fires, electric shock, or injury:
User Safety Precautions
• Obtain a medical exam before beginning any exercise program.
WARNING: Heart rate monitoring systems may be inaccurate. Over exercise may result in serious
injury or death. If you feel faint stop exercising immediately.
• Stop exercising if you feel faint, dizzy, or experience pain and consult your physician.
• Obtain instruction before using.
• Read and understand the Owner’s Manual and all warnings posted on the unit before using.
• Read and understand emergency stop procedures.
• DO NOT wear loose or dangling clothing while using the treadmill.
• Keep all body parts, towels, water bottles and the like free and clear of moving parts.
• Place your feet on the two top steps when starting or stopping the treadmill.
• Use the treadmill handrails for support and to maintain balance.
• Keep children away from the treadmill. Teenagers and disabled persons must be supervised while
using.
• DO NOT use the unit if you exceed 400 lbs. (181 kg). This is the rated maximum user weight.
• Report any malfunctions, damage or repairs to the facility.
• Replace any warning labels if damaged, worn or illegible.
• Stop and place the treadmill at 0 degrees incline (level) after each use.
• Disconnect power before servicing.
Facility Safety Precautions
• Instruct all users on how to clip the e-stop clip onto their clothing and carefully test it prior to using the
treadmill.
• Instruct all users to use caution when mounting and dismounting the treadmill.
• Use a dedicated line when operating the treadmill. NOTE: A dedicated line requires one circuit breaker
per unit.
• Connect the treadmill to a properly grounded outlet only.
• DO NOT operate electrically powered treadmills in damp or wet locations.
Safety
Page 1-2
Cybex 750T Treadmill Owner’s Manual
• Keep the running belt clean and dry at all times.
• DO NOT leave the treadmill unattended when plugged in and running. NOTE: Before leaving the
treadmill unattended, always wait until the treadmill comes to a complete stop and is level. Then, turn
all controls to the STOP or OFF position and remove the plug from the outlet. Remove the e-stop key
from the treadmill.
• Immobilize the treadmill (when not in use) by removing the e-stop key.
• Inspect the treadmill for worn or loose components before each use. Do not use until worn or damaged
parts are replaced.
• Maintain and replace worn parts regularly. Refer to “Preventive Maintenance” section of Owner’s
Manual.
• DO NOT operate the treadmill if: (1) the cord is damaged; (2) the treadmill is not working properly or
(3) if the treadmill has been dropped or damaged. Seek service from a qualified technician.
• DO NOT place the cord near heated surfaces or sharp edges.
• DO NOT use the treadmill outdoors.
• DO NOT operate the treadmill around or where aerosol (spray) or where oxygen products are being
used.
• Read and understand the Owner’s Manual completely before using the treadmill.
• Ensure all users wear proper footwear on or around all Cybex equipment.
• Set up and operate the treadmill on a solid, level surface. Do not operate in recessed areas or on
plush carpet.
• Provide the following clearances: 19.7 inches (0.5 m) at each side, 79 inches (2.0 m) at the back and
enough room for safe access and passage at the front of the treadmill. Be sure your treadmill is clear
of walls, equipment and other hard surfaces.
• DO NOT attempt repairs, electrical or mechanical. Seek qualified repair personnel when servicing. If
you live in the USA, contact Cybex Customer Service at 888-462-9239. If you live outside the USA,
contact Cybex Customer Service at 508-533-4300.
• Use Cybex factory parts when replacing parts on the treadmill.
• DO NOT modify the treadmill in any way.
• DO NOT use attachments unless recommended for the treadmill by Cybex.
• Ensure all User and Facility Safety Precautions are observed.
Safety
Page 1-3
Cybex 750T Treadmill Owner’s Manual
• Carefully read and understand the following before using the 750T treadmill:
• Warning Decals
• Caution Decals
To replace any worn or damaged decals do one of the following: Visit www.cybexinternational.com
to shop for parts online, fax orders to 508-533-5183 or contact Cybex Customer Service at 888-462-9239.
If you are located outside of the USA, call 508-533-4300. For location or part number of labels, see the
parts list and exploded-view diagram. This information can be found in the Service chapter in this manual
or on the Cybex web site at www.cybexinternational.com.
Warning Decals
Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or
serious injury. The warning decals used on the Cybex 750T are shown below.
DE-20735-4
Warning
Safety
Page 1-4
Cybex 750T Treadmill Owner’s Manual
DE-20427
Warning Motor
Cover
Safety
Page 1-5
Cybex 750T Treadmill Owner’s Manual
Caution Decals
Caution decals indicate a potentially hazardous situation, which if not avoided, may result in minor or
moderate injury. There are no caution decals used on this unit. However, there are caution statements
listed in Chapters 2 and 5 of this manual. See Chapters 2 and 5.
Emergency Stop Key (e-stop)
The e-stop key functions as an emergency stop. In an emergency situation, the e-stop key disengages
from the console and the treadmill will come to a stop. Before using the treadmill, clip the e-stop key as
described below.
1. Compress the spring and clip the e-stop clamp to your clothing.
Ensure the clip engages enough clothing so it does not fall off in an
emergency situation. See Figure 1. NOTE: Be sure the string is free
of knots and has enough slack for you to workout comfortably with the
e-stop key in place.
Clothing
Clip
2. Without falling off the treadmill, carefully step backward until the
e-stop pulls out of the console. See Figure 2. NOTE: If the e-stop clip
falls off your clothing then the test has failed. Reclip the e-stop clip to
your clothing and repeat this step.
3. Replace the e-stop key. See Figure 2.
4. The treadmill is now ready to be used. NOTE: Ensure the the e-stop
clip is secured to your clothing at all times during use.
Figure 1
Figure 2
5. After use, remove the e-stop key from the treadmill.
NOTE: The e-stop key can be removed to help prevent unauthorized use. Refer to the Stopping the
Treadmill section in the Operation chapter for more information about the e-stop key.
Safety
Page 1-6
Cybex 750T Treadmill Owner’s Manual
NOTE: When not in use store the e-stop clip on the storage tab located on the lower cover. See Figure 3.
E-Stop
Lower
Cover
Storage
Tab
Clip
Figure 3
CSAFE Ports
The 750T Treadmill has two CSAFE ports, one in the console for CSAFE devices that need access
there, and one under the base of the unit for running a network connection.
NOTE: The CSAFE standard defines a communication protocol and low-voltage DC power source
specific to the Fitness Equipment Industry. These RJ-45 phone jacks are provided for use ONLY
within the CSAFE protocol. For more information on the CSAFE standard, visit
www.fitlinxx.com/csafe. Not every connection carries both the communication and power
capability.
NOTE: The console CSAFE port inside the console contains the full implementation, with both network
communications and a standard CSAFE voltage (minimum 8.0 VDC) power source. The base
CSAFE port is accessible under the base of the treadmill and is for network communications
only and does not contain the DC power source. See Figures 4 and 5.
Console CSAFE Port Location
CSAFE Port
(Lower Socket)
Figure 4
Safety
Page 1-7
Cybex 750T Treadmill Owner’s Manual
Base CSAFE Port Location
CSAFE
Port
Bottom View
Figure 5
Safety
Page 1-8
Cybex 750T Treadmill Owner’s Manual
2 - Assembly and Setup
Warnings/Cautions
All warnings and cautions listed in this chapter are as follows:
WARNING: Use extreme caution when assembling the treadmill. Failure to do so could result in
injury.
WARNING: During this procedure STAY OFF THE RUNNING BELT! Stand with your feet on the two
steps.
CAUTION: A minimum of two people are required to lift, move and assemble this treadmill.
Always use proper lifting methods when moving heavy items.
Choosing and Preparing a Site
Before assembling the treadmill a suitable site must selected and have the proper electrical outlet power
available for optimum operation and safety. See the Electrical Power Requirements section (located on
the next page) for direction in locating the treadmill’s voltage requirements.
The area selected for the treadmill should be well lit and well ventilated. Locate the treadmill on a
structurally sound and level surface (do not place in recessed areas or on plush carpet) a few feet away
from walls and other equipment. Each side of the treadmill should have a 19.7” (0.5 m) minimum space.
Behind the treadmill should be 79” (2.0 m) minimum of space. Allow enough clearance for safe access
and passage during use of the machine. If the treadmill is to be located above the first floor, place it near
or above major support beams. If the area has a heavy, plush carpet, the airflow around the base of the
machine may be restricted or the carpeting may interfere with the moving parts. To protect the carpeting
and the machinery, place a 3/4” (1.9 cm) thick wood base under the treadmill.
Do not install the treadmill in an area of high humidity, such as in the vicinity of a steam room, sauna,
indoor pool, or outdoors. Exposure to extensive water vapor, chlorine, and/or bromine could adversely
affect the electronics as well as other parts of the machine.
Assembly
and
Setup
Page 2-1
Cybex 750T Treadmill Owner’s Manual
Electrical Power Requirements
The power requirements for this treadmill are a grounded, dedicated circuit rated for one of the following:
•
•
•
•
•
100 VAC, 50/60 Hz, 20A
115 VAC, 60 Hz, 20A
220 VAC, 60 Hz, 15A
230 VAC, 50 Hz, 15A
230 VAC, 50 Hz, 13A, UK
Contact a qualified electrician to ensure the power supply complies with local building codes.
Do not use a ground plug adapter to adapt the 3-prong power cord plug to a non-grounded electrical
outlet. Do not use an extension cord.
Assembling the Treadmill
WARNING: Use extreme caution when assembling the treadmill. Failure to do so could result in
injury.
CAUTION: A minimum of two people are required to assemble this treadmill.
Tools Required
• 1/2” Socket wrench with a 4” extension
• 1/2” Box end wrench, 12 point
• 9/16” Socket wrench with a 4” extension
• Phillips screwdriver
NOTE: The words “left” and “right” denote the treadmill user’s orientation.
1. Read and understand all instructions thoroughly before assembling the treadmill.
NOTE: Each step number in the assembly instructions tells you what you will be doing. The lettered
steps following each step number describe the procedure required. Do not continue with step 2
until you have carefully read all of the assembly instructions.
2. Verify you have received the correct package.
A. Read the sticker on the outside of the box and verify that the model number, color and voltage are
what you ordered. NOTE: During step 3 and 5 you will verify that the contents of the box match
the sticker.
3. Unpack and verify the contents of the boxes.
A. Lift up and remove the cardboard sleeve that surrounds the treadmill.
B. Verify the following items are present. Check off ( пЂґ) each item as you find it. See Figure 1. If any
of the parts are missing contact Cybex Customer Service.
Assembly
and
Setup
Page 2-2
Cybex 750T Treadmill Owner’s Manual
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Part Number
Varies
Varies
AF-19921
AF-19922
AX-20383
PL-20264
PL-20262
PL-20263
PL-20355
PL-20211
PL-20356
PL-20357
PL-20210
AX-20454
LT-20406-4
LT-20404
LT-20405
AX-20552
Description
Base assembly
Console assembly
Upright, Left
Upright, Right
Motor cover, Top
Motor cover, Front
Motor cover, Left (in box)
Motor cover, Right (in box)
Upright cover, Outer, Left (in box)
Upright cover, Inner, Left (in box)
Upright cover, Inner, Right (in box)
Upright cover, Outer, Right (in box)
Console cover, Back
Hardware pack (in box)
Owner’s Manual (in box)
Assembly poster
Warranty sheet
Assembly, E-stop lanyard
#14
#15
#16
#17
#13
#2
#8
#7
#11
#10
#12
#5
#18
#6
#9
#3
#4
#1
Figure 1
Assembly
and
Setup
Page 2-3
Cybex 750T Treadmill Owner’s Manual
C. Check off (пЂґ) each item in the hardware pack as you find it. See Figure 2.
Item
19
20
21
22
23
24
25
Qty
9
10
9
2
2
4
2
Part Number
HS-16939
HS-16929
HS-15706
HS-41050
HS-20361
HN-42063
HW-00189
Description
Screw, SEMS, 10-32 x .75”, PNHD, BLK
Bolt, Whiz Lock, 3/8-16 x .625”, HXHD
Screw, 8/16 x .50”, PNHD, STL, BLK
Bolt, 5/16-18 x 2.25”, HXHD
Screw, SLFTP, 8/16 x 2.5”, Plastite, BLK ZN
Nut, 5/16-18, Flanged, SS
Washer, Flat 5/16”
Hardware
#20
#19
#21
#22
#23
#24
#2
#13
#11
#21
#24
#22
#24
#22
#9
#5
#23
#3
#25
#12
#25
#10
#4
#19
#20
#8
#19
#20
#6
#19
#7
#1
Assembly
and
Figure 2
Setup
Page 2-4
#25
Cybex 750T Treadmill Owner’s Manual
CAUTION: A minimum of two people are required to lift, move and assemble this treadmill.
Always use proper lifting methods when moving heavy items.
4. Lift and move the treadmill.
A. At least two people should lift and move the treadmill to a level location where you intend to leave
it. Use proper lifting methods.
5. Verify the model and voltage.
A. Verify that you have the correct model and voltage by looking at the serial number label located
at the rear of the unit.
6. Install the uprights.
A. Locate the left upright (#3) and five bolts, 3/8-16 x .625” (#20).
B. Carefully place the left upright (#3) on the base assembly (#1) as shown. See Figure 3.
C. Using a 9/16” Socket wrench,
partially tighten each of the five
bolts, 3/8-16 x .625” (#20). See
Figure 3.
#3
#20
D. Repeat steps 6A to 6C for the
right upright (#4).
7. Install the console assembly to
the uprights.
A. Locate the console assembly
(#2), bolt 5/16-18 x 2.25” HXHD
(#22), washer (#25) and two
nuts (#24). See Figure 4.
NOTE: Do not pinch or damage display
cable when installing console
assembly.
#20
#1
#20
B. Place the console assembly
Figure 3
(#2) in position on the left upright
(#3). See Figure 4.
C. Using a 1/2” box end wrench, partially
tighten the bolt 5/16-18 x 2.25”,
HXHD (#22), washer (#25) and two
nuts (#24). See Figure 4.
#2
#22
#24
#25
#3
Figure 4
Assembly
and
Setup
Page 2-5
Cybex 750T Treadmill Owner’s Manual
D. Repeat steps 7A to 7C for the right upright.
E. Using a 1/2” box end wrench, fully tighten the two bolts, 5/16-18 x 2.25”, HXHD (#22) and four
nuts (#24) securing the console assembly to the uprights. See Figure 4.
F. Using a 9/16” Socket wrench, fully tighten the ten bolts, 3/8-16 x .625” (#20) securing the uprights
to the base assembly (#1). See Figure 3.
8. Install the Display Cable.
NOTE: Do not pinch or damage display cable
when installing.
A. Locate the display cable exiting the
back of the console assembly.
B. Insert the display cable into the top of
the left upright (#3) until it exits at the
base of the upright (#3). See Figures
5 and 6.
C. Plug the display cable, located at the
bottom of the upright assembly (#3)
into the hub board connector J3. See
Figure 6.
NOTE: If installing the A/V option, refer to
the 750T A/V bracket installation
instructions (supplied with the A/V
bracket).
#3
Display
Cable
Figure 5
Hub Board
Connector J3
Figure 6
Assembly
and
Setup
Page 2-6
#3
Display
Cable
Cybex 750T Treadmill Owner’s Manual
9. Attach the upright covers (four pieces).
A. Locate the outer left upright cover
(#9), inner left upright cover (#10)
and one screw 8/16 x 2.5” (#23).
See Figure 7.
B. Place the two upright covers in
place over the left upright (#3). See
Figure 7.
C. Insert the screw 8/16 x 2.5” (#23)
into the inner left upright cover
(#10) and secure using a Phillips
screwdriver. See Figure 7.
#23
D. Repeat steps 9A to 9C for the right
side.
10. Attach the back console cover.
A. Locate the back console cover (#13)
and nine screws 8/16 x .50” (#21).
See Figure 8.
#9
#10
#3
Figure 7
#2
#13
B. While being sure not to pinch any
cables, use a Philips screwdriver to
secure the nine screws 8/16 x .50”
(#21) that hold the back console cover
(#13) to the console assembly (#2).
See Figure 8.
#21 (9)
Figure 8
Assembly
and
Setup
Page 2-7
Cybex 750T Treadmill Owner’s Manual
11. Attach the motor covers (four pieces).
A. Locate the front motor cover (#6) and five
screws 10-32 x .75” (#19). See Figure 9.
#6
NOTE: Elevate or tip the treadmill on it’s side to install
the two lower screws (#19).
B. Using a Phillips screwdriver partially tighten
the front motor cover (#6) to the base (#1)
with five screws 10-32 x .75” (#19). See
Figure 9.
C. Locate the left motor cover (#7) and four
screws 10-32 x .75” (#19)
D. Using a Phillips screwdriver, partially tighten
the left motor cover (#7) with two screws
10-32 x .75” (#19). See Figure 10.
E. Repeat steps 11C and 11D for the right
side.
F.
#19
#1
Figure 9
#19
Locate the motor cover top (#5).
G. Place the motor cover top (#5) into
position by aligning the four tabs over the
front and side cover screws. See
Figure 11.
#8
NOTE: If motor cover top does not fit properly,
loosen the front and side cover screws as
needed.
H. Using a Phillips screwdriver, finish
tightening the five front cover screws and
four side cover screws. Be sure the screws
are securing the motor cover’s tabs. See
Figure 11.
#7
Figure 10
#5
12. Level the treadmill.
A. Confirm that the treadmill is on a level
surface.
Tabs
Figure 11
Assembly
and
Setup
Page 2-8
#19
Cybex 750T Treadmill Owner’s Manual
13. Attach emergency stop key.
A. Confirm that the emergency stop key is in place in the bottom of the console handrail. See
Figure 12. NOTE: The treadmill will not run without the key in place.
Console
Handrail
Emergency
Stop Key
Figure 12
14. Visually inspect the treadmill.
A. Carefully examine the treadmill to ensure that the assembly is correct and complete.
Assembly
and
Setup
Page 2-9
Cybex 750T Treadmill Owner’s Manual
WARNING: Be sure that all electrical requirements are met as indicated in the specifications at
the front of the manual and at the beginning of this chapter prior to proceeding.
Testing the Treadmill Operation
Use the following instructions to test the full speed and incline range of the treadmill and to check the belt
for proper operation.
CAUTION: During this procedure STAY OFF THE RUNNING BELT! Stand with your feet on the two
steps.
NOTE: Cybex recommends that the treadmill be unplugged or the on/off (I/O) power switch turned off (O)
when it is not in use.
1. Without anyone on the treadmill, plug the power cord into a power outlet from a grounded, dedicated
circuit as described under Electrical Requirements in this chapter.
NOTE: Ensure the power cord is not being pinched under the front of the treadmill.
2. Locate the on/off (I/O) power switch in the front motor cover of the treadmill. Toggle it to the on
position (I).
3. The control panel will light up and be in the Dormant Mode.
4. Press the Quick Start key. The treadmill begins a countdown “BELT START IN 3...2...1” and sounds
a tone for each count. After it reaches one (1), the treadmill gives a longer tone and then begins
accelerating the belt to reach 0.5 mph (0.8 kph).
5. The lower left display will show the incline then time and the lower right display will show the actual
speed.
6. Press and hold down the Speed + key until the treadmill reaches a speed of approximately 4 mph
(6.4 kph), as indicated on the display.
7. Observe the belt to see that it is running properly; it should stay centered in the middle of the deck. If
you have problems with the running belt operation, see Running Belt Adjustments in the Preventive
Maintenance chapter.
8. Run the treadmill through its full speed range. First press the Speed + key until the treadmill reaches
its highest speed. Then press the Speed - key until the treadmill is back to 0.5 mph (0.8 kph).
9. As you press the Incline
or speed.
or Speed + - keys, the respective displays will show the actual incline
10. When the treadmill reaches the set incline and speed, the displays will remain steadily illuminated to
indicate that the desired settings have been reached.
11. Run the treadmill through its full % grade range. Press the Incline
key until the treadmill reaches
its highest grade (15%). Then press the Incline
key until the treadmill reaches -3% grade.
12. Press the Stop key to stop the running belt, end the workout review and return the display to
Dormant Mode.
Assembly
and
Setup
Page 2-10
Cybex 750T Treadmill Owner’s Manual
Setup
1. While in Dormant Mode enter Set Up Mode by pressing the following buttons on the keypad
Clear 750 and then press the Enter key. You will now be in the set up menu.
2. Press the Speed + and - keys to scroll through the set up options. Press the Enter key to edit options,
change values with the Incline
and
keys or the Speed + and - keys. Press Enter to save your
selection and return to the set up menu. Press the STOP key to exit to Dormant Mode. Press the
CLEAR key to reset to the previous stored value, and exit back to the menu. The set up options are
displayed in the following order:
Language (Language):
This selects the language displayed in the text area of the console. Language choices are:
•
•
•
•
•
•
•
•
ENGLISH (Default)
GERMAN
FRENCH
SPANISH
JAPANESE
SWEDISH
RUSSIAN
DANISH
Units (UNITS):
Choices are “ENGLISH (LB/MPH)” or “METRIC (KG/KPH)” measurements. English is the default.
Frequency (FREQUENCY):
This is the frequency of the power line that supplies power to your treadmill. The default setting is 60 Hz.
NOTE: If you have an English console and a 50 Hz power line frequency, then you must change the default
setting from 60 Hz to 50 Hz for the proper elevation frequency.
Clock Style (HH:MM / MM:DD:YY or DD:MM:YY):
The 750T features a clock and calendar. The clock can be displayed in a 12 or 24 hour format. The
calendar date fomat can be displayed as Month-Day–Year (US) or Day–Month–Year (EU).
“12HR
“24HR
“12HR
“24HR
US DATE”
EURO DATE”
EURO DATE”
US DATE”
Current Time (HH:MM):
The 750T features a clock that displays the current time. Examples for 2:57 PM on May 10, 2007.
12HR
24HR
12HR
24HR
US DATE
EURO DATE
EURO DATE
US DATE
“02:57P 5/10/2007”
“14:57 10-05-2007”
“02:57P 10-05-2007”
“14:57 5/10/2007”
Assembly
and
Setup
Page 2-11
Cybex 750T Treadmill Owner’s Manual
Default Time (DEFAULT TIME):
This is the default time for time based programs if a user does not re-set Time. For example, if you press
Time you can decrease or increase the set workout time up to the amount that the Max time is set.
Choices are 10, 20, 30, 60 and 90 minutes. Default is 30 minutes.
Review Time (REVIEW TIME):
This is the Review Time for which the user’s workout results are displayed at the end of a workout.
Choices are 0:10, 0:20, 0:30, 1:00 and 5:00 minutes. Default is 20 seconds.
Max Time/Time Zones (MAX TIME = MINUTES, ZONED OR OFF):
This is the maximum amount of time the treadmill can run per user workout session. You can limit the
users time or choose �OFF’ to disable the Max Time. Valid choices for Max Time are OFF, 20, 30, 40, 50,
60, 90 and 120 minutes or ZONED. For ZONED, you can define a user maximum session time based on
four time zones. This allows limiting use only during busy times of the day.
This is how ZONED is configured from the factory:
ZONE1 5:01A 60
ZONE2 9:01A OFF
ZONE3 4:01P 60
ZONE4 9:00P OFF
The maximum session time is limited to 60 minutes from 5AM - 9AM and from 4PM to 9PM in this
example, with all other times unlimited. The zone start/stop time and the time limit in each zone can be
modified to suit your needs.
Pause Time (PAUSE TIME):
This is how long the treadmill retains and displays your current workout data during a pause in the
workout. Choices include: Off; 1 minute; 5 minutes; and 10 minutes; default is Off.
WARNING: It is strongly suggested to not allow any user on the treadmill without adequate
instruction. The use of a treadmill at high speeds can be dangerous and potentially
result in injury. To avoid injury no user should be allowed to use the treadmill at a
speed that exceeds their level of ability.
The 750T Treadmill has been programmed to have a default maximum speed of 12.4
mph from the factory. As the owner of this treadmill you may change the default
setting for maximum speed up to 15 mph. Please be aware that higher speeds have
higher risk and if a user exceeds their ability, they can potentially loose coordination
that can result in injury.
The e-stop clip should be worn at all times.
Max Speed (MAX SPEED):
This is the maximum speed the treadmill will run. Choices are between .5 and 15.6 MPH (0.8 to
25.1 kph). Default MAX SPEED is set at 12.4 MPH (20.0 KPH).
Max Incline (MAX INCLINE):
This is the maximum elevation the treadmill will incline. Choices are between 0 and 15 percent grade.
NOTE: Setting both the Min and Max incline to 0 percent will disable the elevation.
Min Speed (MIN SPEED):
This is the minimum speed the treadmill will run. Choices are between .5 and 1.0 MPH (0.8 to 1.6 KPH).
Min Incline (MIN INCLINE):
This is the minimum elevation the treadmill will decline. Choices are between -3 and 0 percent grade.
NOTE: Setting both the Min and Max incline to 0 percent will disable the elevation.
Assembly
and
Setup
Page 2-12
Cybex 750T Treadmill Owner’s Manual
Sound (TONE - ON/OFF):
This option will enable or disable the beeper by toggling it on/off. Default is On.
Dormant Display Option (DORMANT STYLE):
This defines what is displayed in Dormant mode. Valid Choices for Dormant Display are:
0 – DEFAULT 1 – TEXT MSG - Not Applicable.
2 – OUT OF ORDER - Out of Order message.
3 – CLOCK - Time clock.
4 – PROFILES - Displays program profiles.
Lock Combination (LOCK CODE).
This feature will allow the Lock Combination (PIN) to be changed. It requires the correct PIN number to
be entered first before allowing any changes.
The PIN numbers will be entered using the keypad. If an incorrect PIN number is entered, the number will
blink once and revert back to underscores. If a valid PIN number is entered, blink the ON or OFF (default)
text (whichever was previously stored) and allow the Speed Control Key to toggle it.
Custom Programs - (SAVE PROGRAM).
The ability to SAVE a workout session as a custom program during Review is enabled or disabled here.
If disabled, the SAVE button will not be active during Review. The text area will display Save Program
On or Save Program OFF (default).
Remember: You must press Enter after changing a value for that value to be stored.
3. To exit Set Up Mode press the Stop key once.
Your treadmill is now ready for use. Follow the instructions in the Operation chapter to learn how to operate
the treadmill. You should begin with walking speeds first, to be sure everything is functioning properly.
Assembly
and
Setup
Page 2-13
Cybex 750T Treadmill Owner’s Manual
This page intentionally left blank.
Assembly
and
Setup
Page 2-14
Cybex 750T Treadmill Owner’s Manual
3 - Operation
Read and understand all instructions and warnings prior to using the treadmill. See all of the safety
related information located in chapter 1.
Terms and Symbols Used
This section lists some of the common terms and symbols used in this chapter. Other terms and symbols
are listed in this chapter as appropriate. NOTE: For setup options see Setup in Chapter 2.
Dormant Mode — This occurs when the treadmill is powered up and not in use. NOTE: Dormant Mode
may display a clock, scrolling text or the Cybex logo if such options are chosen.
Wake-up Mode — This occurs when motion is detected or a key is pressed. A tone will be heard.
Program Setup Mode — This begins after pressing the Programs key, Fit Tests key, Enter key or the
number key corresponding to the program desired.
Active Mode — Active Mode is when the running belt is moving. Before Active Mode begins, a three
second countdown and “BELT START IN 3...2...1” is displayed. Active Mode continues until the preset
time limit is reached, disengage the e-stop key, press the STOP key or press the Pause/End key.
Quick Start — This begins by pressing the Quick Start key. Quick Start skips the Program Setup Mode
and begins immediately in Quick Start Manual Mode with time counting up.
Manual Mode — In this active mode the user controls all aspects of the workout; the running speed, the
incline and the workout duration. The time will count down, allowing the user to quickly get moving before
entering their weight by pressing the Weight key.
Workout Review — This begins after pressing the Stop key once or at the end of a program or when
the treadmill detects that the user is not there (see Safety Sentryв„ў in this chapter). The workout statistics
accumulated during the previous workout session will display for the preset review time.
Pause Mode — Press the Pause/End key once. If Pause is enabled in Setup, the Pause feature will
allow the treadmill to hold the accumulated workout data for up to five minutes. The time remaining will
be displayed on the screen. Press START at any time to re-start the treadmill. If Pause is not enabled,
this key acts like the STOP key and will end the workout session.
Cool Down — This begins immediately after pressing the Cool Down key. The countdown timer is set
to two minutes, elevation returns to 0% and speed is reduced to 50% of the MET level or 2.5 MPH (4
Km/H) whichever is lower. Repeated presses of the Cool Down key will restart the clock at two minutes
indefinitely.
The last two minutes of a Programs (P1 – P9) will reduce the incline to 0% and the speed to half of the
MET level for each of the two remaining minutes. Cool down will also be active when Manual or Quick
Start workouts end due to the set or max time.
— These keys adjust Incline higher or lower.
+– —
These keys adjust Speed up (+) or down (–).
Operation
Page 3-1
Cybex 750T Treadmill Owner’s Manual
Quick Operation Guide
NOTE: Maximum user weight is 400 lbs. (181 kg).
The following is a quick overview of the operation of the treadmill. For more information read Detailed
Operation Guide in this chapter.
1. Place your feet on the two top steps located on each side of the running belt.
WARNING: Do not stand on the running belt when starting the treadmill. Always place your feet
on the two top steps when beginning a workout.
2. Clip the e-stop clip onto your clothing and test it as described under Emergency Stop in the Safety
chapter.
3. Press the Programs, Manual or Fit Tests keys and follow the on-screen setup instructions or press
QUICK START to start the treadmill in Quick Start Manual mode.
4. If a program is selected, you will be prompted for workout Time, Level and Weight as appropriate.
Adjust these settings with the Speed + – keys and press Enter to proceed.
5. The treadmill begins a countdown, “BELT START IN 3...2...1,” after which it accelerates the belt to
0.5 mph (0.8 kph) (for Manual Mode) or the speed of the program selected.
6. Hold the handrails while you step onto the running belt and begin walking.
7. Press the Speed + – keys to change the belt speed at any time. The right display will show the
current speed.
8. Press the Incline
keys to change the incline at any time. The left display will show incline.
9. Press the Stop key at any time to stop the running belt. Press again to exit to Dormant Mode and
return the incline to 0%.
Detailed Operation Guide
NOTE: Maximum user weight is 400 lbs. (181 kg).
1. Plug the treadmill power cord into a power outlet from a grounded, single phase, dedicated circuit, rated
for one of the following:
100 VAC, 50/60 Hz, 20A
115 VAC, 60 Hz, 20A
220 VAC, 60 Hz, 15A
230 VAC, 50 Hz, 15A
230 VAC, 50 Hz, 13A, UK.
2. Set the on/off switch to the on position.
WARNING: Do not stand on the running belt when starting the treadmill. Always place your feet
on the two top steps when beginning a workout.
3. Place your feet on the two top steps located on each side of the running belt.
Operation
Page 3-2
Cybex 750T Treadmill Owner’s Manual
4. Clip the e-stop clip onto your clothing and carefully test the e-stop key to ensure it will activate in case
of an emergency. See Emergency Stop Key (e-stop) in Chapter 1 for properly testing the e-stop key.
Also, see Stopping the Treadmill in this chapter for further information about the e-stop key. NOTE:
Be sure the string is free of knots and has enough slack for you to run comfortably with the e-stop key
in place.
5. You now have the option to select a program, a fitness test or enter Manual Mode.
To select a program, press the Programs or Fit Tests key and follow the prompts. Press the
Programs or Fit Tests key multiple times to cycle through its nine programs, or use the numeric
keypad to select the program number. Press Enter to select. See Figure 1.
Heart Rate
Indicator
Bar Graph
Text Area
Data
Readouts
QUICK
START
Programs
Key Pad
Time / Incline
Speed / PrX
Figure 1
Upon entering a program the display will guide you through the appropriate settings. This is referred
to as Program Setup Mode. If the Quick Start key is pressed now, all defaults for that program will be
accepted. After 10 seconds, if no key has been pressed, the first default will be accepted. After another
10 seconds the second default will be accepted and so on until the last default. The program will not
enter Active Mode until you press the Enter or Quick Start key. If no key has been pressed for 60
seconds after displaying the last default, then the treadmill will return to the Dormant Mode.
If you choose to enter Manual Mode instead of choosing a program, press the Quick Start or the
Manual key. NOTE: No prompts will occur when you press Quick Start. While in Manual Mode,
customize your workout Speed, Incline and enter your Weight by pressing those keys.
NOTE: For the most accurate calorie count, you must set your correct weight before beginning your
workout (including clothing).
NOTE: When selecting a program you must press Enter after each adjustment of Time, Level and
Weight.
Operation
Page 3-3
Cybex 750T Treadmill Owner’s Manual
6. The treadmill begins a countdown, “BELT START IN 3...2...1,” and sounds a tone for each count.
When it reaches one (1) the treadmill gives a longer tone and then starts accelerating the belt. In
Manual Mode the belt will begin accelerating to 0.5 mph (0.8 kph) and the incline will remain at zero
percent. In a program the belt will begin accelerating and the incline will change to the corresponding
speed and incline of the program and level you selected.
7. Hold the handrails while you step onto the running belt and begin walking.
8. Observe the control panel. The top center Bar Graph display shows a graphical representation of
the relative incline changes, and if in a program, will show the relative intensity changes that are
coming up. The Text Area will start showing the workout data such as Distance, Calories, Heart
rate (if available), METs and Pace (Minutes per Mile or Minutes per Km). The data displays will start
by automatically shifting every five seconds. To hold on one display, press the Shift/Scan key. To
continue auto-scan, hold the Shift/Scan key for 3 seconds until it beeps.
NOTE: Heart rate will be displayed in lieu of METs if a valid heart rate is available from a wireless chest
strap (not included) or by holding the contact heart rate grips.
NOTE: When you adjust incline in a program, the change will affect only the current segment. The
program control will resume starting with the next segment. To increase or decrease overall
intensity, adjust the speed and/or the program level.
9. Press the Speed + – keys to change the belt speed at any time. The right display will show the set
speed.
10. Press the Incline
keys to change the incline at any time. The left display will show the current
incline only when incline keys are used, then revert to time.
11. Press the Stop key at any time to stop the workout. Press Stop once to end the workout and begin
the Workout Review. As you press Stop once, the treadmill belt will stop. Press Stop a second time to
clear the Workout Review, return to Dormant Mode and return incline to 0%.
12. If the e-stop key is removed during a workout, the drive motor power shuts off immediately, causing
the belt to stop. “EMERGENGY STOP” is displayed, followed by “REPLACE E-STOP KEY TO
CONTINUE”. Replacement of the e-stop key causes Workout Review to begin.
13. When a program is complete the treadmill begins a countdown, “BELT STOP IN 3...2...1,” and sounds
a tone for each count. The belt slows to a stop and Workout Review is displayed for the preset time or
until you press the Stop key.
14. The treadmill returns to Dormant Mode and the incline returns to 0%.
Operation
Page 3-4
Cybex 750T Treadmill Owner’s Manual
Stopping the Treadmill
Press Stop once to end the workout session and start the Workout
Review. The treadmill will perform a controlled belt stop and bring
the incline to 0%. The Text Area will be displaying accumulated
data or the results of the Fitness Test for the duration configured in
Setup for Review Time (default is 20 seconds.) Press Stop again
to exit to Dormant.
The function of the immobilization method: The purpose of
immobilizing the treadmill is to prevent unauthorized use. This can
be accomplished by removing the e-stop key from the treadmill,
un-clipping it from the cord and putting it in a non-accessible place.
See Figure 2. NOTE: Immobilization can also be enabled
using the LOCK code. Either temporarily by pressing
LOCK during review and entering the correct PIN number,
or permanently by enabling the LOCK feature in SETUP
mode. See Setup in Chapter 2.
Figure 2
The emergency dismount: Follow the steps listed below
if you experience pain, feel faint or need to stop your
treadmill in an emergency situation:
1. Grip handrails for support.
Figure 3
2. Step onto the top steps.
3. Pull the e-stop key off the console.
The function of the emergency stop: The e-stop key functions as the emergency stop. In an
emergency situation, remove the e-stop key from the treadmill and the running belt will come to a stop.
See Figure 3.
Safety Sentry
If you step off of your treadmill during a workout, it is designed to detect your absence and will stop the
belt. Before taking action, the display will beep several times and display “ARE YOU THERE?” on the text
area. If no response in 10 seconds, it will proceed to turn off the belt.
NOTE: The treadmill will use every sensor available to determine a user is still on the belt before asking
if you are present, then shutting it off. If the user is lighter than 100 lbs. (45 Kg), the motor drive
may not be able to determine they are on the belt. In this instance, the treadmill can only rely
on the motion sensor, key inputs, or the heart rate to establish your presence. It is advisable
for lighter users to stay within the �sight’ of the motion sensor (no further back than the end of
the handrails) or take advantage of the wireless heart rate feature to avoid triggering the Safety
Sentry.
Operation
Page 3-5
Cybex 750T Treadmill Owner’s Manual
Control During Operation
Control keys are usable during operation and may be pressed at any time to make adjustments in speed,
elevation or data readouts. The Speed and Incline keys are located near the hand grips, allowing for
thumb adjustments without removing your hands from the hand grips.
Changing Speed — Press the Speed + – keys to change the speed in increments of 0.1 mph or 0.10
kph. Minimum to maximum speed is from 0.5 - 15.6 mph (0.8 - 25.1 kph). Default max speed is 12.4 mph
(20.0 kph).
Direct Speed Access — During programs, manual mode and all distance based fitness tests a direct
speed value may be entered. Press the “0” key on the numeric keypad and then enter the desired speed
including tenths. Example: For 5 MPH (8.0 KPH) press the “0” key, then press 5-0 (8-0) on the keypad
then press ENTER.
Changing Incline — Press the Incline
keys to change the elevation in increments of 1%.
Elevation ranges from -3 to 15%. Press multiple times to change incline setting. NOTE: Elevation is
defined as the ratio of rise or fall over run of the treadmill deck.
Workout Time — When the treadmill is in Active Mode, the workout time can be set to a new time using the
TIME key. This will convert a Quick Start session to a Manual Session by defining the count-down time, or
change the total session time in a program. All treadmill usage is limited to the MAX TIME as configured in
Setup.
Changing Data Readouts — Default setting is for Scan to start automatically. Press Shift/Scan to stop
and display a set of data. Press and hold Shift/Scan for three seconds and it will continually review each
set of data. The display shows each set of data for 5 seconds before switching to the next set.
Data Readouts
As you exercise, the treadmill keeps track of the following data:
Distance — The total accumulated distance, in miles or kilometers, during your workout. NOTE:
Depending on the defaults you’ve chosen this measurement will show in English or Metric.
Calories — The total accumulated calories burned during your workout. Your weight must be correctly
set before beginning your workout for this measurement to be most accurate.
Calories Per Hour — Calculation of present workload’s energy exertion in Calories per Hour.
BPM (Beats Per Minute) — Your current heart rate. Heart rate will appear when a signal is introduced.
Use the hand grips for Contact Heart rate or wear a PolarВ® compatible heart rate chest strap.
Time — The total time you’ve been working out or time remaining. Display time as hours:minutes.
Pace — At your current speed, how long it would take to cover a mile (or kilometer), displayed in
minutes:seconds.
Metabolic Equivalent (METs) — Relates to the user’s energy expenditure. A MET is a basic unit of
measurement that is used to compare relative work between individuals and activities. �One MET’ is the
amount of oxygen consumed at rest. For example, two METs would be twice that amount. If an individual
were working at four METs he/she would be consuming oxygen at a rate equal to four times their resting
consumption. METs can be used to compare walking on a grade with running or even to cycling and
other activities.
Operation
Page 3-6
Cybex 750T Treadmill Owner’s Manual
To review accumulated data after a program: The display automatically shows the accumulated
workout data during the Workout Review for the set review time. See Setup in Chapter 2.
Displaying Heart Rate
In order for the Cybex 750T to display your heart rate, hold the hand grips to use Contact Heart rate or
wear a PolarВ® compatible heart rate chest strap.
Contact Heart Rate — Hold the hand grips on the console handrail until a heart rate is displayed,
typically less than thirty seconds. For best results, hold the hand grips lightly and ensure that your hands
contact both the front and back sensors of each grip. NOTE: Hold your hands as steady as possible as
movement can cause interference on the contacts.
Factors that can interfere with the heart rate signal include:
•
•
•
•
•
•
•
•
excessive movement
body composition
hydration
too loose grip
too tight grip
running
excessive dirt, powder or oil
leaning or resting on grips
NOTE: Cybex does not recommend continuous holding onto the contact heart rate grips during
exercise.
Contaminants, such as hand lotions, oils or body powder, may come off on the contact heart rate grips.
These can reduce sensitivity and interfere with the heart rate signal. It is recommended that the user
have clean hands when using the contact heart rate.
Operation
Page 3-7
Cybex 750T Treadmill Owner’s Manual
Heart Rate Zone
Heart rate is described by the number of times your heart beats in a minute. At rest, the average adult will
have a heart rate of about 72 beats per minute (BPM). As one begins to exercise, heart rate increases
and continues to increase as exercise intensity or difficulty increases.
Monitoring your heart rate is an effective way to control
the intensity of your workout and subsequently the
results it will have. Whether you are a new participant
or one with a great deal of experience, weight loss and
other performance goals can be achieved by controlling
the intensity of your workout.
The American College of Sports Medicine recommends
that healthy adults exercise between 55 and 85%
of their heart rate max. Your heart rate max can be
estimated by subtracting your age from 220. Multiply
that estimated heart rate max by .55 to estimate
the lower end of your heart rate training zone. Then
multiply your estimated heart rate max by .85 to
estimate the higher end of your training zone. This
heart rate training zone gives you a range of intensities
at which to exercise. See Figure 4.
This chart shows heart rate based on
percentage and age.
Heart Rate Zone
Beats
Per
Minute
Ma
x
200
85
%
180
65
%
160
140
120
100
80
60
Meaning of % Grade
A 1% grade is not the same as a 1 degree incline.
The % grade is the relationship of the measurement
of rise over the measurement of run (also called slope).
For example, a 1 foot (meter) rise in height over a length
of 100 feet (meters) is a 1% grade. Expressed as a
mathematical formula, the grade is calculated as follows:
1 ft. (m) / 100 ft. (m) = 0.01 = 1%
Age 20
30
40
50
60
70
220 - Age = Max Heart Rate
Figure 4
With respect to treadmills, the percent grade is roughly equal to the increase in height (rise) of the
treadmill divided by the length (run) of the treadmill.
The degree of incline can be related to % grade by taking the Arctangent of the grade. For instance, 15%
grade is equal to 8.53 Degrees (ArcTan(.15)=8.53Вє). The opposite is true to determine % Grade from
Degree of incline (Tan (8.53Вє)=.15).
Operation
Page 3-8
Cybex 750T Treadmill Owner’s Manual
Preprogrammed Workouts
WARNING: Obtain a medical exam before beginning any exercise program. Begin comfortably
with a lower level and progress with higher levels as you become acclimated.
With the 750T, you may choose from Quick Start Manual Mode, nine program choices, eight fitness tests,
and nine custom programs. Each routine will be described in detail in this chapter.
Manual Choices:
Quick Start
Press Quick Start. You control speed, elevation.
Manual Mode Enter time and weight. You control speed, elevation.
Program
No.
P-1
P-2
P-3
P-4
P-5
P-6
P-7
P-8
P-9
Choices:
Name
Weight Loss
Rolling Hills
Hills
Pikes Peak
Hill Interval 1:1
Hill Interval 1:2
Hill Interval 1:3
Cardio
HR Control
Fitness Test Choices:
No. Name
FT1
FT2
FT3
FT4
Gerkin Protocol
Army PFT
Air Force PFT
Navy PRT
FT5 Navy PRT
FT6 Marines PRT
FT7 Marines PRT
FT8 One Mile
Levels
10 levels.
10 levels
10 levels.
10 levels.
10 levels.
10 levels.
10 levels.
10 levels.
N/A
Data Entries/Selections
Select time, level and weight.
Select time, level and weight.
Select time, level and weight.
Select time, level and weight.
Select time, level and weight.
Select time, level and weight.
Select time, level and weight.
Select time, level and weight.
Select time, age, target heart rate and weight.
Type
Data Entry
Results
Walk/run
2 mile/3.2 k run
1.5 mile/2.4 k run
1.5 mile/2.4 k run
under 5000 feet
1.5 mile/2.4 k run
over 5000 feet
3 mile/4.8 k run
sea level
3 mile/4.8 k run
4500 feet
1 mile/1.6 k walk
Age,
Age,
Age,
Age,
VO2 max.
Points.
Points.
Points.
weight and gender.
weight, gender and starting speed.
weight, gender and starting speed.
weight, gender and starting speed.
Age, weight, gender and starting speed.
Points.
Age, weight, gender and starting speed.
Points.
Age, weight, gender and starting speed.
Points.
Age, weight, gender and starting speed.
VO2 max.
NOTE: PFT means Physical Fitness Test and PRT means Physical Readiness Test.
Custom Programs
Custom Programs can be created on-the-fly by saving your routine after completion. To do this, press
Save while in Review Mode. The display will prompt you to select a program number of P01 – P09 and to
overwrite any if they already exist.
Custom Programs can be run simply by pressing the Programs key and keying in P01 – P09. Note that
these programs do not have a level or time, as these are aspects that were saved as part of the program
itself.
Operation
Page 3-9
Cybex 750T Treadmill Owner’s Manual
Alarm
During a workout session, you can set an alarm time. When this time is reached, the display will show
�ALARM’ and the console will continuously beep. Pressing Alarm, Enter or Clear will disable the alarm.
To set the alarm, press the keypad #8 (labeled with the alarm clock). Use the Speed Control Keys or the
keypad to configure the alarm time, pressing ENTER after the Hour and Minutes. See Figure 5.
Alarm
Figure 5
Fan
A built in fan is located at the top center of the console to help keep you cool during your workout. Default
speed is OFF during active mode. Press the FAN HI or FAN LO key to control fan speed. Press the FAN
OFF key to turn fan off. See Figure 6.
Fan Controls
Figure 6
Operation
Page 3-10
Cybex 750T Treadmill Owner’s Manual
Audio Visual (AV) Key Pad – Optional
Figure 7
Console Key
Description
EPG
If an Electronic Program Guide (EPG) is available, this will be displayed on
the TV. Use the CHANNEL О› V and VOLUME < > keys to navigate in the
EPG, ENTER to accept any selections, and CLEAR/EXIT to exit the EPG
mode.
CHANNEL
Toggle down or up to change channel (beeping will occur).
VOLUME
Press appropriate keys to increase or decrease volume. There is no display
interaction.
VIDEO SOURCE
Press to toggle between video source A for cable channels and video
source B for external inputs, such as iPodВ® video.
VIDEO PORT
Video capable port allows personal entertainment device or other
composite video input.
1 – Video
2 – Ground
3 – Left
4 – Right
USB PORT
Universal Serial Bus (USB) allows different devices to be connected using a
single standardized interface port for charging only.
HEAD PHONE PORT
Head phone port allows personal headphones.
Operation
Page 3-11
Cybex 750T Treadmill Owner’s Manual
Statistics
The Statistics screen allows you to track the usage and information about the treadmill. The Statistics
screen can be opened when the treadmill is not in use. Using the keyboard, press the key sequence
Clear 999 and Enter.
The ENTER key is active to advance to the next screen. The Speed control keys are active to also move
forward or backward in the menu.
The Stastics menu is as follows:
ST1 - ODOMETER
ST2 - HOURS
ST3 - STARTS
ST4 - MOVES
ST5 - ERRORS
ST6 - SERVICE
ST7 - PGM USAGE
ST1 - ODOMETER
Displayed as “KM XXXX.X” or “MI XXXX.X” where X is the total miles accumulated and units are either
Miles or Km, depending on the setup. Values range from 0.0 – 999,999.9 Miles/Km.
ST2 - HOURS
Displayed as “HOURS XXXXXX” where X is the total time the belt has run in hours. Values range from
0 – 99999
ST3 - STARTS
Displayed as “STARTS XXXXXX” where X is the number of times the belt drive started the running belt,
regardless of mode. Expect numbers from 0 – 999999
ST4 – MOVES
Displayed as “MOVES XXXXXXX” where X is the number of incline moves in 1% increments. Values
range from 0 – 9,999,999
ST5 - ERRORS
Error codes are stored in a log to inform the owner or technician of potential problems with the treadmill.
Some errors are used to track unusual conditions, like the treadmill being turned off or a power outage
while in motion. Most errors indicate a potential problem with the treadmill and can be a valuable tool in
diagnosing the cause. Any condition that may cause a hazard will disable the treadmill and show �OUT
OF ORDER’ on the console.
WARNING: All maintenance activities shall be performed by qualified personnel. Failure
to do so could result in serious injury.
NOTE: Cybex is not responsible for performing regular inspection and maintenance actions for your
treadmill. Instruct all personnel in equipment inspection and maintenance actions and also in
accident reporting/recording. Contact Cybex Customer Service at 888-462-9239 or 508-5334300 for any preventive maintenance or service concerns.
Operation
Page 3-12
Cybex 750T Treadmill Owner’s Manual
Error codes are stored in a log of 20 entries, each stamped with time and date with the most recent being
the first in the log, the oldest the last in the log. Error codes are displayed in the following format: [Log
Entry #] [Actual Error Code #] [Time] [Date], “ERR 1 141 03:49 1/14/2007”.
Press the Incline Control Keys to increment / decrement the Log count to view the next or previous error.
While displaying the error log press and hold the CLEAR button for three seconds to clear all errors. The
display will show “NO ERRORS” when cleared.
• ERROR 1 - No Speed at Startup. The display commanded a belt start but the drive did not respond
with a belt speed within timed limits.
• ERROR 3 - Speed Irregularity. The drive is reporting a slower speed than the display is commanding,
or a speed of zero after a correct speed had been established.
• ERROR 5 - Drive Communications Lost. The display lost communications with the drive, where the
drive has not given a valid response in 350 ms.
• ERROR 6 - Speed Irregularity/Overspeed. If the display has received good belt speed information at
the startup, yet the drive begins sending values outside the expected it is reported as belt speed lost.
• ERROR 7 - Controller Over-Current (Fold-back). If the display receives motor current information
from the drive that is outside of desired parameters.
• ERROR 8 - Approaching Over-Temperature. Internal controller temperature too high.
• ERROR 9 - Display watchdog triggered. If the Display Watchdog is triggered the console will reboot.
• ERROR 92 - Over Current (Output). Controller output current too high.
• ERROR 93 - Over Voltage (DC Link). Internal controller voltage too high.
• ERROR 94 - Over Heat (Heatsink). Controller temperature too high.
• ERROR 95 - Low Voltage (DC Link). Drive measures a low voltage on the input line.
• ERROR 96 - Thermal Integrator of output current. Drive measures a high current peak on the output
line.
• ERROR 98 - Display Communications lost. Without drive belt movement. The drive lost
communications with the display, where the display has not sent a valid response in 400 ms.
• ERROR 99 - Display Communications lost. With drive belt movement. The drive lost
communications with the display, where the display has not sent a valid response in 400 ms.
• ERROR 103 - Input Current OC trip (110 VAC only). Drive measures a high current peak on the input
line.
• ERROR 105 - Thermal Integrator of Input Current (110 VAC only). Input current is out of expected
range.
• ERROR 140 - Can not find home position on power-up. The display does not receive a signal from
the zero position switch during power up.
• ERROR 141 - Can not find home position in normal use. The display does not receive a signal from
the zero position switch during use.
• ERROR 142 - Out of incline range (over 15% or lower than -3%). The display receives a position
switch report that is outside of expected limits.
• ERROR 150 - Out of Speed Range (over 150hz). The display receives a report of belt speed that is
over the expected speed.
Operation
Page 3-13
Cybex 750T Treadmill Owner’s Manual
ST6 – SERVICE
Displays the count-down to the next required service in miles or kilometers remaining. Also allows for
resetting this odometer when a service has been performed.
Displayed as “SERVICE IN XXXXX MI (or KM)” where XXXXX is the distance until the next scheduled
maintenance. The odometer is set to 15,000 miles (24,140 Km). The Odometer counts down from 15,000
(24,140 Km) miles to 0 before displaying the Service message. Press and hold the CLEAR key for three
seconds while displaying the service odometer will reset it to 15,000 miles (24,140 Km).
ST7 – PGM USAGE
Each program has an individual usage meter associated with it to allow you to track frequency of use.
Displayed as “PR Y XXXXXX” where Y is the program number and XXXXX is the number of times this
program was started (program chosen, setup completed and the treadmill enters Active Mode.) Use the
Speed Control Keys to scroll through the 9 fixed and 9 custom program slots and view the number of
starts for each.
Operation
Page 3-14
Cybex 750T Treadmill Owner’s Manual
4 - Preventive Maintenance
Warnings/Cautions
All warnings and cautions listed in this chapter are as follows:
WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so
could result in serious injury.
WARNING: To prevent electrical shock, be sure that power is shut off and the treadmill is
unplugged from the electrical outlet before performing any cleaning or maintenance
procedures.
WARNING: Keep wet items away from inside parts of the treadmill. Electrical shock could occur
even if the treadmill is unplugged. Do not touch components on the lower board.
A charge can remain after unplugging the power cord and turning off the treadmill.
Regular Maintenance Activities
WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so
could result in serious injury.
Preventive maintenance activities must be performed to maintain normal operation of your treadmill.
Keeping a log sheet of all maintenance actions will assist you in staying current with all preventive
maintenance activities. See Service Schedule located at the end of this chapter.
NOTE: Worn or damaged components shall be replaced immediately or the treadmill removed from
service until the repair is made.
NOTE: Cybex is not responsible for performing regular inspection and maintenance actions for your
treadmill. Instruct all personnel in equipment inspection and maintenance actions and also in
accident reporting/recording. Contact Cybex Customer Service at 888-462-9239 or 508-5334300 for any preventive maintenance or service concerns.
Cleaning Your Treadmill
When cleaning your treadmill spray a mild cleaning agent, such as a water and dishsoap solution, on a
clean cloth first and then wipe the treadmill with the damp cloth. NOTE: Do not spray cleaning solution
directly on the treadmill. Direct spraying could cause damage to the electronics and may void the
warranty.
WARNING: To prevent electrical shock, be sure that power is shut off and the treadmill is
unplugged from the electrical outlet before performing any cleaning or maintenance
procedures.
After Each Use — Wipe up any liquid spills immediately. After each workout, use a cloth to wipe up any
remaining perspiration from the handrails and painted surfaces.
Be careful not to spill or get excessive moisture between the edge of the display panel and the console,
Preventive
Maintenance
Page 4-1
Cybex 750T Treadmill Owner’s Manual
as this might create an electrical hazard or cause failure of the electronics.
As Needed — Vacuum any dust or dirt that might accumulate under or around the treadmill. Motors are
especially susceptible to dust and dirt, and restricted airflow can prevent adequate cooling that could
shorten motor life. Cleaning this area should be done as often as indicated in the Service Schedule.
WARNING: Keep wet items away from inside parts of the treadmill. Electrical shock could occur
even if the treadmill is unplugged. Do not touch components on the lower board.
A charge can remain after unplugging the power cord.
To clean the motor components, you must loosen the four Phillips head screws that hold the motor
cover in place. Lift the cover straight up; the screws and side covers will stay in place. Use a vacuum
attachment or hand vacuum to clean the exposed elevation assembly, drive motor, lower electronics and
the surrounding areas.
Also use a dry cloth for the areas that you can not reach with the vacuum cleaner. If the machine has not
been used for some time or is excessively dirty, use a dry cloth to wipe all exposed areas.
Carefully raise the rear of the treadmill and roll it back from its present position to vacuum the floor area
underneath the unit. When finished, return the treadmill to its normal position.
Contact Heart Rate Grips — Contaminants, such as hand lotions, oils or body powder, may come off
on the contact heart rate grips. These can reduce sensitivity and interfere with the heart rate signal. It is
recommended that the user have clean hands when using the contact heart rate. Clean the grips using
a cloth dampened with a cleaning solution containing rubbing alcohol. The grips are the only part of the
treadmill you should use a cleaning solution containing rubbing alcohol.
Preventive
Maintenance
Page 4-2
Cybex 750T Treadmill Owner’s Manual
Running Belt Maintenance
Belt and Deck — Wipe the belt surface and the deck area with a clean dry towel to minimize the effect
of friction between the deck and the running belt. This should be done often to prevent premature wear of
the deck, running belt, and the drive motor system. See the Service Schedule at the end of this chapter.
The running belt may become loose and slip on the drive roller with each foot plant. If it does, follow
the Tensioning and Centering the Belt procedure below. See the Service Schedule in this chapter for a
minimum schedule for checking the belt tension.
Tension and Center the Belt — If the belt is slipping under each step perform this procedure:
Tools Required
• 3/4” Socket wrench
1. Tension the belt.
A. Use a 3/4” socket wrench to turn each bolt 1/2 turn clockwise. See Figure 1.
NOTE: Be sure to adjust each bolt equally on each side.
Figure 1
B. Press the Quick Start key.
C. Press the Speed + to bring the speed up to 3.5-4 mph (5.6-6.4 kph). Allow the treadmill to run for
a minute.
D. Observe the belt to be sure it stays centered. If it is not centered follow step 2.
E. Walk on the belt to see if it still slips. If it does restart this procedure at step 1 A. If you have to do
this procedure three times and it still slips call Cybex Customer Service. Follow the next step to
be sure the belt is centered.
NOTE: Be careful not to over tighten the belt. Over tightening the belt can cause the belt to stretch and
require replacement.
Preventive
Maintenance
Page 4-3
Cybex 750T Treadmill Owner’s Manual
2. Center the belt.
NOTE: While centering the belt choose one bolt to adjust. Do not adjust both bolts.
A. With the treadmill running at 5 mph (8 kph) observe the running belt. If the belt tracks off center to
the right or left, the deck will become exposed. Use a 3/4” socket wrench to tighten the rear roller
bolt on the side of the treadmill toward which the belt is moving. For example: If the belt moves to
the right and the deck becomes exposed on the left, tighten the bolt on the right side of the frame,
tighten about 1/2 of a turn (clockwise) and wait 30 seconds. If the belt does not move back to the
center of the treadmill, make another adjustment to the same bolt. Once the running belt has
been adjusted closer to the center of the treadmill, use about 1/4 of a turn until the belt has been
stabilized.
B. After the belt has been centered, check the belt tension again. Make sure the running belt tension
is tight enough so that the belt does not slip or hesitate when stepped on. Walk on the treadmill
at 3.5-4 mph (5.6-6.4 kph) and every 4th to 5th step throw your weight into your step to feel if the
belt is slipping. If the belt does slip, use a wrench to equally tighten both rear roller adjustment
bolts 1/2 of a turn (clockwise). Adjust the belt until no further slipping is felt.
Checking the Belt and Deck Surfaces — The running belt and deck should be checked periodically for
any excessive wear. In an effort to make sure that the running belt operates properly, visually inspect the
belt often to make sure that there are no tears or fraying in the belt material. The running belt should be
replaced and the running deck flipped every 15,000 miles (24,140 km). A service prompt will appear at
this interval and the parts will need to be replaced.
Inspect the edges of the belt as described below.
Tools Required
• None
1. Disconnect the external power source.
A. Turn the main power switch on the front of the unit to the off (O) position.
B. Unplug the treadmill from the power outlet.
2. Check the belt and deck condition.
A. Look at the edges of the belt while you roll it by hand. If the belt has any rips or looks excessively
worn the belt needs to be replaced.
B. Run your hand under the belt on the top of the deck surface. If you feel excessive ridges or
cracks, or if any wood is exposed under the black surface, the deck should be replaced. In time, a
worn belt and deck can cause high current draw and ultimately, motor failure.
NOTE: If the running belt and deck need replacement refer to a qualified service technician.
Preventive
Maintenance
Page 4-4
Cybex 750T Treadmill Owner’s Manual
Other Preventive Maintenance
Other preventive maintenance activities must be completed by a qualified service technician at the
recommended intervals listed in the Service Schedule at the end of this chapter. These activities include:
• Replace the running deck
• Replace the running belt
Elevation Motor Lubrication — In time the elevation motor pivot points may develop a squeak.
Lubricate the upper and lower bolts and the spacers with a small amount of lithium grease. NOTE: You
can buy lithium grease at an auto parts store.
Static Electricity — Depending upon where you live, you may experience dry air, causing a common
experience of static electricity. This may be especially true in the winter time. You may notice a static
build-up just by walking across a carpet and then touching a metal object. The same can hold true while
working out on your treadmill. You may experience a shock due to the build-up of static electricity on your
body and the discharge path of the treadmill. If you experience this type of situation, you may want to
increase the humidity to a comfortable level through the use of a humidifier.
Preventive
Maintenance
Page 4-5
Cybex 750T Treadmill Owner’s Manual
Service Schedule
All maintenance activities shall be performed by qualified personnel. Failure to do so could result in
serious injury.
NOTE: This is the minimum recommended service.
1. Determine mileage.
A. While in Dormant Mode enter Statistics Mode by pressing the sequence CLEAR 999 and
ENTER. The ENTER key is active to advance to the next screen. The SPEED control keys are
also active to move forward or backwards in the menu.
B. Press the SPEED control keys to display “6-SERVICE” and miles or kilometers to the next
required service will be displayed.
C. Record Mileage. NOTE: Displays the count-down mileage to the next required service. Mileage
start at 15,000 miles (24,140 Km) and counts down to 0.
NOTE: To exit Statistics Mode, press the CLEAR key .
First 500 miles (800 km).
• Check running belt tension and tracking.
Every 5,000 miles (8,000 km).
• Check running belt tension and tracking.
• Move treadmill and vacuum underneath.
• Raise elevation to 15%, carefully tip treadmill up on the console to clean underneath with a dry cloth
and vacuum. Return to normal position when done.
Every 15,000 miles (24,140 km).
• Replace running belt and flip deck.
• Check elevation assembly and replace worn parts.
• Lubricate elevation pivot points.
Every 30,000 miles (48,280 km).
• Replace running belt and deck.
2. Resetting the service odometer.
A. While in Dormant Mode enter Statistics Mode by pressing the sequence CLEAR 999 and
ENTER. The ENTER key is active to advance to the next screen. The SPEED control keys are
also active to move forward or backwards in the menu.
B. Press the SPEED control keys to display “6-SERVICE” and miles or kilometers to the next
required service will be displayed.
C. Press and hold the CLEAR key for three seconds to reset the service odometer to 15,000 miles
(24,140 km).
NOTE: Service may be performed before the 15,000 miles (24,140 km) service prompt appears. Perform
the service on the unit and follow the above procedure to reset the service odometer to zero.
Preventive
Maintenance
Page 4-6
Cybex 750T Treadmill Owner’s Manual
Displays the count-down to the next required service in miles remaining. Also allows for resetting this
odometer of a service has been performed.
Displayed as “SERVICE IN XXXXX MI (or KM)” where XXXXX is the distance until the next scheduled
maintenance. The odometer is set to 15,000 miles (24,140 Km). The Odometer counts down from
15,000 (24,140 Km) miles to 0 before displaying the Service message. Press and hold the CLEAR key
for three seconds while displaying the service odometer will reset it to 15,000 miles (24,140 Km).
Preventive
Maintenance
Page 4-7
Cybex 750T Treadmill Owner’s Manual
This page intentionally left blank
Preventive
Maintenance
Page 4-8
Cybex 750T Treadmill Owner’s Manual
5 - Customer Service
Contacting Service
Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard Time.
For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239.
For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax
508-533-5183.
Serial Number and Voltage
Your serial number and voltage can be found on the rear of your treadmill. See Figure 1. For your
convenience, record your serial number and voltage below so that you will have it ready if you call Cybex
Customer Service.
Serial Number
Voltage
Serial
Number
Figure 1
Customer
Service
Page 5-1
Cybex 750T Treadmill Owner’s Manual
Return Material Authorization (RMA)
The Return Material Authorization (RMA) system outlines the procedures to follow when returning
material for replacement, repair, or credit. The system assures that returned materials are properly
handled and analyzed. Perform the following procedures carefully.
Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will
request an RMA from Cybex, if applicable. Under no circumstances will defective parts or equipment be
accepted by Cybex without proper RMA and an Automated Return Service (ARS) label.
1. Call the Customer Service Hotline listed above for the return of any item that is defective.
2. Provide the technician with a detailed description of the problem you are having or the defect in the
item you wish to return.
3. Provide the model and serial number of your treadmill. The serial number is located on the front panel
of your treadmill. The serial number begins with a letter, for example: R09-101331100.
4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for
evaluation and repair or replacement. The technician will assign you an RMA number and will send
you an ARS label. The ARS label and RMA number must be clearly displayed on the outside of the
package that contains the item(s) to be returned. Include a description of the problem, the serial
number of the treadmill and the name and address of the owner in the package along with the part(s).
5. Forward the package through UPS to Cybex.
Attn: Customer Service Department
Cybex International, Inc.
10 Trotter Drive
Medway, MA 02053
NOTE: Merchandise returned without an RMA number on the outside of the package or shipments sent
C.O.D. will not be accepted by the Cybex receiving department.
Damaged Parts
Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility
of the carrier (UPS, Federal Express, trucking companies, etc.).
Apparent Damage — Upon receipt of your shipment, check all boxes carefully. Any damage seen with a
visual check must be noted on the freight bill and signed by the carrier’s agent. Failure to do so will result
in the carrier’s refusal to honor your damage claim. The carrier will provide you with the required forms for
filing such claims.
Concealed Damage — Damage not seen with a visual check upon receipt of a shipment but noticed
later must be reported to the carrier as soon as possible. Upon discovery of the damage, a written or
phone request to the carrier asking them to perform an inspection of the materials must be made within
ten days of the date of delivery. Keep all shipping containers and packing materials, they will be needed
as part of the inspection process. The carrier will provide you with an inspection report and the necessary
forms for filing a concealed damage claim. Concealed damage is the carrier’s responsibility.
Customer
Service
Page 5-2
Cybex 750T Treadmill Owner’s Manual
Ordering Parts
Fax your order to 508-533-5183. To speak with a customer service representative, call
888-462-9239 (for customers living within the USA) or 508-533-4300 (for customers outside
the USA)..
CAUTION
Use only Cybex replacement
parts when servicing.
Failure to do so could result
in personal injury.
Cybex will void warranty if
non-Cybex replacement parts
are used.
Customer
Service
Page 5-3
Cybex 750T Treadmill Owner’s Manual
This page intentionally left blank
Customer
Service
Page 5-4
Cybex 750T Treadmill Owner’s Manual
Appendix A - Technical Specifications
Specifications
Length:
80” (204 cm).
Width:
34” (86 cm).
Running Area:
22” x 62” (56 cm x 157 cm).
Weight of Product:
410 lbs. (186 kg).
Shipping Weight
440 lbs. (200 kg).
Speed Range:
0.5 to 15.6 mph (0.8 to 25.1 kph) in 0.1 mph or 0.1 kph increments. Default Max Speed is
12.4 mph (20.0 kph).
Incline Range:
-3 to 15% grade.
Manual Mode:
Yes.
Programs:
Quick Start plus Manual, Weight Loss, Rolling Hills, Hills, Pikes Peak, Hill Interval 1:1,
Hill Interval 1:2, Hill Interval 1:3, Cardio, HR Control, eight Fitness Tests and nine Custom
Programs.
Standard Features:
Safety Sentryв„ў, Contact Heart Rate, PolarВ® wireless heart rate (chest strap not included),
CSAFE, frame color choices include white texture, black texture, metaltone gold, black chrome
and platinum sparkle.
Optional Features:
Unlimited custom colors available.
Power Requirement: Grounded, single phase, dedicated line (discreet power and return for each circuit) and one of the
following:
• 100 VAC, 50/60 Hz, 20A.
• 115 VAC, 60 Hz, 20A.
• 220 VAC, 60 Hz, 15A.
• 230 VAC, 50 Hz, 15A.
• 230 VAC, 50 Hz, 13A.
Motor:
3.0 hp Continuous, 6.0 hp Peak, AC, Brushless.
Emergency Stop:
Pull the emergency stop key (e-stop).
Maximum User Weight: 400 lbs. (181 kg).
Options:
Embedded A/V channel and volume controls and video mount bracket.
34”
(86 cm)
80” (204 cm)
Specifications
Page A-1
Cybex 750T Treadmill Owner’s Manual
This page intentionally left blank
Specifications
Page A-2
Cybex 750T Treadmill Owner’s Manual
Appendix B – Program Overviews
Manual
Program Overview
Manual Mode is available both through Quick Start and through the Manual program where you are
prompted to enter Time and Weight. NOTE: There is no diagram because incline and speed are usercontrolled.
Manual Mode allows you to choose settings as you workout. You may choose your settings according to
how you feel or your endurance level. Since you remain in control, Manual Mode may be the best choice
for beginners or for those who have not worked out in a long time. You select the time of your workout.
NOTE: Manual Mode is not a pre-programmed workout.
Press the Quick Start key to workout in Manual Mode. You can also begin Manual Mode by pressing the
Manual program key. To increase or decrease the speed while in Manual Mode use the Speed + – keys.
To increase or decrease the incline while in Manual Mode use the
arrows. Time counts up, you can
end your session at any time.
NOTE: A Manual workout session using QuickStart will display time counting up to the configured MAX
TIME. A Manual workout session using the Manual key selection will prompt for a session time
and will then count down from that time to reach that goal.
Programs
The programs used in the 750T Treadmill (with the exception of Heart Rate Control, Gerkin Protocol
(FT1) and potential custom programs), are all incline driven programs where the user has complete
control of their speed throughout the entire session.
Individuals can tailor the use of program level and speed selection to meet their own needs. For example,
if an individual is not comfortable running, they can choose a slower speed in conjunction with a high
program level for increased demand. A runner can choose a comfortable running speed in conjunction
with a lower program level to mimic real world elevation changes.
The last two minutes of a Programs (P1 – P9) will reduce the incline to 0% and the speed to half of the
MET level for each of the two remaining minutes (see Cool Down in Terms and Symbols Used).
Program changes on-the-fly
During any active mode, press the Program key and select a program using program options. User
speed and time are maintained. The warm up period is skipped and the first segment of the program will
start using the program entered.
Program
Overviews
Page B-1
Cybex 750T Treadmill Owner’s Manual
Weight Loss (P-1)
Program Overview
The Weight Loss program uses a series of relatively minor changes in its five-minute core to add an
incremental demand. The five-minute core utilizes a baseline incline for two minutes and then increases
the incline for added demand and then provides a slightly lower Incline for two-minutes for recovery. See
table below and Figure 1.
Time
Incline
10
9
8
7
6
5
4
3
2
1
Figure 1
Program
Overviews
Page B-2
:30 :30
Warm Up
1
2
2
3
2
3
2
2
2
2
1
2
1
2
1
1
1
1
1
1
1
1
:30
:30
3
3
3
3
3
2
2
2
2
1
1
4
5
5
4
4
3
3
2
2
2
2
1:00 1:00 1:00 1:00
Program Segments
1
2
3
4
10
10
14
9
9
9
12
8
8
8
10
7
7
7
9
6
6
6
7
5
5
5
6
4
4
4
5
3
3
3
4
2
2
2
3
1
1
1
2
0
1:00
5
9
8
7
6
5
4
3
2
1
0
:30
:30
Cool Down
1
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:30
:30
3
0
0
0
0
0
0
0
0
0
0
4
0
0
0
0
0
0
0
0
0
0
Cybex 750T Treadmill Owner’s Manual
Rolling Hills (P-2)
Program Overview
The Rolling Hills program uses an eight-minute core intended to mimic variety in terrain that might
be found on a hilly outdoor run. The eight minute core is composed of four segments. The baseline
segment is two minutes in length and is followed by two, two-minute segments of increased incline before
returning to the intermediate incline for two-minutes. See table below and Figure 2.
Time
Incline
10
9
8
7
6
5
4
3
2
1
:30 :30
Warm Up
1
2
1
2
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
:30
:30
3
2
2
2
1
1
1
1
0
0
0
4
3
2
2
2
2
1
1
0
0
0
2:00 2:00 2:00 2:00
Program Segments
1
2
3
4
4
6
8
6
3
6
8
5
3
5
8
5
2
5
7
4
2
4
7
4
1
4
7
3
1
3
6
3
0
3
6
3
0
2
6
2
0
2
5
2
:30
:30
Cool Down
1
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:30
:30
3
0
0
0
0
0
0
0
0
0
0
4
0
0
0
0
0
0
0
0
0
0
Figure 2
Program
Overviews
Page B-3
Cybex 750T Treadmill Owner’s Manual
Hills (P-3)
Program Overview
The Hills program uses a six minute core utilizing one minute segments with mild incline changes and
two relative peak segments followed by relative rest segments. See table below and Figure 3.
Time
Incline
10
9
8
7
6
5
4
3
2
1
Figure 3
Program
Overviews
Page B-4
:30 :30
Warm Up
1
2
3
3
2
3
2
3
2
2
1
2
1
1
1
1
0
0
0
0
0
0
:30
:30
3
5
4
3
3
2
2
1
1
0
0
4
6
5
5
4
3
2
2
1
0
0
1:00 1:00 1:00 1:00
Program Segments
1
2
3
4
8
10
12
10
7
9
12
9
6
8
11
8
5
7
10
7
4
6
9
6
3
5
8
5
2
4
7
4
1
3
6
3
0
2
5
3
0
2
4
2
1:00
1:00
5
15
14
13
12
11
10
9
8
7
6
6
10
9
8
7
6
5
4
3
3
2
:30
:30
Cool Down
1
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:30
:30
3
0
0
0
0
0
0
0
0
0
0
4
0
0
0
0
0
0
0
0
0
0
Cybex 750T Treadmill Owner’s Manual
Pikes Peak (P-4)
Program Overview
Pikes Peak uses a nine minute core where the incline increases every minute for the first five minutes.
After the fifth minute of the core program, the incline is reduced each minute. This program uses
continuous and gradual changes to give the user time to acclimate to demand and recover without large
perceived changes in the effort required. See table below and Figure 4.
Time
:30
:30
:30
:30
Warm Up
Incline
1:00
1:00
1:00
1:00
1:00
1:00
1:00
1:00
1:00
Program Segments
:30
:30
:30
:30
Cool Down
1
2
3
4
1
2
3
4
5
6
7
8
9
1
2
3
4
10
2
2
3
4
5
8
11
13
15
13
11
8
5
0
0
0
0
9
1
2
2
3
4
7
10
12
14
12
10
7
4
0
0
0
0
8
1
2
2
3
4
6
9
11
13
11
9
6
4
0
0
0
0
7
1
1
2
2
3
5
8
10
12
10
8
5
3
0
0
0
0
6
1
1
2
2
3
5
7
9
11
9
7
5
3
0
0
0
0
5
1
1
1
2
2
4
6
8
10
8
6
4
2
0
0
0
0
4
1
1
1
2
2
3
5
7
9
7
5
3
2
0
0
0
0
3
1
1
1
2
2
3
4
6
8
6
4
3
2
0
0
0
0
2
0
0
1
1
1
2
3
5
7
5
3
2
1
0
0
0
0
1
0
0
0
0
0
1
2
4
6
4
2
1
0
0
0
0
0
Figure 4
Program
Overviews
Page B-5
Cybex 750T Treadmill Owner’s Manual
Hill Interval 1:1 (P-5)
Program Overview
This program is designed to increase capability by alternating two minute work segments with two
minutes of relative rest. The intensity of rest periods is greater here than in Hill Interval 1:2 as is the
duration of the work interval making this program more demanding than Hill Interval 1:2. See table below
and Figure 5.
Time
Incline
10
9
8
7
6
5
4
3
2
1
Figure 5
Program
Overviews
Page B-6
:30 :30
Warm Up
1
2
3
5
3
4
3
4
3
3
2
3
2
3
2
2
1
2
1
1
1
1
:30
:30
3
6
6
5
5
4
3
3
2
2
1
4
8
8
7
6
5
5
4
3
2
2
1:00 1:00 1:00 1:00
Program Segments
1
2
3
4
11
11
6
6
10
10
5
5
9
9
5
5
8
8
4
4
7
7
4
4
6
6
3
3
5
5
3
3
4
4
2
2
3
3
2
2
2
2
1
1
:30 :30
Cool Down
1
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:30
:30
3
0
0
0
0
0
0
0
0
0
0
4
0
0
0
0
0
0
0
0
0
0
Cybex 750T Treadmill Owner’s Manual
Hill Interval 1:2 (P-6)
Program Overview
This program is designed with a one minute work interval at a high incline followed by a two minute rest
interval at a substantially lower incline. Given the lower incline and longer rest intervals this program is
less intense than Hill Interval 1:1. See table below and Figure 6.
Time
:30
Incline
10
9
8
7
6
5
4
3
2
1
Warm Up
1
2
3
5
3
4
3
4
3
3
2
3
2
3
2
2
1
2
1
1
1
1
:30
:30
:30
3
6
6
5
5
4
3
3
2
2
1
4
8
8
7
6
5
5
4
3
2
2
1:00 1:00
Program
Segments
1
2
11
4
10
3
9
3
8
3
7
2
6
2
5
2
4
1
3
1
2
1
1:00
3
4
3
3
3
2
2
2
1
1
1
:30
:30
Cool Down
1
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:30
:30
3
0
0
0
0
0
0
0
0
0
0
4
0
0
0
0
0
0
0
0
0
0
Figure 6
Program
Overviews
Page B-7
Cybex 750T Treadmill Owner’s Manual
Hill Interval 1:3 (P-7)
Program Overview
Hill Interval 1:3 utilizes a one minute work interval followed by a three minute rest interval. The rest
intervals are of a higher incline than those found in the other Hill Interval programs, and therefore require
a longer recovery period. See table below and Figure 7.
Time
Incline
10
9
8
7
6
5
4
3
2
1
Figure 7
Program
Overviews
Page B-8
:30 :30
Warm Up
1
2
3
5
3
4
3
4
3
3
2
3
2
3
2
2
1
2
1
1
1
1
:30
:30
3
6
6
5
5
4
3
3
2
2
1
4
8
8
7
6
5
5
4
3
2
2
1:00 1:00 1:00 1:00
Program Segments
1
2
3
4
11
7
7
7
10
7
7
7
9
6
6
6
8
5
5
5
7
5
5
5
6
4
4
4
5
3
3
3
4
3
3
3
3
2
2
2
2
1
1
1
:30
:30
Cool Down
1
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:30
:30
3
0
0
0
0
0
0
0
0
0
0
4
0
0
0
0
0
0
0
0
0
0
Cybex 750T Treadmill Owner’s Manual
Cardio (P-8)
Program Overview
The Cardio program is designed to maintain a high total demand using two four-minute segments of
alternating incline. This allows prolonged intervals that take advantage of long term energy systems
and total aerobic capability when associated with speeds that require a high sustained cardiovascular
demand. See table below and Figure 8.
Time
:30
Incline
10
9
8
7
6
5
4
3
2
1
Warm Up
1
2
2
3
2
3
2
3
2
2
2
2
2
2
2
2
1
2
0
0
0
0
:30
:30
:30
3
3
3
3
3
3
3
3
2
1
0
4
5
5
5
4
4
4
4
3
2
0
4:00
4:00
Program
Segments
1
2
11
9
10
8
9
7
8
6
7
5
6
4
5
3
4
2
3
1
2
0
:30
:30
Cool Down
1
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:30
:30
3
0
0
0
0
0
0
0
0
0
0
4
0
0
0
0
0
0
0
0
0
0
Figure 8
Program
Overviews
Page B-9
Cybex 750T Treadmill Owner’s Manual
HR Control (P-9)
NOTE: To use this feature, a PolarВ® compatible heart rate transmitter belt (not included) must be worn.
Program Overview
The Heart rate Control program is interactive. By selecting a predetermined heart rate, the treadmill will
adapt the elevation and speed to keep the user’s heart rate at that level. This program is exceptionally
useful for those individuals just starting out as well as the athlete. By maintaining the predetermined heart
rate, the user is less likely to over or under exert themselves thereby ensuring they get all they should
out of their training. Over time, the user will notice that as their fitness level improves and using a given
time and heart rate that they will see more ground covered, more calories burned and a higher MET level
during the program.
A MET is a basic unit of measurement that is used to compare relative work between individuals and
activities. One MET is the amount of oxygen an individual consumes at rest. If an individual were working
at four METs, he/she would be consuming oxygen at a rate equal to four times their resting consumption
METs can be used to compare walking on a grade with running or even to cycling and other activities.
Gerkin Protocol (FT1)
Program Overview
This program was designed to predict the VO2 max using the Gerkin protocol. This test is used by the
International Association of Firefighters to evaluate fitness level.
The speed range of the program includes walking speeds at 3 MPH then increases to 4.5 MPH or more
during the middle stages. It returns to 3 MPH during the cool down session.
Elevation is used during the second stage of the test. It starts at a 2% grade and can increase from there.
Input information:
Age
Weight
Gender
Heart rate (PolarВ® compatible wireless chest strap required)
Test procedure:
1. 3 minute warm-up at 0% grade, 3mph.
2. Stage 1 – 1 minute, 0% grade, 4.5 mph. Walk or run. Heart rate is recorded during the last 15
seconds of each stage.
3.
Stage 2 – 1 minute, 2% grade, 4.5 mph.
• Speed and grade increases now alternate. At odd numbered stages, speed increases by 0.5 mph.
At even numbered stages, grade increases 2%.
• If heart rate is 85% or above, the stage is recorded, but the test continues for another 15 seconds
with no increase in grade or speed.
• If heart rate remains above 85%, the test is terminated, and the last stage number is entered.
• If heart rate falls to or below 85%, speed or gradient is increased on the next minute boundary.
• Once the 85% threshold is exceeded or makes it to the 11th minute, the evaluation is ended and the
final stage is entered
4.
3 minute Cool-down – 0% grade, 3 mph.
5. Take heart rate and record one minute after the end of the test. (Taken as a final reading and to
monitor HR stabilizing).
Test Result:
FT1 – �GERKIN PROTOCOL PREDICTED VO2 MAX = XXX’
Program
Overviews
Page B-10
Cybex 750T Treadmill Owner’s Manual
Army (FT2)
Program Overview
This program was designed by the Army to test, evaluate and measure fitness levels. The goal is to
complete the set distance of 2.0 miles (3.2 km) in the least amount of time. The user controls the speed
as needed to reach the goal. A point value will be given at the completion of the test. See Figure 9.
Input information:
Age
Weight
Gender
Starting Speed
Test Result:
FT2 – �ARMY PFT SCORE = XXX’
ARMY
Male
Age
17-21
22-26
27-31
32-36
37-41
42-46
47-51
52-56
57-61
62+
Score
100
13:00
13:00
13:18
13:18
13:36
14:06
14:24
14:42
15:18
15:42
90
13:42
13:54
14:12
14:24
14:48
15:12
15:42
16:00
16:24
16:48
80
14:24
14:48
15:06
15:30
16:00
16:24
16:54
16:54
17:36
17:48
70
15:12
15:42
16:06
16:36
17:06
17:36
18:12
18:30
18:42
18:54
60
15:54
16:36
17:00
17:42
18:18
18:42
19:30
19:48
19:54
20:00
50
16:36
17:30
17:54
18:48
19:30
19:48
20:48
21:00
21:06
21:06
40
17:18
18:24
18:48
19:54
20:42
21:00
22:00
22:18
22:12
22:12
30
18:06
19:18
19:48
21:00
21:48
22:06
23:18
23:36
23:18
23:12
20
18:48
20:12
20:42
22:06
23:00
23:18
24:36
24:54
24:30
24:18
10
19:30
21:06
21:36
23:12
48:12
24:24
25:54
26:12
25:36
25:24
Score
100
15:36
15:36
15:48
15:54
17:00
17:24
17:36
19:00
19:42
20:00
90
16:24
16:36
17:00
17:18
18:24
18:54
19:12
20:18
21:00
21:18
80
17:12
17:36
18:06
18:48
19:54
20:30
20:48
21:42
22:18
22:30
70
18:06
18:36
19:18
20:12
21:18
22:06
22:24
23:00
23:30
23:42
60
18:54
19:36
20:30
21:42
22:42
23:42
24:00
24:24
24:48
25:00
50
19:42
20:36
21:42
23:06
24:06
25:12
25:36
25:48
26:06
26:12
40
20:30
21:36
22:48
24:36
25:30
30
21:24
22:36
24:00
26:00
20
22:12
23:36
25:12
10
23:00
24:36
26:24
Female
Age
17-21
22-26
27-31
32-36
37-41
42-46
47-51
52-56
57-61
62+
Figure 9
Program
Overviews
Page B-11
Cybex 750T Treadmill Owner’s Manual
Air Force (FT3)
Program Overview
This program was designed by the Air Force to test, evaluate and measure fitness levels. The goal is to
complete the set distance of 1.5 miles (2.4 km) in the least amount of time. The user controls the speed
as needed to reach the goal. A point value will be given at the completion of the test. See Figures 10, 11
and 12.
Input information:
Age
Weight
Gender
Starting Speed
Test Result:
FT3 – �AIRFORCE PFT SCORE = XXX’
Males <25 & Males 25-29
Males 30-34 & Males 35-39
Males 40-44 & Males 45-49
VO2
(ml/kg/min)
1.5-Mile Run Submaximal
Time (min.)
Estimates
VO2
(ml/kg/min)
1.5-Mile Run Submaximal
Time (min.)
Estimates
VO2
(ml/kg/min)
1.5-Mile Run Submaximal
Time (min.)
Estimates
Component
Points
Component
Points
<9:36
>54
50.00
<9:48
53
50.00
<10:24
>50
50.00
9:36
54
50.00
9:48
53
50.00
10:24
50
50.00
9:37-9:48
53
47.50
9:49-10:12
51-52
47.50
10:25-10:36
49
47.50
9:49-10:12
51-52
45.00
10:13-10:24
50
45.00
10:37-10:54
48
45.00
10:13-10:36
49-50
43.50
10:25-10:54
48-49
43.50
10:55-11:24
46-47
43.50
10:37-11:06
47-48
42.00
10:55-11:24
46-47
42.00
11:25-11:54
44-45
42.00
11:07-11:36
45-46
40.50
11:25-11:54
44-45
40.50
11:55-12:30
42-43
40.50
11:37-12:12
43-44
39.00
11:55-12:30
42-43
39.00
12:31-13:12
40-41
39.00
12:13-12:54
41-42
37.50
12:31-12:54
41
37.50
13:13-13:36
39
37.50
12:55-13:36
39-40
36.00
12:55-13:36
39-40
36.00
13:37-14:24
37-38
36.00
13:37-14:24
37-38
34.00
13:37-14:24
37-38
34.00
14:25-15:18
35-36
34.00
14:25-14:54
36
32.00
14:25-14:54
36
32.00
15:19-15:48
34
32.00
14:55-15:18
35
30.00
14:55-15:18
35
30.00
15:49-16:24
33
30.00
15:19-15:48
34
27.00
15:19-15:48
34
27.00
16:25-16:54
32
27.00
15:49-16:24
33
24.00
15:49-16:24
33
24.00
16:55-17:36
31
24.00
16:25-16:54
32
21.00
16:25-16:54
32
21.00
17:37-18:12
30
21.00
16:55-17:36
31
18.00
16:55-17:36
31
18.00
18:13-18:54
29
18.00
17:37-18:12
30
15.00
17:37-18:12
30
15.00
18:55-19:42
28
15.00
18:13-18:54
29
12.00
18:13-18:54
29
12.00
19:43-20:36
27
12.00
18:55-19:42
28
9.00
18:55-19:42
28
9.00
20:37-21:30
26
9.00
19:43-20:36
27
6.00
19:43-20:36
27
6.00
21:31-22:30
25
6.00
20:37-21:30
26
3.00
20:37-21:30
26
3.00
22:31-23:36
24
3.00
>21:30
<26
0.00
>21:30
<26
0.00
>23:36
<24
0.00
Figure 10
Program
Overviews
Page B-12
Component
Points
Cybex 750T Treadmill Owner’s Manual
Air Force (FT3) continued
Males 50-54 & Males 55+
Males 40-44 & Males 45-49
Males 50-54 & Males 55+
VO2
(ml/kg/min)
1.5-Mile Run Submaximal
Time (min.)
Estimates
VO2
(ml/kg/min)
1.5-Mile Run Submaximal
Time (min.)
estimates
VO2
(ml/kg/min)
1.5-Mile Run Submaximal
Time (min.)
Estimates
>11:06
>47
Component
Points
50.00
<10:24
>50
Component
Points
50.00
>11:06
>47
Component
Points
50.00
11:06
47
50.00
10:24
50
50.00
11:06
47
50.00
11:07-11:24
46
47.50
10:25-10:36
49
47.50
11:07-11:24
46
47.50
11:25-11:36
45
45.00
10:37-10:54
48
45.00
11:25-11:36
45
45.00
11:37-12:12
43-44
43.50
10:55-11:24
46-47
43.50
11:37-12:12
43-44
43.50
12:13-12:54
41-42
42.00
11:25-11:54
44-45
42.00
12:13-12:54
41-42
42.00
12:55-13:36
39-40
40.50
11:55-12:30
42-43
40.50
12:55-13:36
39-40
40.50
13:37-14:24
37-38
39.00
12:31-13:12
40-41
39.00
13:37-14:24
37-38
39.00
14:25-15:18
35-36
37.50
13:13-13:36
39
37.50
14:25-15:18
35-36
37.50
15:19-15:48
34
36.00
13:37-14:24
37-38
36.00
15:19-15:48
34
36.00
15:49-16:54
32-33
34.00
14:25-15:18
35-36
34.00
15:49-16:54
32-33
34.00
16:55-17:36
31
32.00
15:19-15:48
34
32.00
16:55-17:36
31
32.00
17:37-18:12
30
30.00
15:49-16:24
33
30.00
17:37-18:12
30
30.00
18:13-18:54
29
27.00
16:25-16:54
32
27.00
18:13-18:54
29
27.00
18:55-19:42
28
24.00
16:55-17:36
31
24.00
18:55-19:42
28
24.00
19:43-20:36
27
21.00
17:37-18:12
30
21.00
19:43-20:36
27
21.00
20:37-21:30
26
18.00
18:13-18:54
29
18.00
20:37-21:30
26
18.00
21:31-22:30
25
15.00
18:55-19:42
28
15.00
21:31-22:30
25
15.00
22:31-23:36
24
12.00
19:43-20:36
27
12.00
22:31-23:36
24
12.00
23:37-24:48
23
9.00
20:37-21:30
26
9.00
23:37-24:48
23
9.00
24:49-26:06
22
6.00
21:31-22:30
25
6.00
24:49-26:06
22
6.00
26:07-27:36
21
3.00
22:31-23:36
24
3.00
26:07-27:36
21
3.00
>27:36
<21
0.00
>23:36
<24
0.00
>27:36
<21
0.00
Figure 11
Program
Overviews
Page B-13
Cybex 750T Treadmill Owner’s Manual
Air Force (FT3) continued
Program
Overviews
Page B-14
Females <25
Females 25-29
VO2 (ml/kg/min
1.5-Mile Run Submaximal Component
Time (min.)
Estimates
Points
VO2 (ml/kg/min)
1.5-Mile Run Submaximal Component
Time (min.)
Estimates
Points
<11:06
>47
50.00
<11:24
>46
50.00
11:06
47
50.00
11:24
46
50.00
11:07-11:36
45-46
47.50
11:25-11:36
45
47.50
11:37-11:54
44
45.00
11:37-11:54
44
45.00
11:55-12:30
42-43
43.50
11:55-12:30
42-43
43.50
12:31-13:12
40-41
42.00
12:31-13:12
40-41
42.00
13:13-14:00
38-39
40.50
13:13-14:00
38-39
40.50
14:01-14:54
36-37
39.00
14:01-14:54
36-37
39.00
14:55-15:18
35
37.50
14:55-15:18
35
37.50
15:19-15:48
34
36.00
15:19-15:48
34
36.00
15:49-16:24
33
34.00
15:49-16:24
33
34.00
16:25-16:54
32
32.00
16:25-16:54
32
32.00
16:55-17:36
31
30.00
16:55-17:36
31
30.00
17:37-18:12
30
27.00
17:37-18:12
30
27.00
18:13-18:54
29
24.00
18:13-18:54
29
24.00
18:55-19:42
28
21.00
18:55-19:42
28
21.00
19:43-20:36
27
18.00
19:43-20:36
27
18.00
20:37-21:30
26
15.00
20:37-21:30
26
15.00
21:31-22:30
25
12.00
21:31-22:30
25
12.00
22:31-23:36
24
9.00
22:31-23:36
24
9.00
23:37-24:48
23
6.00
23:37-24:48
23
6.00
24:49-26:06
22
3.00
24:49-26:06
22
3.00
>26:06
<22
0.00
>26:06
<22
0.00
Females 30-34 & Females 35-39
Females 40-44 & Females 45-49
Females 50-54 & Females 55+
VO2 (ml/kg/min)
1.5-Mile Run Submaximal Component
Time (min.)
Estimates
Points
VO2 (ml/kg/min)
1.5-Mile Run Submaximal Component
Time (min.)
Estimates
Points
VO2(ml/kg/min)
1.5-Mile Run Submaximal Component
Time (min.)
Estimates
Points
<11:54
>44
50.00
<12:30
>42
50.00
<14:24
>37
50.00
11:54
44
50.00
12:30
42
50.00
14:24
37
50.00
11:55-12:30
42-43
47.50
12:31-12:54
41
47.50
14:25-14:54
36
47.50
12:31-12:54
41
45.00
12:55-13:12
40
45.00
14:55-15:18
35
45.00
12:55-13:12
40
43.50
13:13-14:00
38-39
43.50
15:19-16:24
33-34
43.50
13:13-13:36
39
42.00
14:01-14:54
36-37
42.00
16:25-16:54
32
42.00
13:37-14:24
37-38
40.50
14:55-15:48
34-35
40.50
16:55-17:36
31
40.50
14:25-14:54
36
39.00
15:49-16:24
33
39.00
17:37-18:12
30
39.00
14:55-15:18
35
37.50
16:25-16:54
32
37.50
18:13-18:54
29
37.50
15:19-15:48
34
36.00
16:55-17:36
31
36.00
18:55-19:42
28
36.00
15:49-16:24
33
34.00
17:37-18:12
30
34.00
19:43-20:36
27
34.00
16:25-16:54
32
32.00
18:13-18:54
29
32.00
20:37-21:30
26
32.00
16:55-17:36
31
30.00
18:55-19:42
28
30.00
21:31-22:30
25
30.00
17:37-18:12
30
27.00
19:43-20:36
27
27.00
22:31-23:36
24
27.00
18:13-18:54
29
24.00
20:37-21:30
26
24.00
23:37-24:48
23
24.00
18:55-19:42
28
21.00
21:31-22:30
25
21.00
24:49-26:06
22
21.00
19:43-20:36
27
18.00
22:31-23:36
24
18.00
26:07-27:36
21
18.00
20:37-21:30
26
15.00
23:37-24:48
23
15.00
27:37-29:18
20
15.00
21:31-22:30
25
12.00
24:49-26:06
22
12.00
29:19-31:12
19
12.00
22:31-23:36
24
9.00
26:07-27:36
21
9.00
31:13-33:18
18
9.00
23:37-24:48
23
6.00
27:37-29:18
20
6.00
33:19-35:48
17
6.00
24:49-26:06
22
3.00
29:19-31:12
19
3.00
35:49-38:36
16
3.00
>26:06
<22
0.00
>31:12
<19
0.00
>38:36
<16
0.00
Figure 12
Cybex 750T Treadmill Owner’s Manual
Navy < 5K (FT4)
Program Overview
This program was designed by the Navy to test, evaluate and measure fitness levels. The goal is to
complete the set distance of 1.5 miles (2.4 km) in the least amount of time. The user controls the speed
as needed to reach the goal. A point value will be given at the completion of the test. See Figures 13 and
14.
NOTE: Use this program when performing the test at altitudes below 5,000 feet (1,524 meters).
Input information:
Age
Weight
Gender
Starting Speed
Test Result:
FT4 – �NAVY <5K PRT SCORE = XXX’
NAVY <5K
1.5 Mile Run Under 5000 Feet
MALES
Category
17-19
Level
Outstanding
High
Outstanding
Medium
Outstanding
Low
Excellent
High
Excellent
Medium
Excellent
Low
Good
High
Good
Medium
Good
Low
Satisfactory
High
Satisfactory
Medium
Probationary
35-39
40-44
20-24
25-29
30-34
Component 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run
Points
Time (min.) Time (min.) Time (min.) Time (min.)
100
95
90
85
80
75
70
65
60
55
50
45
8:15
8:45
9:00
9:15
9:30
9:45
10:00
10:30
11:00
12:00
12:15
12:30
8:30
9:00
9:15
9:45
10:00
10:30
10:45
11:30
12:00
12:45
13:15
13:30
45-49
50-54
55-59
8:55
9:23
9:38
9:20
9:45
10:00
10:15
10:30
10:52
10:30
11:00
11:15
11:23
12:15
12:53
12:00
13:00
13:45
13:23
13:45
14:00
14:00
14:15
14:30
60-64
65+
1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run
Time (min.) Time (min.) Time (min.) Time (min.) Time (min.) Time (min.) Time (min.)
9:25
9:53
10:08
9:30
10:00
10:15
9:33
10:08
10:30
9:35
10:15
10:45
10:42
11:09
11:25
11:21
11:48
12:04
11:41
12:13
12:43
10:38
11:08
11:23
10:45
11:15
11:45
11:08
11:38
12:08
11:30
12:00
12:30
11:57
12:29
13:12
12:40
13:16
13:53
13:20
13:57
14:34
12:23
13:23
14:08
12:45
13:45
14:30
13:00
14:08
14:53
13:15
14:30
15:15
14:13
15:14
16:15
15:00
16:07
17:14
15:47
17:00
18:13
14:23
14:45
15:00
14:45
15:15
15:30
15:15
15:45
16:08
15:45
16:15
16:45
16:33
16:51
17:09
17:47
18:20
18:52
19:00
19:47
20:35
Figure 13
Program
Overviews
Page B-15
Cybex 750T Treadmill Owner’s Manual
Navy (FT4) continued
FEMALES
17-19
Category
Level
Outstanding
High
Outstanding
Medium
Outstanding
Low
Excellent
High
Excellent
Medium
Excellent
Low
Good
High
Good
Medium
Good
Low
Satisfactory
High
Satisfactory
Medium
Probationary
35-39
40-44
20-24
25-29
30-34
Component 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run
Points
Time (min.) Time (min.) Time (min.) Time (min.)
100
95
90
85
80
75
70
65
60
55
50
45
9:29
11:15
11:30
11:45
12:00
12:30
12:45
13:00
13:30
14:15
14:45
15:00
9:47
11:15
11:30
10:17
11:30
11:45
10:46
11:45
12:00
12:15
12:45
13:15
12:30
13:00
13:23
12:45
13:15
13:30
13:30
13:45
14:15
14:00
14:30
14:53
14:30
15:15
15:30
15:00
15:15
15:30
15:23
15:45
16:08
15:45
16:15
16:45
45-49
50-54
55-59
60-64
65+
1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run
Time (min.) Time (min.) Time (min.) Time (min.) Time (min.) Time (min.) Time (min.)
10:51
11:53
12:08
10:56
12:00
12:15
10:58
12:08
12:30
11:00
12:15
12:45
12:23
13:39
13:57
13:34
14:50
15:08
14:45
16:01
16:19
12:53
13:23
13:45
13:00
13:30
14:00
13:15
13:45
14:08
13:30
14:00
14:15
14:25
14:53
15:20
15:34
16:00
16:25
16:43
17:07
17:30
14:38
15:30
15:53
14:45
15:45
16:15
15:00
15:53
16:30
15:15
16:00
16:45
16:09
16:58
17:48
17:17
18:06
18:51
18:18
19:06
19:54
16:15
16:38
17:00
16:45
17:00
17:15
16:53
17:08
17:23
17:00
17:15
17:30
18:03
18:18
18:34
19:08
19:25
19:43
20:13
20:31
20:52
Figure 14
Program
Overviews
Page B-16
Cybex 750T Treadmill Owner’s Manual
Navy > 5K (FT5)
Program Overview
This program was designed by the Navy to test, evaluate and measure fitness levels. The goal is to
complete the set distance of 1.5 miles (2.4 km) in the least amount of time. The user controls the speed
as needed to reach the goal. A point value will be given at the completion of the test. See Figures 15 and
16.
NOTE: Use this program when performing the test at altitudes above 5,000 feet (1,524 meters).
Input information:
Age
Weight
Gender
Starting Speed
Test Result:
FT5 – �NAVY >5K PRT SCORE = XXX’
NAVY >5K
1.5 Mile Run Over 5000Feet
MALES
Category
17-19
Level
Outstanding
High
Outstanding
Medium
Outstanding
Low
Excellent
High
Excellent
Medium
Excellent
Low
Good
High
Good
Medium
Good
Low
Satisfactory
High
Satisfactory
Medium
Probationary
35-39
40-44
Component
Points
100
95
90
85
80
75
70
65
60
55
50
45
45-49
20-24
25-29
30-34
1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run
Time (min.) Time (min.) Time (min.) Time (min.)
9:00
9:30
9:50
10:05
10:20
10:40
10:55
11:25
12:00
13:05
13:20
13:40
50-54
9:15
9:50
10:05
10:40
10:55
11:25
11:45
12:30
13:05
13:55
14:25
14:45
55-59
9:43
10:15
10:30
10:10
10:40
10:55
11:13
11:28
11:50
11:45
12:00
12:15
12:25
13:20
14:03
13:05
14:10
15:00
14:35
14:58
15:18
15:15
15:30
15:50
60-64
65+
1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run
Time (min.) Time (min.) Time (min.) Time (min.) Time (min.) Time (min.) Time (min.)
10:15
10:48
11:03
10:20
10:55
11:10
10:23
11:03
11:28
10:25
11:10
11:45
11:46
12:16
12:34
12:29
12:59
13:16
12:51
13:26
13:59
11:45
12:08
12:33
11:45
12:15
12:50
12:08
12:40
13:15
12:30
13:05
13:40
13:09
13:44
14:31
13:56
14:36
15:16
14:40
15:21
16:01
13:30
14:35
15:25
13:55
15:00
15:50
14:10
15:25
16:15
14:25
15:50
16:40
15:38
16:45
17:53
16:30
17:44
18:57
17:22
18:42
20:02
15:40
16:05
16:23
16:05
16:40
16:55
16:38
17:13
17:35
17:10
17:45
18:15
18:12
18:32
18:52
19:34
20:10
20:45
20:54
21:46
22:39
Figure 15
Program
Overviews
Page B-17
Cybex 750T Treadmill Owner’s Manual
Navy (FT5) continued
FEMALES
Category
17-19
Level
Outstanding
High
Outstanding
Medium
Outstanding
Low
Excellent
High
Excellent
Medium
Excellent
Low
Good
High
Good
Medium
Good
Low
Satisfactory
High
Satisfactory
Medium
Probationary
35-39
40-44
Component
Points
100
95
90
85
80
75
70
65
60
55
50
45
45-49
20-24
25-29
30-34
1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run
Time (min.) Time (min.) Time (min.) Time (min.)
10:20
12:15
12:30
12:50
13:05
13:40
13:55
14:10
14:45
15:30
16:05
16:20
50-54
10:40
12:15
12:30
11:13
12:33
12:48
11:45
12:50
13:05
13:20
13:55
14:25
13:38
14:10
14:35
13:55
14:25
14:45
14:45
15:00
15:30
15:18
15:50
16:13
15:50
16:40
16:55
16:20
16:40
16:55
16:45
17:13
17:35
17:10
17:45
18:15
55-59
60-64
65+
1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run 1.5-Mile Run
Time (min.) Time (min.) Time (min.) Time (min.) Time (min.) Time (min.) Time (min.)
11:50
12:58
13:13
11:55
13:05
13:20
11:58
13:13
13:38
12:00
13:20
13:55
13:37
15:01
15:21
14:55
16:19
16:39
16:14
17:37
17:57
14:03
14:35
15:00
14:10
14:45
15:15
14:28
15:00
15:23
14:45
15:15
15:30
15:52
16:22
16:52
17:07
17:36
18:04
18:23
18:50
19:15
15:58
16:55
17:20
16:05
17:10
17:45
16:23
17:18
18:00
16:40
17:25
18:15
17:46
18:40
19:35
19:01
19:55
20:44
20:08
21:01
21:53
17:43
18:08
18:33
18:15
18:30
18:50
18:23
18:40
18:58
18:30
18:50
19:05
19:51
20:08
20:25
21:03
21:22
21:41
22:14
22:34
22:57
Figure 16
Program
Overviews
Page B-18
Cybex 750T Treadmill Owner’s Manual
Marines Sea Level (FT6)
Program Overview
This program was designed by the Marines to test, evaluate and measure fitness levels. The goal is to
complete the set distance of 3.0 miles (4.8 km) in the least amount of time. The user controls the speed
as needed to reach the goal. A point value will be given at the
completion of the test. See Figure 17.
NOTE: Use this program when performing the test at altitudes below 4,500 feet (1,372 meters).
Input information:
Age
Weight
Gender
Starting Speed
Test Result:
FT6 – �MARINES SEA-LEVEL PRT SCORE = XXX’
Required minimum scores (Male)
MARINES SEA LEVEL
3-Mile Run Points
Points
Male
Female
3 mile run no 3 mile run no
altitude
altitude
100
18:00
21:00
90
19:40
22:40
80
21:20
24:20
70
23:00
26:00
60
24:40
27:40
50
26:20
29:20
40
28:00
31:00
30
29:40
32:40
20
31:20
34:20
10
33:00
36:00
Age
Unsatisfactory
3rd Class
2nd Class
1st Class
17-26
0-134
135
175
225
27-39
0-109
110
150
200
40-45
0-87
88
125
175
46+
0-64
65
100
150
Required minimum scores (Female)
Age
Unsatisfactory
3rd Class
2nd Class
1st Class
17-26
0-134
135
175
225
27-39
0-109
110
150
200
40-45
0-87
88
125
175
46+
0-64
65
100
150
Figure 17
Program
Overviews
Page B-19
Cybex 750T Treadmill Owner’s Manual
Marines > 4.5K (FT7)
Program Overview
This program was designed by the Marines to test, evaluate and measure fitness levels. The goal is to
complete the set distance of 3.0 miles (4.8 km) in the least amount of time. The user controls the speed
as needed to reach the goal. A point value will be given at the completion of the test. See Figure 18.
NOTE: Use this program when performing the test at altitudes above 4,500 feet (1,372 meters).
Input information:
Age
Weight
Gender
Starting Speed
Test Result:
FT7 – �MARINES >4.5K PRT SCORE = XXX’
MARINES > 4.5K
3-Mile Run Points
Points
Male
3 mile run
4,500 feet
above sea
level
Female
3 mile run
4,500 feet
above sea
level
100
19:30
22:30
90
21:10
24:10:00
Age
Unsatisfactory
3rd Class
2nd Class
1st Class
17-26
0-134
135
175
225
27-39
0-109
110
150
200
40-45
0-87
88
125
175
46+
0-64
65
100
150
80
22:50
25:50:00
70
24:30:00
27:30:00
60
26:10:00
29:10:00
Age
Unsatisfactory
3rd Class
2nd Class
1st Class
50
27:50:00
30:50:00
17-26
0-134
135
175
225
40
29:30:00
32:30:00
27-39
0-109
110
150
200
34:10:00
40-45
0-87
88
125
175
35:50:00
46+
0-64
65
100
150
30
31:10:00
20
32:50:00
10
34:30:00
37:30:00
1
36:00:00
39:00:00
Figure 18
Program
Overviews
Page B-20
Required minimum scores (Male)
Required minimum scores (Female)
Cybex 750T Treadmill Owner’s Manual
One Mile (FT8)
Program Overview
The objective of this test is to monitor the development of the athlete’s VO2 max. See Figure 19.
(continued on next page)
Input information:
Age
Weight
Gender
Starting Speed
Heart rate
Heart Rate Requirements:
Wireless heart rate transmitter
Test procedure:
1. Record your weight
2. Walk one mile (1,609 metres) as fast as possible
3. Record the time to complete the one mile walk
4. Immediately on finishing the walk record your heart rate (beats per minute)
5. Determine your VO2 max
The formula used to calculate VO2 max is:
132.853 - (0.0769 * Weight) - (0.3877 * Age) + (6.315 * Gender) - (3.2649 * Time) - (0.1565 * Heart rate)
Input values are:
Weight is in pounds (lbs)
Age is in years
Gender Male = 1 and Female = 0
Time is expressed in minutes and 100ths of minutes
Heart rate is in beats/min
Test Result:
FT8 – �ONE MILE TEST PREDICTED VO2 MAX = XXX’
Program
Overviews
Page B-21
Cybex 750T Treadmill Owner’s Manual
One Mile (FT8) continued
Analyses of VO2 max scores
Female (values in ml/kg/min)
Age
Very Poor
Poor
Fair
Good
Excellent
Superior
13-19
<25.0
25.0 - 30.9
31.0 - 34.9
35.0 - 38.9
39.0 - 41.9
>41.9
20-29
<23.6
23.6 - 28.9
29.0 - 32.9
33.0 - 36.9
37.0 - 41.0
>41.0
30-39
<22.8
22.8 - 26.9
27.0 - 31.4
31.5 - 35.6
35.7 - 40.0
>40.0
40-49
<21.0
21.0 - 24.4
24.5 - 28.9
29.0 - 32.8
32.9 - 36.9
>36.9
50-59
<20.2
20.2 - 22.7
22.8 - 26.9
27.0 - 31.4
31.5 - 35.7
>35.7
60+
<17.5
17.5 - 20.1
20.2 - 24.4
24.5 - 30.2
30.3 - 31.4
>31.4
Male (values in ml/kg/min)
Age
Very Poor
Poor
Fair
Good
Excellent
Superior
13-19
<35.0
35.0 - 38.3
38.4 - 45.1
45.2 - 50.9
51.0 - 55.9
>55.9
20-29
<33.0
33.0 - 36.4
36.5 - 42.4
42.5 - 46.4
46.5 - 52.4
>52.4
30-39
<31.5
31.5 - 35.4
35.5 - 40.9
41.0 - 44.9
45.0 - 49.4
>49.4
40-49
<30.2
30.2 - 33.5
33.6 - 38.9
39.0 - 43.7
43.8 - 48.0
>48.0
50-59
<26.1
26.1 - 30.9
31.0 - 35.7
35.8 - 40.9
41.0 - 45.3
>45.3
60+
<20.5
20.5 - 26.0
26.1 - 32.2
32.3 - 36.4
36.5 - 44.2
>44.2
Figure 19
Program
Overviews
Page B-22
Cybex 750T Treadmill Owner’s Manual
Parts List
ITEM QTY.
PART NO.
DESCRIPTION
ITEM QTY.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
15
16
17
18
19
20
21
23
24
25
2
2
2
1
1
2
1
1
1
1
1
1
1
1
2
2
2
1
1
4
2
1
AF-19988
AF-20052
AF-20206
AL-19740
AL-19741
AX-20035
AX-20094
AX-20383
AX-20452
AX-20453
BD-19889
BD-20049
DE-14486
DE-18413
DE-19360
DE-20392
DE-20393
DE-20427
DK-20024
EH-10291
FM-20096
FM-20099
56
57
58
59
60
2
4
7
2
2
HW-20089
HW-53017
HX-13771
HX-19102
HX-19991
62
63
64
65
1
1
1
1
PL-20262
PL-20263
PL-20264
PL-20265
66
1
PL-20266
67
1
PL-20269
68
1
PL-20270
69
70
74
2
2
2
HS-41107
HW-00165
EH-20254
26
4
FS-16511
27
2
FS-20031
28
29
1
1
FS-20109
FT-16825
75
76
77
81
82
83
84
85
1
2
1
1
1
1
1
1
HX-20248
EH-20244
DE-19198
AF-20842
HS-11976
HX-20843
HN-60064
HS-60022
30
1
FT-16826
86
87
1
2
CW-22240
HX-22247
31
32
33
34
35
36
37
38
39
2
2
2
4
2
2
2
4
17
HB-16367
HB-20097
HB-20098
HN-11136
HN-17935
HN-20041
HN-20693
HS-00700
HS-11977
89
2
HS-22137
90
2
PL-22129
91
92
5
1
EH-00986
DE-22327
92
1
DE-22328
40
41
42
12
2
9
HS-12295
HS-15480
HS-15706
101
1
MR-22239
102
1
AX-20235
43
8
HS-16509
102
1
AX-20236
44
8
HS-16929
102
1
AX-20237
45
4
HS-16939
103
1
MR-19992
46
47
48
49
51
52
53
54
55
1
1
2
8
12
2
2
14
2
HS-17936
HS-17937
HS-18358
HS-19108
HW-00180
HW-00590
HW-10028
HW-18123
HW-20044
NUT, ROLLER, REAR
BRACKET, MOTOR,MOUNTING
CLAMP, LOWER, TOP STEP
ROLLER ASSY, FRONT
ROLLER ASSY, REAR
ASSY, DECK PIVOT BRACKET
ASSY, ELEVATION
ASSY, MOTOR COVER
ASSY, END CAP, LEFT
ASSY, END CAP, RIGHT
BELT, RUNNING, 21.88 X 61.75”
BELT, DRIVE
DECAL SERIAL NUMBER
DECAL, ETL AND CSA
DECAL, CYBEX, BLACK
DECAL, 750T, BLACK
DECAL, 750T, SILVER
DECAL, DISCONNECT POWER
DECK, RUNNING, 29.00 X 53.5”
TY WRAP BASE
PIN, ELEVATION PIVOT
MOUNTING SHAFT, ELEVATION
MOTOR
PLATE, REAR RUBBER FOOT
MOUNT
PLATE, RETAINER, UPPER, TOP
STEP
SHIELD, SPLASH
SLEEVE, ELEVATION MOUNTING,
TOP
SLEEVE, ELEVATION MOUNTING,
BOTTOM
BUSHING .50 ID X .62 OD X .31”
BEARING, FLANGE, BRONZE
BEARING, THRUST, BRONZE
KEPS 5/16” HEX STL ZINC
NUT LOCK, 3/8 - 24
NUT, 1/4 - 20 PROPELLER
NUT, TEE, 5/16 - 18, 1-2” BARREL
SCREW, 8-32 X 0.50”, PNHD PHIL
SCREW SEMS, 8-32 X .38, PNHD
PHIL
BOLT, 1/4 - 20 X 1.75”, HXHD, G5
BOLT TAP, 1/2 - 13 X 6, HXHD, G5
SCREW, 8-16 X .50”, PNHD, STL,
BLK ZN
SCREW SLFTP, 10 X .5”, PNHD,
PLT, TYP
BOLT WHIZ LOCK, 3/8 - 16 X .625”,
HXHD
SCREW SEMS, 10-32 X .75, PNHD,
BLK
BOLT, 3/8 - 24 X 2.0”, HXHD CAP
BOLT, 3/8 - 24 X 2.75”, HXHD CAP
BOLT, 5/16 - 18 X .1.25”, SCHD CAP
SCREW 5/16 - 18 X 3/4”, HXHD
WASHER, SPLIT LOCK 1/4”, SST
BUSHING, NYLON, 1/2”
WASHER, 1/2”
WASHER, .344 ID X .75 OD X .125”
WASHER, BELLEVILLE, 15 X 8.2 X
1.0 mm
103
1
MR-19993
111
111
111
1
1
1
KAD-22221
KAD-22431
KAD-22223
112
113
114
115
1
1
1
1
AD-21879
AF-20123
AF-20234
AW-19404
WASHER, WAVE, .650 ID X .855”
WASHER FLAT, 5/16”, SS
RING, RETAINING, 5/8” 0.579 ID
FOOT, RUBBER, REAR
BUMPER, SPRING DECK, 2.10 X
2.34 X 1”
COVER, LEFT SIDE FRONT
COVER, RIGHT SIDE FRONT
COVER, FRONT
COVER, REAR, FRAME OUTER,
LEFT
COVER, REAR, FRAME INNER,
LEFT
COVER, REAR, FRAME OUTER,
RIGHT
COVER, REAR, FRAME INNER,
RIGHT
BOLT, 5/16 - 18 X 1.5”, BTHD, SST
WASHER, SPLIT LOCK 5/16”
CLIP,WIRE RETAINER,.24-.47”,
DIA,.105THK
GROMMET,RUBBER,1.12”DIA
CLIP, WIRE RETAINER, .24-.47”DIA
DECAL,CYBEX
BRACKET, MOTOR COVER
SCREW, SEMS, 10-32 X .38”
BUMPER, MOTOR COVER
NUT, JAM, 3/8 - 16”, BLACK ZN
BOLT, 3/8 X 2.25”, HXHD, CAP,
BLK
WHEEL,80MM DIA X 32MM W
BUSHING,SPANNER,.500 OD X
1.5”L
BOLT, 1/4-14 x 1.25”,HXHD
WSHR,TYP
BRACKET,POWER CORD
STORAGE,PLASTIC
TY WRAP 9”
LABEL,BLACK,INTELLIGENT
SUSPENSION 3
LABEL,SILVER,INTELLIGENT
SUSPENSION 3
ASSY, MOTOR, TREADMILL, AC
DRIVE
SUB ASSY, 110 VAC
CONTROLLER
SUB ASSY, 220 VAC
CONTROLLER
SUB ASSY, 230 VAC, 50HZ
CONTROLLER
MOTOR, ELEVATION, 115 VAC,
60 HZ
MOTOR, ELEVATION, 230 VAC,
50-60 HZ
PCA, CNTRL, GOLD, 115 VAC
PCA, CNTRL, TIN, 230 VAC
PCA, CNTRL, GOLD, 230 VAC,
50 HZ
PCA, HUB BOARD
PLATE, SWITCHES
BRACKET,CONTROLLER, PCB
CABLE, CAT5, RJ45 FLAT PATCH
12”
Parts List
Page C-1
Cybex 750T Treadmill Owner’s Manual
ITEM QTY. PART NO.
DESCRIPTION
ITEM QTY. PART NO.
DESCRIPTION
116
1
AW-20289
323
4
HS-41006
117
1
AW-20290
324
15
HS-41187
118
1
AW-20291
325
2
HX-20360
119
120
1
1
AW-22177
AW-20442
326
328
329
1
1
1
PL-20143
PL-20210
PL-20211
121
1
AW-20443
122
1
AW-20444
330
331
1
1
PL-20218
PL-20274
123
1
AW-20446
332
1
PL-20275
124
1
AW-20447
333
334
1
1
PL-20340
PL-20355
125
126
127
128
130
1
1
1
1
1
CN-20252
DE-20558
EC-18896
EH-12208
FS-20232
335
1
PL-20356
336
1
PL-20357
131
132
134
2
2
4
HN-11925
HS-10405
HS-15732
337
338
345
346
347
1
1
1
1
4
PL-20550
SW-21183-X*
PL-20549-X*
AX-20513
HS-20553
135
1
HW-10856
136
1
RE-20242
137
1
SW-19666
137
1
SW-19667
200
201
202
203
204
205
300
1
1
1
1
1
2
1
AF-19890
AF-19921
AF-19922
AX-20331
AX-20332
DE-20305
AC-21401-X*
350
351
352
352
353
354
355
356
357
358
359
360
362
363
364
1
2
1
1
1
1
1
1
6
2
2
2
1
1
1
DE-20735-X*
KHX-21337
DE-21596
SW-20813-X*
KAD-21926
AF-21482
KAF-21910
AX-21798-X*
HN-21072
HS-11347
HS-12083
HS-13739
PL-21792
PL-21793
PL-21794
302
303
304
305
306
307
309
311
312
1
1
1
1
1
1
1
1
1
AF-21761
AW-19694
AW-20170
AW-20239
AX-19936
AX-19941
AX-20552
DE-20364
DE-21184
365
1
KAW-20820
400
401
403
404
1
1
1
1
AD-21736
AF-20137
AW-21489
AW-20241
406
1
AW-21499
312
1
DE-21184-4
408
1
CP-21072
313
314
315
1
1
4
EC-19706
EC-19974
HN-20362
409
416
418
1
1
1
FS-20300
PL-20278
TR-21881
316
317
319
321
2
4
8
2
HS-10716
HS-14391
HS-18320
HS-20367
419
1
FS-20233
422
1
CP-21073
322
3
WIRE, INLET TO SWITCH FILTER
JUMPER
WIRE, SWITCH TO FILTER
JUMPER
WIRE, INLET TO GROUND
JUMPER, GREEN
CABLE, MOTOR CONTROLLER
WIRE, FILTER TO OUTLET
JUMPER, BLACK
WIRE, FILTER TO OUTLET
JUMPER, WHITE
WIRE, OUTLET, GROUND JUMPER,
GREEN
WIRE, INLET TO SWITCH JUMPER,
BLACK
WIRE, INLET TO SWITCH JUMPER,
WHITE
PLUG, NEMA 5-15R
LABEL, HUB BOARD
FILTER, 16A
INLET, IEC, 320 16-20 AMP
BRACKET, POWER CORD
RETAINER
KEPS, 10-32, HEX, STL, ZN
SCREW, 4-40 X .25”,PNHD PHIL
SCREW, SEMS, 8-32 UNC X .62”,
PNHD, PHIL
WASHER, LOCK, EXTERNAL, NO.
10
RESISTOR, TM5, DYNAMIC
BRAKE
SWITCH, CIRCUIT BREAKER, 15
AMP, 240 VAC
SWITCH, CIRCUIT BREAKER, 20
AMP, 240 VAC
WELDMENT, FRAME
WELDMENT, UPRIGHT, LEFT
WELDMENT, UPRIGHT, RIGHT
ASSY, TOP PLATFORM, LEFT
ASSY, TOP PLATFORM, RIGHT
DECAL, SAFETY WALK
ASSY, CONSOLE, 751T, AMBER
LED
WELDMENT, CONSOLE
CABLE, HANDSET TO DISPLAY
CABLE, MOTION SENSOR
CABLE, 750T CONSOLE
ASSY, HANDRAIL, LEFT
ASSY, HANDRAIL, RIGHT
ASSY, E-STOP KEY
DIFFUSER, DISC, 0.6” OD
DECAL, 751T, CONSOLE, TOP,
AMBER LED, LANGUAGES
DECAL, 751T, CONSOLE, TOP,
AMBER LED, ENGLISH
FAN, 12 VDC, 120 X 120MM
SENSOR, IR MOTION
NUT, SELF THREADING, 3/8 X
11/16”, ST
SCREW, 4-40 X 0.38”, PNHD, PHIL
SCREW, 6-32 X .38, PNHD, PHIL
SCREW, 6-19 X 1-2”, PNHD, PHIL
SCREW, SEMS, M4 X 10 mm,
PNHD, PHIL
SCREW, SEMS, 8-32 X 1.25”,
PNHD, PHIL
423
1
PL-21178
SCREW, SLFTP, 10-24 X .5,
PNHD, PHIL
SCREW, SLFTP, 8-16 X .3125”,
PLASTITE
INSERT, EXPANSION, PLASTIC,
#8 - #1
HOUSING, E-STOP
CONSOLE, BACK PANEL
CONSOLE, JUNCTION COVER,
INNER, LEFT
DUCT, FAN, RIGHT
ISOLATOR, WATER, BOTTLE,
LEFT
ISOLATOR, WATER, BOTTLE,
RIGHT
DUCT, FAN, LEFT
COVER, JUNCTION, CONSOLE,
OUTER, LEFT
COVER, JUNCTION, CONSOLE,
INNER, RIGHT
COVER, JUNCTION, CONSOLE,
OUTER, RIGHT
CONSOLE, FRONT
MEMBRANE, 750T, KEYBOARD
BUTTON, STOP, MOLDED
SWITCH, BUTTON, STOP
SCREW, 4 X 3/8”, SLFTP, PNHD,
PHIL, ZN, PLASTITE
LABEL, WARNING, CONSOLE
BOTTLE STABILIZER
LABEL, AV BLANK, 750T
MEMBRANE,AV KEYPAD
PCA,PEM JACK BOARD
BRACKET,AV,LOWER,750T
WELDMENT,AV,750T
ASSY,HANDSET,TOP W-TABS
PEM MOUNTING NUT
BOLT,1-4-20X0.75,SCHD BTN,BLK
BOLT LCK,1-4-20X.625
BOLT LCK,1-4-20X1.25,G5
COVER,HANDSET BOTTOM
COVER,HANDSET AV MODULE
COVER,HANDSET NON AV
MODULE
KIT,C-HR REPLACEMENT
CONTACT GRIPS WITH
CONNECTOR WIRES
PCA, HANDSET, UNIVERSAL
BRACKET, A/V POWER SUPPLY
CABLE,CAT5E 24” PATCH,BLUE
POWER CORD, IEC NEMA 5-15,
SHORT FOR A/V
CABLE,LOCKING RF and DC
POWER CABLE,2795MM
MONITOR,13.3”, ATSC, NTSC,
PEM
STRAP, A/V POWER SUPPLY
CONSOLE TOP W/O A/V
POWER SUPPLY,12V FAN
LOCKING DC
BRACKET, FAN POWER SUPPLY
RETAINER
MONITOR,13.3”, DVB-T, SECAM,
PAL, PEM
CONSOLE, TOP, A/V, 751T
Parts List
Page C-2
HS-20399
Cybex 750T Treadmill Owner’s Manual
ITEM QTY. PART NO.
424
1
434
1
435
436
500
500
501
502
503
1
1
2
2
2
4
9
504
2
551
1
554
554
555
1
1
1
NS
NS
NS
NS
1
1
1
1
NS
1
NS
1
NS
NS
1
1
NS
NS
NS
NS
1
1
1
1
DESCRIPTION
HS-11894
SCREW SEMS, 6/32 X .25”, PNHD
PHIL
AW-20892
CABLE, COMP AV JACK BOARD,
GREEN
AW-20841
CABLE,IPOD
DE-22190
LABEL,NIKE+ IPOD
HS-00293
BOLT, 5/16 - 18 X 2.0”, HXHD
HS-41050
BOLT, 5/16-18 x 2.25”, HXHD, G5
HW-00189
WASHER, FLAT, 5/16”
HN-42063
NUT, 5/16-18, FLANGED, SS BO
HS-18311
SCREW, 8-16 X .75”, PNHD PHIL,
STL
HS-20361
SCREW, SLFTP, 8-16 X 2.5”,
PLASTITE
KAX-22598-X* KIT,751T SPLIT DISPLAY W
ENUNCIATOR
AD-22403
PCA,751T SPLIT DISPLAY MCC
AD-22509
PCA,751T SPLIT DISPLAY IFI MCC
AW-21281
CABLE, DISPLAY UPPER TO
LOWER
AW-20280
POWER CORD, 115 VAC, 20A, 60HZ
AW-20281
POWER CORD, 220 VAC, 15A, 60HZ
AW-20282
POWER CORD, 230 VAC, 16A, 50HZ
AW-20283
POWER CORD, UK, 230 VAC, 13A,
50HZ
AW-22228
POWER CORD, DANISH, 230 VAC,
13A, 50HZ, IEC320
AW-21882
CABLE,ADAPTER,LOCKING DC
2.1mm
AX-20454
KIT, INSTALL HARDWARE
KMR-20818 KIT,FAN REPLACEMENT,PCB
MOTOR CONTROLLER
LT-03051
SIGN, FACILITY SAFETY
LT-20404
POSTER, INSTALL
LT-20405
WARRANTY SHEET
LT-20406-X* OWNER’S MANUAL, 750T/751T
NOTE: NS = Not Shown
*Language Key
1-German
2-French
3-Spanish
4-English
6-Japanese
7-Swedish
8-Russian
A-Danish
Parts List
Page C-3
Cybex 750T Treadmill Owner’s Manual
This page intentionally left blank
Parts List
Page C-4
Cybex 750T Treadmill Owner’s Manual
Appendix D – Exploded Views
ITEM QTY. PART NO.
DESCRIPTION
ITEM QTY. PART NO.
DESCRIPTION
1
3
4
5
6
11
12
21
25
2
2
1
1
2
1
1
1
1
AF-19988
AF-20206
AL-19740
AL-19741
AX-20035
BD-19889
BD-20049
DK-20024
FM-20099
47
1
HS-17937
48
2
HS-18358
49
51
52
53
54
8
12
2
2
14
HS-19108
HW-00180
HW-00590
HW-10028
HW-18123
27
2
FS-20031
55
2
HW-20044
31
36
40
41
44
2
2
12
2
8
HB-16367
HN-20041
HS-12295
HS-15480
HS-16929
NUT, ROLLER, REAR
CLAMP, LOWER, TOP STEP
ROLLER ASSY, FRONT
ROLLER ASSY, REAR
ASSY, DECK PIVOT BRACKET
BELT, RUNNING, 21.88 X 61.75”
BELT, DRIVE
DECK, RUNNING, 29.00 X 53.5”
MOUNTING SHAFT, ELEVATION
MOTOR
PLATE, RETAINER, UPPER, TOP
STEP
BUSHING .50 ID X .62 OD X .31”
NUT, 1/4 - 20 PROPELLER
BOLT, 1/4 - 20 X 1.75”, HXHD, G5
BOLT TAP, 1/2 - 13 X 6, HXHD
BOLT WHIZ LOCK, 3/8 - 16 X
.625”, HXHD
56
58
60
2
7
2
HW-20089
HX-13771
HX-19991
BOLT, 3/8 - 24 X 2.75”,
HXHD CAP
BOLT, 5/16 - 18 X .1.25”,
SCHD CAP
SCREW 5/16 - 18 X 3/4”, HXHD
WASHER, SPLIT LOCK 1/4”
BUSHING, NYLON, 1/2”
WASHER, 1/2”
WASHER, .344 ID X .75 OD X
.125”
WASHER, BELLEVILLE, 15 X
8.2 X 1.0 mm
WASHER, WAVE, .650 ID X .855”
RING, RETAINING, 5/8” 0.579 ID
BUMPER, SPRING DECK, 2.10
X 2.34 X 1”
751T Belt, Deck and Rollers
44
12
4
44
54
51
40
11
27
3
5
21
48
6
55
36
58
56
58
49
60
25
6
1
58
1
31
52
53
41
49
Exploded
Views
Page D-1
Cybex 750T Treadmill Owner’s Manual
ITEM QTY. PART NO.
42
9 HS-15706
49
302
303
304
305
306
307
309
311
312
8
1
1
1
1
1
1
1
1
1
HS-19108
AF-21761
AW-19694
AW-20170
AW-20239
AX-19936
AX-19941
AX-20552
DE-20364
DE-21184
312
1
DE-21184-4
313
314
315
1
1
4
EC-19706
EC-19974
HN-20362
316
2
HS-10716
317
319
321
4
8
2
HS-14391
HS-18320
HS-20367
322
3
HS-20399
323
4
HS-41006
324
15
HS-41187
325
2
HX-20360
326
328
329
1
1
1
PL-20143
PL-20210
PL-20211
DESCRIPTION
SCREW, 8-16 X .50”, PNHD, STL,
BLK ZN
SCREW 5/16 - 18 X 3/4”, HXHD
WELDMENT, CONSOLE
CABLE, HANDSET TO DISPLAY
CABLE, MOTION SENSOR
CABLE, 750T CONSOLE
ASSY, HANDRAIL, LEFT
ASSY, HANDRAIL, RIGHT
ASSY, E-STOP KEY
DIFFUSER, DISC, 0.6” OD
DECAL, 751T, CONSOLE, TOP,
AMBER LED, LANGUAGES
DECAL, 751T, CONSOLE, TOP,
AMBER LED, ENGLISH
FAN, 12 VDC, 120 X 120MM
SENSOR, IR MOTION
NUT, SELF THREADING, 3/8 X
11/16”, ST
SCREW, 4-40 X 0.38”, PNHD,
PHIL
SCREW, 6-32 X .38, PNHD, PHIL
SCREW, 6-19 X 1-2”, PNHD, PHIL
SCREW, SEMS, M4 X 10 mm,
PNHD, PHIL
SCREW, SEMS, 8-32 X 1.25”,
PNHD, PHIL
SCREW, SLFTP, 10-24 X .5,
PNHD, PHIL
SCREW, SLFTP, 8-16 X .3125”,
PLASTITE
INSERT, EXPANSION, PLASTIC,
#8 - #1
HOUSING, E-STOP
CONSOLE, BACK PANEL
CONSOLE, JUNCTION COVER,
INNER, LEFT
ITEM QTY.
330
1
331
1
332
1
333
1
334
1
PART NO.
PL-20218
PL-20274
PL-20275
PL-20340
PL-20355
335
1
PL-20356
336
1
PL-20357
337
338
345
346
347
1
1
1
1
4
PL-20550
SW-21183-X*
PL-20549-X*
AX-20513
HS-20553
350
351
352
352
356
362
364
365
1
2
1
1
1
1
1
1
DE-20735-X*
KHX-21337
DE-21596
SW-20813-X*
AX-21798-X
PL-21792
PL-21794
KAW-20820
400
416
503
1
1
9
AD-21736
PL-20278
HS-18311
504
2
HS-20361
551
1
KAX-22598-4
554
554
555
1
1
1
AD-22403
AD-22509
AW-21281
DESCRIPTION
DUCT, FAN, RIGHT
ISOLATOR, WATER, BOTTLE, LEFT
ISOLATOR, WATER, BOTTLE, RIGHT
DUCT, FAN, LEFT
COVER, JUNCTION, CONSOLE,
OUTER, LEFT
COVER, JUNCTION, CONSOLE,
INNER, RIGHT
COVER, JUNCTION, CONSOLE,
OUTER, RIGHT
CONSOLE, FRONT
MEMBRANE, 750T, KEYBOARD
BUTTON, STOP, MOLDED
SWITCH, BUTTON, STOP
SCREW, 4 X 3/8”, SLFTP, PNHD,
PHIL, ZN, PLASTITE
LABEL, WARNING, CONSOLE
BOTTLE STABILIZER
LABEL, AV BLANK, 750T
MEMBRANE,AV KEYPAD
ASSY,HANDSET,TOP W-TABS
COVER,HANDSET BOTTOM
COVER,HANDSET NON AV MODULE
KIT,C-HR REPLACEMENT CONTACT
GRIPS W-CONNECTOR WIRES
PCA, HANDSET, UNIVERSAL
CONSOLE TOP W/O A/V
SCREW, 8-16 X .75”, PNHD PHIL,
STL
SCREW, SLFTP, 8-16 X 2.5”,
PLASTITE
KIT,751T SPLIT DISPLAY W
ENUNCIATOR,ENG
PCA,751T SPLIT DISPLAY MCC
PCA,751T SPLIT DISPLAY IFI MCC
CABLE, DISPLAY UPPER TO
LOWER
*Language Key
1-German 2-French 3-Spanish 4-English 6-Japanese 7-Swedish 8-Russian A-Danish
751T Console
416
42
330 321 333
324
328
322
551
302
400 324
313
337
332
312
311
351
331
338
317
503
324
42
315
351
325
554
49
303
324
49
350
356
336
504
314
335
326
5.0” REF
352
316
304
329
345
362
334
346
365
307
319
364
365
AW-19694
Handset to Display Cable
AW-20170
Motion Sensor Cable
5.9” REF
309
305
347
AW-20239
Display Cable
B
A
323
319
63.0” REF
555
AW-21281
Upper to Lower Display Cable
306
Exploded
Views
Page D-2
3.0” REF
Cybex 750T Treadmill Owner’s Manual
ITEM QTY. PART NO.
DESCRIPTION
ITEM QTY. PART NO.
DESCRIPTION
42
9
HS-15706
314
316
1
2
EC-19974
HS-10716
319
324
8
15
HS-18320
HS-41187
358
359
360
362
363
400
403
404
2
2
2
1
1
1
1
1
HS-11347
HS-12083
HS-13739
PL-21792
PL-21793
AD-21736
AW-21489
AW-20241
326
345
346
347
1
1
1
4
PL-20143
PL-20549-X*
AX-20513
HS-20553
406
1
AW-21499
408
422
1
1
CP-21072
CP-21073
350
352
353
354
355
356
357
1
1
1
1
1
1
6
DE-20735-X*
SW-20813-X*
KAD-21926
AF-21482
KAF-21910
AX-21798-X*
HN-21072
SCREW, 8-16 X .50”, PNHD, STL,
BLK ZN
SENSOR, IR MOTION
SCREW, 4-40 X 0.38”, PNHD,
PHIL
SCREW, 6-19 X 1-2”, PNHD, PHIL
SCREW, SLFTP, 8-16 X .3125”,
PLASTITE
HOUSING, E-STOP
BUTTON, STOP, MOLDED
SWITCH, BUTTON, STOP
SCREW, 4 X 3/8”, SLFTP, PNHD,
PHIL, ZN, PLASTITE
LABEL, WARNING, CONSOLE
MEMBRANE,AV KEYPAD
PCA,PEM JACK BOARD
BRACKET,AV,LOWER,750T
WELDMENT,AV,750T
ASSY,HANDSET,TOP W-TABS
PEM MOUNTING NUT
423
434
1
1
PL-21178
AW-20892
435
436
1
1
AW-20841
DE-22190
BOLT,1-4-20X0.75,SCHD BTN,BLK
BOLT LCK,1-4-20X.625
BOLT LCK,1-4-20X1.25,G5
COVER,HANDSET BOTTOM
COVER,HANDSET AV MODULE
PCA, HANDSET, UNIVERSAL
CABLE,CAT5E 24” PATCH,BLUE
POWER CORD, IEC NEMA 5-15,
SHORT FOR A/V
CABLE,LOCKING RF and DC
POWER CABLE,2795MM
MONITOR,13.3”, ATSC, NTSC, PEM
MONITOR,13.3”, DVB-T, SECAM,
PAL, PEM
CONSOLE, TOP, A/V, 751T
CABLE, COMP AV JACK BOARD,
GREEN
CABLE,IPOD
LABEL,NIKE+ IPOD
*Language Key
1-German 2-French 3-Spanish 4-English 6-Japanese 7-Swedish 8-Russian A-Danish
751T Console with
A/V Option
408 ATSC
357
422 DVB-T
350
356
Console with
A/V Option
352
354
358
345
423
346
42
360
347
400
359
355
324
314
326
436
435
316
362
AW-20841 A/V Cable
319
DE-22190 Decal, Nike+ iPod
AW-21489
RJ45 Cable
319
353
404
403
363
AW-20241 Power Cord, Short
319
434
406
AW-20892 CABLE, COMP AV
JACK BOARD,GREEN
AW-21499 A/V Cable
Exploded
Views
Page D-3
Cybex 750T Treadmill Owner’s Manual
ITEM QTY. PART NO.
DESCRIPTION
ITEM QTY. PART NO.
DESCRIPTION
23
39
4
17
EH-10291
HS-11977
122
1
AW-20444
123
1
AW-20446
76
2
EH-20244
124
1
AW-20447
102
1
AX-20235
102
1
AX-20236
102
1
AX-20237
125
126
127
128
130
1
1
1
1
1
CN-20252
DE-20558
EC-18896
EH-12208
FS-20232
111
111
111
1
1
1
KAD-22221
KAD-22431
KAD-22223
131
132
134
2
2
4
HN-11925
HS-10405
HS-15732
112
113
114
115
1
1
1
1
AD-21879
AF-20123
AF-20234
AW-19404
135
136
137
1
1
1
HW-10856
RE-20242
SW-19666
116
1
AW-20289
137
1
SW-19667
117
1
AW-20290
118
1
AW-20291
401
409
418
1
1
1
AF-20137
FS-20300
TR-21881
119
120
1
1
AW-22177
AW-20442
419
1
FS-20233
424
1
HS-11894
121
1
AW-20443
TY WRAP BASE
SCREW SEMS, 8-32 X .38, PNHD
PHIL
CLIP, WIRE RETAINER,
.24-.47”DIA
SUB ASSY, 110 VAC
CONTROLLER
SUB ASSY, 220 VAC
CONTROLLER
SUB ASSY, 230 VAC, 50HZ
CONTROLLER
PCA, CONTROLLER, 115 VAC
PCA, CONTROLLER, 230 VAC
PCA, CONTROLLER, 230 VAC,
50Hz
PCA, HUB BOARD
PLATE, SWITCHES
BRACKET,CONTROLLER, PCB
CABLE, CAT5, RJ45 FLAT PATCH
12”
WIRE, INLET TO SWITCH FILTER
JUMPER
WIRE, SWITCH TO FILTER
JUMPER
WIRE, INLET TO GROUND
JUMPER, GREEN
CABLE, MOTOR CONTROLLER
WIRE, FILTER TO OUTLET
JUMPER, BLACK
WIRE, FILTER TO OUTLET
JUMPER, WHITE
NS
1
KMR-20818
WIRE, OUTLET, GROUND JUMPER,
GREEN
WIRE, INLET TO SWITCH JUMPER,
BLACK
WIRE, INLET TO SWITCH JUMPER,
WHITE
PLUG, NEMA 5-15R
LABEL, HUB BOARD
FILTER, 16A
INLET, IEC, 320 16-20 AMP
BRACKET, POWER CORD
RETAINER
KEPS, 10-32, HEX, STL, ZN
SCREW, 4-40 X .25”,PNHD PHIL
SCREW, SEMS, 8-32 UNC X .62”,
PNHD, PHIL
WASHER, LOCK, EXTERNAL, NO. 10
RESISTOR, TM5, DYNAMIC BRAKE
SWITCH, CIRCUIT BREAKER, 15
AMP, 240 VAC
SWITCH, CIRCUIT BREAKER, 20
AMP, 240 VAC
BRACKET, A/V POWER SUPPLY
STRAP, A/V POWER SUPPLY
POWER SUPPLY,12V FAN LOCKING
DC
BRACKET, FAN POWER SUPPLY
RETAINER
SCREW SEMS, 6/32 X .25”, PNHD
PHIL
KIT,FAN REPLACEMENT,PCB
MOTOR CONTROLLER
751T Controller Assembly
111
102
INCLINE
COMM.
DB
INPUT
OUTPUT
39
134
23
137
SW-19667
(20AMP 240 VAC)
39
39
126
127
SW-19666
(15AMP 240 VAC)
39
1
39
2
116
113
136
12" REF
11.25" REF
115
112
AW-20289
SWITCH TO FILTER JUMPER - BLACK
AW-19404
CAT5 RJ45 CABLE
39
118
117
76
L
GND
114
N
128
N
L
135
AW-20291
INLET TO GRND JUMPER - GREEN/ YELLOW
AW-20290
SWITCH TO FILTER JUMPER - WHITE
CHASSIS GND
GND
15.0" REF
11.25" REF
131
76
WHITE
119
BLACK
120
3
125
132
2
NON AV OPTION
1
GREEN OR GREEN/YELLOW
AV OPTION
39
130
6.75" REF
AW-20442
FILTER TO OUTLET JUMPER - BLACK
AW-22177
MOTOR CONTROLLER CABLE
418
401
122
121
6.75" REF
424
AW-20443
FILTER TO OUTLET JUMPER - WHITE
419
11.25" REF
AW-20444
OUTLET GROUND JUMPER - GRN/YEL
39
123
124
409
7.5" REF
7.5" REF
Exploded
Views
Page D-4
AW-21882
Cable, Adapter, Locking DC 2.1MM
AW-20446
INLET TO SWITCH JUMPER - BLACK
AW-20447
INLET TO SWITCH JUMPER - WHITE
Cybex 750T Treadmill Owner’s Manual
ITEM QTY. PART NO.
DESCRIPTION
ITEM QTY. PART NO.
DESCRIPTION
8
9
10
15
16
17
18
19
20
26
1
1
1
1
1
2
2
2
1
4
AX-20383
AX-20452
AX-20453
DE-14486
DE-18413
DE-19360
DE-20392
DE-20393
DE-20427
FS-16511
66
1
PL-20266
67
1
PL-20269
68
1
PL-20270
69
70
74
2
2
2
HS-41107
HW-00165
EH-20254
28
37
38
40
42
1
2
4
12
9
FS-20109
HN-20693
HS-00700
HS-12295
HS-15706
75
77
81
82
83
89
1
1
1
1
1
2
HX-20248
DE-19198
AF-20842
HS-11976
HX-20843
HS-22137
43
8
HS-16509
90
2
PL-22129
45
4
HS-16939
91
92
5
1
EH-00986
DE-22327
51
54
12
14
HW-00180
HW-18123
92
1
DE-22328
59
62
63
64
65
2
1
1
1
1
HX-19102
PL-20262
PL-20263
PL-20264
PL-20265
ASSY, MOTOR COVER
ASSY, END CAP, LEFT
ASSY, END CAP, RIGHT
DECAL SERIAL NUMBER
DECAL, ETL AND CSA
DECAL, CYBEX, BLACK
DECAL, 750T, BLACK
DECAL, 750T, SILVER
DECAL, DISCONNECT POWER
PLATE, REAR RUBBER FOOT
MOUNT
SHIELD, SPLASH
NUT, TEE, 5/16 - 18, 1-2” BARREL
SCREW, 8-32 X 0.50”, PNHD PHIL
BOLT, 1/4 - 20 X 1.75”, HXHD, G5
SCREW, 8-16 X .50”, PNHD, STL,
BLK ZN
SCREW SLFTP, 10 X .5”, PNHD,
PLT, TYP
SCREW SEMS, 10-32 X .75,
PNHD, BLK
WASHER, SPLIT LOCK 1/4”, SST
WASHER, .344 ID X .75 OD X
.125”
FOOT, RUBBER, REAR
COVER, LEFT SIDE FRONT
COVER, RIGHT SIDE FRONT
COVER, FRONT
COVER, REAR, FRAME OUTER,
LEFT
200
203
204
205
1
1
1
2
AF-19890
AX-20331
AX-20332
DE-20305
COVER, REAR, FRAME INNER,
LEFT
COVER, REAR, FRAME OUTER,
RIGHT
COVER, REAR, FRAME INNER,
RIGHT
BOLT, 5/16 - 18 X 1.5”, BTHD, SST
WASHER, SPLIT LOCK 5/16”
CLIP,WIRE RETAINER,.24-.47”,
DIA,.105THK
GROMMET,RUBBER,1.12”DIA
DECAL,CYBEX
BRACKET, MOTOR COVER
SCREW, SEMS, 10-32 X .38”
BUMPER, MOTOR COVER
BOLT, 1/4-14 x 1.25”,HXHD
WSHR,TYP
BRACKET,POWER CORD
STORAGE,PLASTIC
TY WRAP 9”
LABEL,BLACK,INTELLIGENT
SUSPENSION 3
LABEL,SILVER,INTELLIGENT
SUSPENSION 3
WELDMENT, FRAME
ASSY, TOP PLATFORM, LEFT
ASSY, TOP PLATFORM, RIGHT
DECAL, SAFETY WALK
69
70
751T Frame
77
8
45
20
83 81
82 75
28
38
70
38
62
69
45
54
37
64
63
38
45
91
40
51
90
54
54
205
204
200
92
40
51
37
17
89
10
74
54
18 BLACK
19 SILVER
203
205
15
17
16
59
26
43
9
59
26
43
42
42
67
66
65
68
Exploded
Views
Page D-5
Cybex 750T Treadmill Owner’s Manual
ITEM QTY. PART NO.
DESCRIPTION
2
7
24
29
2
1
2
1
AF-20052
AX-20094
FM-20096
FT-16825
30
1
FT-16826
32
33
34
35
46
47
57
58
84
85
2
2
4
2
1
1
4
7
1
1
HB-20097
HB-20098
HN-11136
HN-17935
HS-17936
HS-17937
HW-53017
HX-13771
HN-60064
HS-60022
86
87
1
2
CW-22240
HX-22247
101
1
MR-22239
103
1
MR-19992
103
1
MR-19993
BRACKET, MOTOR,MOUNTING
ASSY, ELEVATION
PIN, ELEVATION PIVOT
SLEEVE, ELEVATION
MOUNTING, TOP
SLEEVE, ELEVATION
MOUNTING, BOTTOM
BEARING, FLANGE, BRONZE
BEARING, THRUST, BRONZE
KEPS 5/16” HEX STL ZINC
NUT LOCK, 3/8 - 24
BOLT, 3/8 - 24 X 2.0”, HXHD CAP
BOLT, 3/8 - 24 X 2.75”, HXHD CAP
WASHER FLAT, 5/16”, SS
RING, RETAINING, 5/8” 0.579 ID
NUT, JAM, 3/8 - 16”, BLACK ZN
BOLT, 3/8 X 2.25”, HXHD, CAP,
BLK
WHEEL,80MM DIA X 32MM W
BUSHING,SPANNER,.500 OD X
1.5”L
ASSY, MOTOR, TREADMILL, AC
DRIVE
MOTOR, ELEVATION, 115 VAC,
60 HZ
MOTOR, ELEVATION, 230 VAC,
50-60 HZ
751T Drive Motor
101
2
57
34
751T Elevation Motor
86
85
87
30
84
24
47
35
58
35
7
29
Exploded
Views
Page D-6
46
103
33
32
Cybex 750T Treadmill Owner’s Manual
ITEM QTY. PART NO.
44
8
201
202
300
1
1
1
500
2
501
502
504
2
4
2
DESCRIPTION
HS-16929
BOLT WHIZ LOCK, 3/8 - 16 X
.625”, HXHD
AF-19921
WELDMENT, UPRIGHT, LEFT
AF-19922
WELDMENT, UPRIGHT, RIGHT
AC-21401-X* ASSY, CONSOLE, 751T, AMBER
LED
HS-41050
BOLT, 5/16-18 x 2.25”, HXHD, G5,
ZN
HW-00189
WASHER, FLAT, 5/16”
HN-42063
NUT, 5/16-18, FLANGED, SS BO
HS-20361
SCREW, SLFTP, 8-16 X 2.5”,
PLASTITE
*Language Key
1-German
2-French
3-Spanish
4-English
6-Japanese
7-Swedish
8-Russian
A-Danish
751T Upright Assembly
300
502
504
502
501
500
202
201
44
44
Exploded
Views
Page D-7
Cybex 750T Treadmill Owner’s Manual
This page intentionally left blank
Exploded
Views
Page D-8
KAD-22221
KAD-22431
KAD-22223
AX-21798-X
KAX-22895-X
SCHEMATIC 751T
Cybex 750T Treadmill Owner’s Manual
Schematic Page E-1
KAD-22221
KAD-22431
KAD-22223
AX-21798-X
KAX-22895-X
SCHEMATIC 751T
With A/V Option
Schematic Page E-2
Cybex 750T Treadmill Owner’s Manual